/*
* arch/arm/mach-orion5x/kurobox_pro-setup.c
*
* Maintainer: Ronen Shitrit <rshitrit@marvell.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/pci.h>
#include <linux/irq.h>
#include <linux/delay.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/nand.h>
#include <linux/mv643xx_eth.h>
#include <linux/i2c.h>
#include <linux/serial_reg.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
#include <asm/gpio.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
#include <plat/orion_nand.h>
#include "common.h"
#include "mpp.h"
/*****************************************************************************
* KUROBOX-PRO Info
****************************************************************************/
/*
* 256K NOR flash Device bus boot chip select
*/
#define KUROBOX_PRO_NOR_BOOT_BASE 0xf4000000
#define KUROBOX_PRO_NOR_BOOT_SIZE SZ_256K
/*
* 256M NAND flash on Device bus chip select 1
*/
#define KUROBOX_PRO_NAND_BASE 0xfc000000
#define KUROBOX_PRO_NAND_SIZE SZ_2M
/*****************************************************************************
* 256MB NAND Flash on Device bus CS0
****************************************************************************/
static struct mtd_partition kurobox_pro_nand_parts[] = {
{
.name = "uImage",
.offset = 0,
.size = SZ_4M,
}, {
.name = "rootfs",
.offset = SZ_4M,
.size = SZ_64M,
}, {
.name = "extra",
.offset = SZ_4M + SZ_64M,
.size = SZ_256M - (SZ_4M + SZ_64M),
},
};
static struct resource kurobox_pro_nand_resource = {
.flags = IORESOURCE_MEM,
.start = KUROBOX_PRO_NAND_BASE,
.end = KUROBOX_PRO_NAND_BASE + KUROBOX_PRO_NAND_SIZE - 1,
};
static struct orion_nand_data kurobox_pro_nand_data = {
.parts = kurobox_pro_nand_parts,
.nr_parts = ARRAY_SIZE(kurobox_pro_nand_parts),
.cle = 0,
.ale = 1,
.width = 8,
};
static struct platform_device kurobox_pro_nand_flash = {
.name = "orion_nand",
.id = -1,
.dev = {
.platform_data = &kurobox_pro_nand_data,
},
.resource = &kurobox_pro_nand_resource,
.num_resources = 1,
};
/*****************************************************************************
* 256KB NOR Flash on BOOT Device
****************************************************************************/
static struct physmap_flash_data kurobox_pro_nor_flash_data = {
.width = 1,
};
static struct resource kurobox_pro_nor_flash_resource = {
.flags = IORESOURCE_MEM,
.start = KUROBOX_PRO_NOR_BOOT_BASE,
.end = KUROBOX_PRO_NOR_BOOT_BASE + KUROBOX_PRO_NOR_BOOT_SIZE - 1,
};
static struct platform_device kurobox_pro_nor_flash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &kurobox_pro_nor_flash_data,
},
.num_resources = 1,
.resource = &kurobox_pro_nor_flash_resource,
};
/*****************************************************************************
* PCI
****************************************************************************/
static int __init kurobox_pro_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
{
int irq;
/*
* Check for devices with hard-wired IRQs.
*/
irq = orion5x_pci_map_irq(dev, slot, pin);
if (irq != -1)
return irq;
/*
* PCI isn't used on the Kuro
*/
return -1;
}
static struct hw_pci kurobox_pro_pci __initdata = {
.nr_controllers = 2,
.swizzle = pci_std_swizzle,
.setup = orion5x_pci_sys_setup,
.scan = orion5x_pci_sys_scan_bus,
.map_irq = kurobox_pro_pci_map_irq,
};
static int __init kurobox_pro_pci_init(void)
{
if (machine_is_kurobox_pro()) {
orion5x_pci_disable();
pci_common_init(&kurobox_pro_pci);
}
return 0;
}
subsys_initcall(kurobox_pro_pci_init);
/*****************************************************************************
* Ethernet
****************************************************************************/
static struct mv643xx_eth_platform_data kurobox_pro_eth_data = {
.phy_addr = 8,
};
/*****************************************************************************
* RTC 5C372a on I2C bus
****************************************************************************/
static struct i2c_board_info __initdata kurobox_pro_i2c_rtc = {
I2C_BOARD_INFO("rs5c372a", 0x32),
};
/*****************************************************************************
* SATA
****************************************************************************/
static struct mv_sata_platform_data kurobox_pro_sata_data = {
.n_ports = 2,
};
/*****************************************************************************
* Kurobox Pro specific power off method via UART1-attached microcontroller
****************************************************************************/
#define UART1_REG(x) (UART1_VIRT_BASE + ((UART_##x) << 2))
static int kurobox_pro_miconread(unsigned char *buf, int count)
{
int i;
int timeout;
for (i = 0; i < count; i++) {
timeout = 10;
while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) {
if (--timeout == 0)
break;
udelay(1000);
}
if (timeout == 0)
break;
buf[i] = readl(UART1_REG(RX));
}
/* return read bytes */
return i;
}
static int kurobox_pro_miconwrite(const unsigned char *buf, int count)
{
int i = 0;
while (count--) {
while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE))
barrier();
writel(buf[i++], UART1_REG(TX));
}
return 0;
}
static int kurobox_pro_miconsend(const unsigned char *data, int count)
{
int i;
unsigned char checksum = 0;
unsigned char recv_buf[40];
unsigned char send_buf[40];
unsigned char correct_ack[3];
int retry = 2;
/* Generate checksum */
for (i = 0; i < count; i++)
checksum -= data[i];
do {
/* Send data */
kurobox_pro_miconwrite(data, count);
/* send checksum */
kurobox_pro_miconwrite(&checksum, 1);
if (kurobox_pro_miconread(recv_buf, sizeof(recv_buf)) <= 3) {
printk(KERN_ERR ">%s: receive failed.\n", __func__);
/* send preamble to clear the receive buffer */
memset(&send_buf, 0xff, sizeof(send_buf));
kurobox_pro_miconwrite(send_buf, sizeof(send_buf));
/* make dummy reads */
mdelay(100);
kurobox_pro_miconread(recv_buf, sizeof(recv_buf));
} else {
/* Generate expected ack */
correct_ack[0] = 0x01;
correct_ack[1] = data[1];
correct_ack[2] = 0x00;
/* checksum Check */
if ((recv_buf[0] + recv_buf[1] + recv_buf[2] +
recv_buf[3]) & 0xFF) {
printk(KERN_ERR ">%s: Checksum Error : "
"Received data[%02x, %02x, %02x, %02x]"
"\n", __func__, recv_buf[0],
recv_buf[1], recv_buf[2], recv_buf[3]);
} else {
/* Check Received Data */
if (correct_ack[0] == recv_buf[0] &&
correct_ack[1] == recv_buf[1] &&
correct_ack[2] == recv_buf[2]) {
/* Interval for next command */
mdelay(10);
/* Receive ACK */
return 0;
}
}
/* Received NAK or illegal Data */
printk(KERN_ERR ">%s: Error : NAK or Illegal Data "
"Received\n", __func__);
}
} while (retry--);
/* Interval for next command */
mdelay(10);
return -1;
}
static void kurobox_pro_power_off(void)
{
const unsigned char watchdogkill[] = {0x01, 0x35, 0x00};
const unsigned char shutdownwait[] = {0x00, 0x0c};
const unsigned char poweroff[] = {0x00, 0x06};
/* 38400 baud divisor */
const unsigned divisor = ((ORION5X_TCLK + (8 * 38400)) / (16 * 38400));
pr_info("%s: triggering power-off...\n", __func__);
/* hijack uart1 and reset into sane state (38400,8n1,even parity) */
writel(0x83, UART1_REG(LCR));
writel(divisor & 0xff, UART1_REG(DLL));
writel((divisor >> 8) & 0xff, UART1_REG(DLM));
writel(0x1b, UART1_REG(LCR));
writel(0x00, UART1_REG(IER));
writel(0x07, UART1_REG(FCR));
writel(0x00, UART1_REG(MCR));
/* Send the commands to shutdown the Kurobox Pro */
kurobox_pro_miconsend(watchdogkill, sizeof(watchdogkill)) ;
kurobox_pro_miconsend(shutdownwait, sizeof(shutdownwait)) ;
kurobox_pro_miconsend(poweroff, sizeof(poweroff));
}
/*****************************************************************************
* General Setup
****************************************************************************/
static struct orion5x_mpp_mode kurobox_pro_mpp_modes[] __initdata = {
{ 0, MPP_UNUSED },
{ 1, MPP_UNUSED },
{ 2, MPP_GPIO }, /* GPIO Micon */
{ 3, MPP_GPIO }, /* GPIO Rtc */
{ 4, MPP_UNUSED },
{ 5, MPP_UNUSED },
{ 6, MPP_NAND }, /* NAND Flash REn */
{ 7, MPP_NAND }, /* NAND Flash WEn */
{ 8, MPP_UNUSED },
{ 9, MPP_UNUSED },
{ 10, MPP_UNUSED },
{ 11, MPP_UNUSED },
{ 12, MPP_SATA_LED }, /* SATA 0 presence */
{ 13, MPP_SATA_LED }, /* SATA 1 presence */
{ 14, MPP_SATA_LED }, /* SATA 0 active */
{ 15, MPP_SATA_LED }, /* SATA 1 active */
{ 16, MPP_UART }, /* UART1 RXD */
{ 17, MPP_UART }, /* UART1 TXD */
{ 18, MPP_UART }, /* UART1 CTSn */
{ 19, MPP_UART }, /* UART1 RTSn */
{ -1 },
};
static void __init kurobox_pro_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(kurobox_pro_mpp_modes);
/*
* Configure peripherals.
*/
orion5x_ehci0_init();
orion5x_ehci1_init();
orion5x_eth_init(&kurobox_pro_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&kurobox_pro_sata_data);
orion5x_uart0_init();
orion5x_uart1_init();
orion5x_xor_init();
orion5x_setup_dev_boot_win(KUROBOX_PRO_NOR_BOOT_BASE,
KUROBOX_PRO_NOR_BOOT_SIZE);
platform_device_register(&kurobox_pro_nor_flash);
if (machine_is_kurobox_pro()) {
orion5x_setup_dev0_win(KUROBOX_PRO_NAND_BASE,
KUROBOX_PRO_NAND_SIZE);
platform_device_register(&kurobox_pro_nand_flash);
}
i2c_register_board_info(0, &kurobox_pro_i2c_rtc, 1);
/* register Kurobox Pro specific power-off method */
pm_power_off = kurobox_pro_power_off;
}
#ifdef CONFIG_MACH_KUROBOX_PRO
MACHINE_START(KUROBOX_PRO, "Buffalo/Revogear Kurobox Pro")
/* Maintainer: Ronen Shitrit <rshitrit@marvell.com> */
.phys_io = ORION5X_REGS_PHYS_BASE,
.io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
.boot_params = 0x00000100,
.init_machine = kurobox_pro_init,
.map_io = orion5x_map_io,
.init_irq = orion5x_init_irq,
.timer = &orion5x_timer,
.fixup = tag_fixup_mem32,
MACHINE_END
#endif
#ifdef CONFIG_MACH_LINKSTATION_PRO
MACHINE_START(LINKSTATION_PRO, "Buffalo Linkstation Pro/Live")
/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
.phys_io = ORION5X_REGS_PHYS_BASE,
.io_pg_offst = ((ORION5X_REGS_VIRT_BASE) >> 18) & 0xFFFC,
.boot_params = 0x00000100,
.init_machine = kurobox_pro_init,
.map_io = orion5x_map_io,
.init_irq = orion5x_init_irq,
.timer = &orion5x_timer,
.fixup = tag_fixup_mem32,
MACHINE_END
#endif
