/*
* Hardware definitions for the Toshiba eseries PDAs
*
* Copyright (c) 2003 Ian Molton <spyro@f2s.com>
*
* This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/fb.h>
#include <linux/mfd/tc6393xb.h>
#include <video/w100fb.h>
#include <asm/setup.h>
#include <asm/mach/arch.h>
#include <asm/mach-types.h>
#include <mach/pxa25x.h>
#include <mach/eseries-gpio.h>
#include <mach/udc.h>
#include <mach/irqs.h>
#include <mach/audio.h>
#include "generic.h"
#include "eseries.h"
#include "clock.h"
/* ------------------------ e800 LCD definitions ------------------------- */
static unsigned long e800_pin_config[] __initdata = {
/* AC97 */
GPIO28_AC97_BITCLK,
GPIO29_AC97_SDATA_IN_0,
GPIO30_AC97_SDATA_OUT,
GPIO31_AC97_SYNC,
};
static struct w100_gen_regs e800_lcd_regs = {
.lcd_format = 0x00008003,
.lcdd_cntl1 = 0x02a00000,
.lcdd_cntl2 = 0x0003ffff,
.genlcd_cntl1 = 0x000ff2a3,
.genlcd_cntl2 = 0x000002a3,
.genlcd_cntl3 = 0x000102aa,
};
static struct w100_mode e800_lcd_mode[2] = {
[0] = {
.xres = 480,
.yres = 640,
.left_margin = 52,
.right_margin = 148,
.upper_margin = 2,
.lower_margin = 6,
.crtc_ss = 0x80350034,
.crtc_ls = 0x802b0026,
.crtc_gs = 0x80160016,
.crtc_vpos_gs = 0x00020003,
.crtc_rev = 0x0040001d,
.crtc_dclk = 0xe0000000,
.crtc_gclk = 0x82a50049,
.crtc_goe = 0x80ee001c,
.crtc_ps1_active = 0x00000000,
.pll_freq = 128,
.pixclk_divider = 4,
.pixclk_divider_rotated = 6,
.pixclk_src = CLK_SRC_PLL,
.sysclk_divider = 0,
.sysclk_src = CLK_SRC_PLL,
},
[1] = {
.xres = 240,
.yres = 320,
.left_margin = 15,
.right_margin = 88,
.upper_margin = 0,
.lower_margin = 7,
.crtc_ss = 0xd010000f,
.crtc_ls = 0x80070003,
.crtc_gs = 0x80000000,
.crtc_vpos_gs = 0x01460147,
.crtc_rev = 0x00400003,
.crtc_dclk = 0xa1700030,
.crtc_gclk = 0x814b0008,
.crtc_goe = 0x80cc0015,
.crtc_ps1_active = 0x00000000,
.pll_freq = 100,
.pixclk_divider = 6, /* Wince uses 14 which gives a */
.pixclk_divider_rotated = 6, /* 7MHz Pclk. We use a 14MHz one */
.pixclk_src = CLK_SRC_PLL,
.sysclk_divider = 0,
.sysclk_src = CLK_SRC_PLL,
}
};
static struct w100_gpio_regs e800_w100_gpio_info = {
.init_data1 = 0xc13fc019,
.gpio_dir1 = 0x3e40df7f,
.gpio_oe1 = 0x003c3000,
.init_data2 = 0x00000000,
.gpio_dir2 = 0x00000000,
.gpio_oe2 = 0x00000000,
};
static struct w100_mem_info e800_w100_mem_info = {
.ext_cntl = 0x09640011,
.sdram_mode_reg = 0x00600021,
.ext_timing_cntl = 0x10001545,
.io_cntl = 0x7ddd7333,
.size = 0x1fffff,
};
static void e800_tg_change(struct w100fb_par *par)
{
unsigned long tmp;
tmp = w100fb_gpio_read(W100_GPIO_PORT_A);
if (par->mode->xres == 480)
tmp |= 0x100;
else
tmp &= ~0x100;
w100fb_gpio_write(W100_GPIO_PORT_A, tmp);
}
static struct w100_tg_info e800_tg_info = {
.change = e800_tg_change,
};
static struct w100fb_mach_info e800_fb_info = {
.modelist = e800_lcd_mode,
.num_modes = 2,
.regs = &e800_lcd_regs,
.gpio = &e800_w100_gpio_info,
.mem = &e800_w100_mem_info,
.tg = &e800_tg_info,
.xtal_freq = 16000000,
};
static struct resource e800_fb_resources[] = {
[0] = {
.start = 0x0c000000,
.end = 0x0cffffff,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device e800_fb_device = {
.name = "w100fb",
.id = -1,
.dev = {
.platform_data = &e800_fb_info,
},
.num_resources = ARRAY_SIZE(e800_fb_resources),
.resource = e800_fb_resources,
};
/* --------------------------- UDC definitions --------------------------- */
static struct pxa2xx_udc_mach_info e800_udc_mach_info = {
.gpio_vbus = GPIO_E800_USB_DISC,
.gpio_pullup = GPIO_E800_USB_PULLUP,
.gpio_pullup_inverted = 1
};
/* ----------------- e800 tc6393xb parameters ------------------ */
static struct tc6393xb_platform_data e800_tc6393xb_info = {
.irq_base = IRQ_BOARD_START,
.scr_pll2cr = 0x0cc1,
.scr_gper = 0,
.gpio_base = -1,
.suspend = &eseries_tmio_suspend,
.resume = &eseries_tmio_resume,
.enable = &eseries_tmio_enable,
.disable = &eseries_tmio_disable,
};
static struct platform_device e800_tc6393xb_device = {
.name = "tc6393xb",
.id = -1,
.dev = {
.platform_data = &e800_tc6393xb_info,
},
.num_resources = 2,
.resource = eseries_tmio_resources,
};
/* ----------------------------------------------------------------------- */
static struct platform_device *devices[] __initdata = {
&e800_fb_device,
&e800_tc6393xb_device,
};
static void __init e800_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(e800_pin_config));
pxa_set_ffuart_info(NULL);
pxa_set_btuart_info(NULL);
pxa_set_stuart_info(NULL);
clk_add_alias("CLK_CK3P6MI", e800_tc6393xb_device.name,
"GPIO11_CLK", NULL),
eseries_get_tmio_gpios();
platform_add_devices(devices, ARRAY_SIZE(devices));
pxa_set_udc_info(&e800_udc_mach_info);
pxa_set_ac97_info(NULL);
}
MACHINE_START(E800, "Toshiba e800")
/* Maintainer: Ian Molton (spyro@f2s.com) */
.phys_io = 0x40000000,
.io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
.boot_params = 0xa0000100,
.map_io = pxa_map_io,
.init_irq = pxa25x_init_irq,
.fixup = eseries_fixup,
.init_machine = e800_init,
.timer = &pxa_timer,
MACHINE_END
