/*
* linux/arch/arm/mach-sa1100/pleb.c
*/
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/tty.h>
#include <linux/ioport.h>
#include <linux/platform_device.h>
#include <linux/irq.h>
#include <linux/mtd/partitions.h>
#include <asm/hardware.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <asm/mach/serial_sa1100.h>
#include <asm/arch/irqs.h>
#include "generic.h"
/*
* Ethernet IRQ mappings
*/
#define PLEB_ETH0_P (0x20000300) /* Ethernet 0 in PCMCIA0 IO */
#define PLEB_ETH0_V (0xf6000300)
#define GPIO_ETH0_IRQ GPIO_GPIO(21)
#define GPIO_ETH0_EN GPIO_GPIO(26)
#define IRQ_GPIO_ETH0_IRQ IRQ_GPIO21
static struct resource smc91x_resources[] = {
[0] = {
.start = PLEB_ETH0_P,
.end = PLEB_ETH0_P | 0x03ffffff,
.flags = IORESOURCE_MEM,
},
#if 0 /* Autoprobe instead, to get rising/falling edge characteristic right */
[1] = {
.start = IRQ_GPIO_ETH0_IRQ,
.end = IRQ_GPIO_ETH0_IRQ,
.flags = IORESOURCE_IRQ,
},
#endif
};
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
static struct platform_device *devices[] __initdata = {
&smc91x_device,
};
/*
* Pleb's memory map
* has flash memory (typically 4 or 8 meg) selected by
* the two SA1100 lowest chip select outputs.
*/
static struct resource pleb_flash_resources[] = {
[0] = {
.start = SA1100_CS0_PHYS,
.end = SA1100_CS0_PHYS + SZ_8M - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = SA1100_CS1_PHYS,
.end = SA1100_CS1_PHYS + SZ_8M - 1,
.flags = IORESOURCE_MEM,
}
};
static struct mtd_partition pleb_partitions[] = {
{
.name = "blob",
.offset = 0,
.size = 0x00020000,
}, {
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = 0x000e0000,
}, {
.name = "rootfs",
.offset = MTDPART_OFS_APPEND,
.size = 0x00300000,
}
};
static struct flash_platform_data pleb_flash_data = {
.map_name = "cfi_probe",
.parts = pleb_partitions,
.nr_parts = ARRAY_SIZE(pleb_partitions),
};
static void __init pleb_init(void)
{
sa11x0_set_flash_data(&pleb_flash_data, pleb_flash_resources,
ARRAY_SIZE(pleb_flash_resources));
platform_add_devices(devices, ARRAY_SIZE(devices));
}
static void __init pleb_map_io(void)
{
sa1100_map_io();
sa1100_register_uart(0, 3);
sa1100_register_uart(1, 1);
GAFR |= (GPIO_UART_TXD | GPIO_UART_RXD);
GPDR |= GPIO_UART_TXD;
GPDR &= ~GPIO_UART_RXD;
PPAR |= PPAR_UPR;
/*
* Fix expansion memory timing for network card
*/
MECR = ((2<<10) | (2<<5) | (2<<0));
/*
* Enable the SMC ethernet controller
*/
GPDR |= GPIO_ETH0_EN; /* set to output */
GPCR = GPIO_ETH0_EN; /* clear MCLK (enable smc) */
GPDR &= ~GPIO_ETH0_IRQ;
set_irq_type(GPIO_ETH0_IRQ, IRQ_TYPE_EDGE_FALLING);
}
MACHINE_START(PLEB, "PLEB")
.phys_io = 0x80000000,
.io_pg_offst = ((0xf8000000) >> 18) & 0xfffc,
.map_io = pleb_map_io,
.init_irq = sa1100_init_irq,
.timer = &sa1100_timer,
.init_machine = pleb_init,
MACHINE_END
