/*
* linux/arch/arm/mach-pxa/littleton.c
*
* Support for the Marvell Littleton Development Platform.
*
* Author: Jason Chagas (largely modified code)
* Created: Nov 20, 2006
* Copyright: (C) Copyright 2006 Marvell International Ltd.
*
* 2007-11-22 modified to align with latest kernel
* eric miao <eric.miao@marvell.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* publishhed by the Free Software Foundation.
*/
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
#include <asm/types.h>
#include <asm/setup.h>
#include <asm/memory.h>
#include <asm/mach-types.h>
#include <asm/hardware.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/arch/pxa-regs.h>
#include <asm/arch/mfp-pxa300.h>
#include <asm/arch/gpio.h>
#include <asm/arch/pxafb.h>
#include <asm/arch/ssp.h>
#include <asm/arch/littleton.h>
#include "generic.h"
#define ARRAY_AND_SIZE(x) (x), ARRAY_SIZE(x)
/* Littleton MFP configurations */
static mfp_cfg_t littleton_mfp_cfg[] __initdata = {
/* LCD */
GPIO54_LCD_LDD_0,
GPIO55_LCD_LDD_1,
GPIO56_LCD_LDD_2,
GPIO57_LCD_LDD_3,
GPIO58_LCD_LDD_4,
GPIO59_LCD_LDD_5,
GPIO60_LCD_LDD_6,
GPIO61_LCD_LDD_7,
GPIO62_LCD_LDD_8,
GPIO63_LCD_LDD_9,
GPIO64_LCD_LDD_10,
GPIO65_LCD_LDD_11,
GPIO66_LCD_LDD_12,
GPIO67_LCD_LDD_13,
GPIO68_LCD_LDD_14,
GPIO69_LCD_LDD_15,
GPIO70_LCD_LDD_16,
GPIO71_LCD_LDD_17,
GPIO72_LCD_FCLK,
GPIO73_LCD_LCLK,
GPIO74_LCD_PCLK,
GPIO75_LCD_BIAS,
/* SSP2 */
GPIO25_SSP2_SCLK,
GPIO17_SSP2_FRM,
GPIO27_SSP2_TXD,
/* Debug Ethernet */
GPIO90_GPIO,
};
static struct resource smc91x_resources[] = {
[0] = {
.start = (LITTLETON_ETH_PHYS + 0x300),
.end = (LITTLETON_ETH_PHYS + 0xfffff),
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_GPIO(mfp_to_gpio(MFP_PIN_GPIO90)),
.end = IRQ_GPIO(mfp_to_gpio(MFP_PIN_GPIO90)),
.flags = IORESOURCE_IRQ | IRQF_TRIGGER_FALLING,
}
};
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
#if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULES)
/* use bit 30, 31 as the indicator of command parameter number */
#define CMD0(x) ((0x00000000) | ((x) << 9))
#define CMD1(x, x1) ((0x40000000) | ((x) << 9) | 0x100 | (x1))
#define CMD2(x, x1, x2) ((0x80000000) | ((x) << 18) | 0x20000 |\
((x1) << 9) | 0x100 | (x2))
static uint32_t lcd_panel_reset[] = {
CMD0(0x1), /* reset */
CMD0(0x0), /* nop */
CMD0(0x0), /* nop */
CMD0(0x0), /* nop */
};
static uint32_t lcd_panel_on[] = {
CMD0(0x29), /* Display ON */
CMD2(0xB8, 0xFF, 0xF9), /* Output Control */
CMD0(0x11), /* Sleep out */
CMD1(0xB0, 0x16), /* Wake */
};
static uint32_t lcd_panel_off[] = {
CMD0(0x28), /* Display OFF */
CMD2(0xB8, 0x80, 0x02), /* Output Control */
CMD0(0x10), /* Sleep in */
CMD1(0xB0, 0x00), /* Deep stand by in */
};
static uint32_t lcd_vga_pass_through[] = {
CMD1(0xB0, 0x16),
CMD1(0xBC, 0x80),
CMD1(0xE1, 0x00),
CMD1(0x36, 0x50),
CMD1(0x3B, 0x00),
};
static uint32_t lcd_qvga_pass_through[] = {
CMD1(0xB0, 0x16),
CMD1(0xBC, 0x81),
CMD1(0xE1, 0x00),
CMD1(0x36, 0x50),
CMD1(0x3B, 0x22),
};
static uint32_t lcd_vga_transfer[] = {
CMD1(0xcf, 0x02), /* Blanking period control (1) */
CMD2(0xd0, 0x08, 0x04), /* Blanking period control (2) */
CMD1(0xd1, 0x01), /* CKV timing control on/off */
CMD2(0xd2, 0x14, 0x00), /* CKV 1,2 timing control */
CMD2(0xd3, 0x1a, 0x0f), /* OEV timing control */
CMD2(0xd4, 0x1f, 0xaf), /* ASW timing control (1) */
CMD1(0xd5, 0x14), /* ASW timing control (2) */
CMD0(0x21), /* Invert for normally black display */
CMD0(0x29), /* Display on */
};
static uint32_t lcd_qvga_transfer[] = {
CMD1(0xd6, 0x02), /* Blanking period control (1) */
CMD2(0xd7, 0x08, 0x04), /* Blanking period control (2) */
CMD1(0xd8, 0x01), /* CKV timing control on/off */
CMD2(0xd9, 0x00, 0x08), /* CKV 1,2 timing control */
CMD2(0xde, 0x05, 0x0a), /* OEV timing control */
CMD2(0xdf, 0x0a, 0x19), /* ASW timing control (1) */
CMD1(0xe0, 0x0a), /* ASW timing control (2) */
CMD0(0x21), /* Invert for normally black display */
CMD0(0x29), /* Display on */
};
static uint32_t lcd_panel_config[] = {
CMD2(0xb8, 0xff, 0xf9), /* Output control */
CMD0(0x11), /* sleep out */
CMD1(0xba, 0x01), /* Display mode (1) */
CMD1(0xbb, 0x00), /* Display mode (2) */
CMD1(0x3a, 0x60), /* Display mode 18-bit RGB */
CMD1(0xbf, 0x10), /* Drive system change control */
CMD1(0xb1, 0x56), /* Booster operation setup */
CMD1(0xb2, 0x33), /* Booster mode setup */
CMD1(0xb3, 0x11), /* Booster frequency setup */
CMD1(0xb4, 0x02), /* Op amp/system clock */
CMD1(0xb5, 0x35), /* VCS voltage */
CMD1(0xb6, 0x40), /* VCOM voltage */
CMD1(0xb7, 0x03), /* External display signal */
CMD1(0xbd, 0x00), /* ASW slew rate */
CMD1(0xbe, 0x00), /* Dummy data for QuadData operation */
CMD1(0xc0, 0x11), /* Sleep out FR count (A) */
CMD1(0xc1, 0x11), /* Sleep out FR count (B) */
CMD1(0xc2, 0x11), /* Sleep out FR count (C) */
CMD2(0xc3, 0x20, 0x40), /* Sleep out FR count (D) */
CMD2(0xc4, 0x60, 0xc0), /* Sleep out FR count (E) */
CMD2(0xc5, 0x10, 0x20), /* Sleep out FR count (F) */
CMD1(0xc6, 0xc0), /* Sleep out FR count (G) */
CMD2(0xc7, 0x33, 0x43), /* Gamma 1 fine tuning (1) */
CMD1(0xc8, 0x44), /* Gamma 1 fine tuning (2) */
CMD1(0xc9, 0x33), /* Gamma 1 inclination adjustment */
CMD1(0xca, 0x00), /* Gamma 1 blue offset adjustment */
CMD2(0xec, 0x01, 0xf0), /* Horizontal clock cycles */
};
static void ssp_reconfig(struct ssp_dev *dev, int nparam)
{
static int last_nparam = -1;
/* check if it is necessary to re-config SSP */
if (nparam == last_nparam)
return;
ssp_disable(dev);
ssp_config(dev, (nparam == 2) ? 0x0010058a : 0x00100581, 0x18, 0, 0);
last_nparam = nparam;
}
static void ssp_send_cmd(uint32_t *cmd, int num)
{
static int ssp_initialized;
static struct ssp_dev ssp2;
int i;
if (!ssp_initialized) {
ssp_init(&ssp2, 2, SSP_NO_IRQ);
ssp_initialized = 1;
}
clk_enable(ssp2.ssp->clk);
for (i = 0; i < num; i++, cmd++) {
ssp_reconfig(&ssp2, (*cmd >> 30) & 0x3);
ssp_write_word(&ssp2, *cmd & 0x3fffffff);
/* FIXME: ssp_flush() is mandatory here to work */
ssp_flush(&ssp2);
}
clk_disable(ssp2.ssp->clk);
}
static void littleton_lcd_power(int on, struct fb_var_screeninfo *var)
{
if (on) {
ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_on));
ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_reset));
if (var->xres > 240) {
/* VGA */
ssp_send_cmd(ARRAY_AND_SIZE(lcd_vga_pass_through));
ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_config));
ssp_send_cmd(ARRAY_AND_SIZE(lcd_vga_transfer));
} else {
/* QVGA */
ssp_send_cmd(ARRAY_AND_SIZE(lcd_qvga_pass_through));
ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_config));
ssp_send_cmd(ARRAY_AND_SIZE(lcd_qvga_transfer));
}
} else
ssp_send_cmd(ARRAY_AND_SIZE(lcd_panel_off));
}
static struct pxafb_mode_info tpo_tdo24mtea1_modes[] = {
[0] = {
/* VGA */
.pixclock = 38250,
.xres = 480,
.yres = 640,
.bpp = 16,
.hsync_len = 8,
.left_margin = 8,
.right_margin = 24,
.vsync_len = 2,
.upper_margin = 2,
.lower_margin = 4,
.sync = 0,
},
[1] = {
/* QVGA */
.pixclock = 153000,
.xres = 240,
.yres = 320,
.bpp = 16,
.hsync_len = 8,
.left_margin = 8,
.right_margin = 88,
.vsync_len = 2,
.upper_margin = 2,
.lower_margin = 2,
.sync = 0,
},
};
static struct pxafb_mach_info littleton_lcd_info = {
.modes = tpo_tdo24mtea1_modes,
.num_modes = 2,
.lccr0 = LCCR0_Act,
.lccr3 = LCCR3_HSP | LCCR3_VSP,
.pxafb_lcd_power = littleton_lcd_power,
};
static void littleton_init_lcd(void)
{
set_pxa_fb_info(&littleton_lcd_info);
}
#else
static inline void littleton_init_lcd(void) {};
#endif /* CONFIG_FB_PXA || CONFIG_FB_PXA_MODULES */
static void __init littleton_init(void)
{
/* initialize MFP configurations */
pxa3xx_mfp_config(ARRAY_AND_SIZE(littleton_mfp_cfg));
/*
* Note: we depend bootloader set the correct
* value to MSC register for SMC91x.
*/
platform_device_register(&smc91x_device);
littleton_init_lcd();
}
MACHINE_START(LITTLETON, "Marvell Form Factor Development Platform (aka Littleton)")
.phys_io = 0x40000000,
.boot_params = 0xa0000100,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
.map_io = pxa_map_io,
.init_irq = pxa3xx_init_irq,
.timer = &pxa_timer,
.init_machine = littleton_init,
MACHINE_END
