/*
* opp2xxx.h - macros for old-style OMAP2xxx "OPP" definitions
*
* Copyright (C) 2005-2009 Texas Instruments, Inc.
* Copyright (C) 2004-2009 Nokia Corporation
*
* Richard Woodruff <r-woodruff2@ti.com>
*
* The OMAP2 processor can be run at several discrete 'PRCM configurations'.
* These configurations are characterized by voltage and speed for clocks.
* The device is only validated for certain combinations. One way to express
* these combinations is via the 'ratio's' which the clocks operate with
* respect to each other. These ratio sets are for a given voltage/DPLL
* setting. All configurations can be described by a DPLL setting and a ratio
* There are 3 ratio sets for the 2430 and X ratio sets for 2420.
*
* 2430 differs from 2420 in that there are no more phase synchronizers used.
* They both have a slightly different clock domain setup. 2420(iva1,dsp) vs
* 2430 (iva2.1, NOdsp, mdm)
*
* XXX Missing voltage data.
*
* THe format described in this file is deprecated. Once a reasonable
* OPP API exists, the data in this file should be converted to use it.
*
* This is technically part of the OMAP2xxx clock code.
*/
#ifndef __ARCH_ARM_MACH_OMAP2_OPP2XXX_H
#define __ARCH_ARM_MACH_OMAP2_OPP2XXX_H
/**
* struct prcm_config - define clock rates on a per-OPP basis (24xx)
*
* Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated.
* xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,CM_CLKSEL_DSP
* CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL CM_CLKSEL2_PLL, CM_CLKSEL_MDM
*
* This is deprecated. As soon as we have a decent OPP API, we should
* move all this stuff to it.
*/
struct prcm_config {
unsigned long xtal_speed; /* crystal rate */
unsigned long dpll_speed; /* dpll: out*xtal*M/(N-1)table_recalc */
unsigned long mpu_speed; /* speed of MPU */
unsigned long cm_clksel_mpu; /* mpu divider */
unsigned long cm_clksel_dsp; /* dsp+iva1 div(2420), iva2.1(2430) */
unsigned long cm_clksel_gfx; /* gfx dividers */
unsigned long cm_clksel1_core; /* major subsystem dividers */
unsigned long cm_clksel1_pll; /* m,n */
unsigned long cm_clksel2_pll; /* dpllx1 or x2 out */
unsigned long cm_clksel_mdm; /* modem dividers 2430 only */
unsigned long base_sdrc_rfr; /* base refresh timing for a set */
unsigned char flags;
};
/* Core fields for cm_clksel, not ratio governed */
#define RX_CLKSEL_DSS1 (0x10 << 8)
#define RX_CLKSEL_DSS2 (0x0 << 13)
#define RX_CLKSEL_SSI (0x5 << 20)
/*-------------------------------------------------------------------------
* Voltage/DPLL ratios
*-------------------------------------------------------------------------*/
/* 2430 Ratio's, 2430-Ratio Config 1 */
#define R1_CLKSEL_L3 (4 << 0)
#define R1_CLKSEL_L4 (2 << 5)
#define R1_CLKSEL_USB (4 << 25)
#define R1_CM_CLKSEL1_CORE_VAL (R1_CLKSEL_USB | RX_CLKSEL_SSI | \
RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \
R1_CLKSEL_L4 | R1_CLKSEL_L3)
#define R1_CLKSEL_MPU (2 << 0)
#define R1_CM_CLKSEL_MPU_VAL R1_CLKSEL_MPU
#define R1_CLKSEL_DSP (2 << 0)
#define R1_CLKSEL_DSP_IF (2 << 5)
#define R1_CM_CLKSEL_DSP_VAL (R1_CLKSEL_DSP | R1_CLKSEL_DSP_IF)
#define R1_CLKSEL_GFX (2 << 0)
#define R1_CM_CLKSEL_GFX_VAL R1_CLKSEL_GFX
#define R1_CLKSEL_MDM (4 << 0)
#define R1_CM_CLKSEL_MDM_VAL R1_CLKSEL_MDM
/* 2430-Ratio Config 2 */
#define R2_CLKSEL_L3 (6 << 0)
#define R2_CLKSEL_L4 (2 << 5)
#define R2_CLKSEL_USB (2 << 25)
#define R2_CM_CLKSEL1_CORE_VAL (R2_CLKSEL_USB | RX_CLKSEL_SSI | \
RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \
R2_CLKSEL_L4 | R2_CLKSEL_L3)
#define R2_CLKSEL_MPU (2 << 0)
#define R2_CM_CLKSEL_MPU_VAL R2_CLKSEL_MPU
#define R2_CLKSEL_DSP (2 << 0)
#define R2_CLKSEL_DSP_IF (3 << 5)
#define R2_CM_CLKSEL_DSP_VAL (R2_CLKSEL_DSP | R2_CLKSEL_DSP_IF)
#define R2_CLKSEL_GFX (2 << 0)
#define R2_CM_CLKSEL_GFX_VAL R2_CLKSEL_GFX
#define R2_CLKSEL_MDM (6 << 0)
#define R2_CM_CLKSEL_MDM_VAL R2_CLKSEL_MDM
/* 2430-Ratio Bootm (BYPASS) */
#define RB_CLKSEL_L3 (1 << 0)
#define RB_CLKSEL_L4 (1 << 5)
#define RB_CLKSEL_USB (1 << 25)
#define RB_CM_CLKSEL1_CORE_VAL (RB_CLKSEL_USB | RX_CLKSEL_SSI | \
RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \
RB_CLKSEL_L4 | RB_CLKSEL_L3)
#define RB_CLKSEL_MPU (1 << 0)
#define RB_CM_CLKSEL_MPU_VAL RB_CLKSEL_MPU
#define RB_CLKSEL_DSP (1 << 0)
#define RB_CLKSEL_DSP_IF (1 << 5)
#define RB_CM_CLKSEL_DSP_VAL (RB_CLKSEL_DSP | RB_CLKSEL_DSP_IF)
#define RB_CLKSEL_GFX (1 << 0)
#define RB_CM_CLKSEL_GFX_VAL RB_CLKSEL_GFX
#define RB_CLKSEL_MDM (1 << 0)
#define RB_CM_CLKSEL_MDM_VAL RB_CLKSEL_MDM
/* 2420 Ratio Equivalents */
#define RXX_CLKSEL_VLYNQ (0x12 << 15)
#define RXX_CLKSEL_SSI (0x8 << 20)
/* 2420-PRCM III 532MHz core */
#define RIII_CLKSEL_L3 (4 << 0) /* 133MHz */
#define RIII_CLKSEL_L4 (2 << 5) /* 66.5MHz */
#define RIII_CLKSEL_USB (4 << 25) /* 33.25MHz */
#define RIII_CM_CLKSEL1_CORE_VAL (RIII_CLKSEL_USB | RXX_CLKSEL_SSI | \
RXX_CLKSEL_VLYNQ | RX_CLKSEL_DSS2 | \
RX_CLKSEL_DSS1 | RIII_CLKSEL_L4 | \
RIII_CLKSEL_L3)
#define RIII_CLKSEL_MPU (2 << 0) /* 266MHz */
#define RIII_CM_CLKSEL_MPU_VAL RIII_CLKSEL_MPU
#define RIII_CLKSEL_DSP (3 << 0) /* c5x - 177.3MHz */
#define RIII_CLKSEL_DSP_IF (2 << 5) /* c5x - 88.67MHz */
#define RIII_SYNC_DSP (1 << 7) /* Enable sync */
#define RIII_CLKSEL_IVA (6 << 8) /* iva1 - 88.67MHz */
#define RIII_SYNC_IVA (1 << 13) /* Enable sync */
#define RIII_CM_CLKSEL_DSP_VAL (RIII_SYNC_IVA | RIII_CLKSEL_IVA | \
RIII_SYNC_DSP | RIII_CLKSEL_DSP_IF | \
RIII_CLKSEL_DSP)
#define RIII_CLKSEL_GFX (2 << 0) /* 66.5MHz */
#define RIII_CM_CLKSEL_GFX_VAL RIII_CLKSEL_GFX
/* 2420-PRCM II 600MHz core */
#define RII_CLKSEL_L3 (6 << 0) /* 100MHz */
#define RII_CLKSEL_L4 (2 << 5) /* 50MHz */
#define RII_CLKSEL_USB (2 << 25) /* 50MHz */
#define RII_CM_CLKSEL1_CORE_VAL (RII_CLKSEL_USB | RXX_CLKSEL_SSI | \
RXX_CLKSEL_VLYNQ | RX_CLKSEL_DSS2 | \
RX_CLKSEL_DSS1 | RII_CLKSEL_L4 | \
RII_CLKSEL_L3)
#define RII_CLKSEL_MPU (2 << 0) /* 300MHz */
#define RII_CM_CLKSEL_MPU_VAL RII_CLKSEL_MPU
#define RII_CLKSEL_DSP (3 << 0) /* c5x - 200MHz */
#define RII_CLKSEL_DSP_IF (2 << 5) /* c5x - 100MHz */
#define RII_SYNC_DSP (0 << 7) /* Bypass sync */
#define RII_CLKSEL_IVA (3 << 8) /* iva1 - 200MHz */
#define RII_SYNC_IVA (0 << 13) /* Bypass sync */
#define RII_CM_CLKSEL_DSP_VAL (RII_SYNC_IVA | RII_CLKSEL_IVA | \
RII_SYNC_DSP | RII_CLKSEL_DSP_IF | \
RII_CLKSEL_DSP)
#define RII_CLKSEL_GFX (2 << 0) /* 50MHz */
#define RII_CM_CLKSEL_GFX_VAL RII_CLKSEL_GFX
/* 2420-PRCM I 660MHz core */
#define RI_CLKSEL_L3 (4 << 0) /* 165MHz */
#define RI_CLKSEL_L4 (2 << 5) /* 82.5MHz */
#define RI_CLKSEL_USB (4 << 25) /* 41.25MHz */
#define RI_CM_CLKSEL1_CORE_VAL (RI_CLKSEL_USB | \
RXX_CLKSEL_SSI | RXX_CLKSEL_VLYNQ | \
RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \
RI_CLKSEL_L4 | RI_CLKSEL_L3)
#define RI_CLKSEL_MPU (2 << 0) /* 330MHz */
#define RI_CM_CLKSEL_MPU_VAL RI_CLKSEL_MPU
#define RI_CLKSEL_DSP (3 << 0) /* c5x - 220MHz */
#define RI_CLKSEL_DSP_IF (2 << 5) /* c5x - 110MHz */
#define RI_SYNC_DSP (1 << 7) /* Activate sync */
#define RI_CLKSEL_IVA (4 << 8) /* iva1 - 165MHz */
#define RI_SYNC_IVA (0 << 13) /* Bypass sync */
#define RI_CM_CLKSEL_DSP_VAL (RI_SYNC_IVA | RI_CLKSEL_IVA | \
RI_SYNC_DSP | RI_CLKSEL_DSP_IF | \
RI_CLKSEL_DSP)
#define RI_CLKSEL_GFX (1 << 0) /* 165MHz */
#define RI_CM_CLKSEL_GFX_VAL RI_CLKSEL_GFX
/* 2420-PRCM VII (boot) */
#define RVII_CLKSEL_L3 (1 << 0)
#define RVII_CLKSEL_L4 (1 << 5)
#define RVII_CLKSEL_DSS1 (1 << 8)
#define RVII_CLKSEL_DSS2 (0 << 13)
#define RVII_CLKSEL_VLYNQ (1 << 15)
#define RVII_CLKSEL_SSI (1 << 20)
#define RVII_CLKSEL_USB (1 << 25)
#define RVII_CM_CLKSEL1_CORE_VAL (RVII_CLKSEL_USB | RVII_CLKSEL_SSI | \
RVII_CLKSEL_VLYNQ | \
RVII_CLKSEL_DSS2 | RVII_CLKSEL_DSS1 | \
RVII_CLKSEL_L4 | RVII_CLKSEL_L3)
#define RVII_CLKSEL_MPU (1 << 0) /* all divide by 1 */
#define RVII_CM_CLKSEL_MPU_VAL RVII_CLKSEL_MPU
#define RVII_CLKSEL_DSP (1 << 0)
#define RVII_CLKSEL_DSP_IF (1 << 5)
#define RVII_SYNC_DSP (0 << 7)
#define RVII_CLKSEL_IVA (1 << 8)
#define RVII_SYNC_IVA (0 << 13)
#define RVII_CM_CLKSEL_DSP_VAL (RVII_SYNC_IVA | RVII_CLKSEL_IVA | \
RVII_SYNC_DSP | RVII_CLKSEL_DSP_IF | \
RVII_CLKSEL_DSP)
#define RVII_CLKSEL_GFX (1 << 0)
#define RVII_CM_CLKSEL_GFX_VAL RVII_CLKSEL_GFX
/*-------------------------------------------------------------------------
* 2430 Target modes: Along with each configuration the CPU has several
* modes which goes along with them. Modes mainly are the addition of
* describe DPLL combinations to go along with a ratio.
*-------------------------------------------------------------------------*/
/* Hardware governed */
#define MX_48M_SRC (0 << 3)
#define MX_54M_SRC (0 << 5)
#define MX_APLLS_CLIKIN_12 (3 << 23)
#define MX_APLLS_CLIKIN_13 (2 << 23)
#define MX_APLLS_CLIKIN_19_2 (0 << 23)
/*
* 2430 - standalone, 2*ref*M/(n+1), M/N is for exactness not relock speed
* #5a (ratio1) baseport-target, target DPLL = 266*2 = 532MHz
*/
#define M5A_DPLL_MULT_12 (133 << 12)
#define M5A_DPLL_DIV_12 (5 << 8)
#define M5A_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
M5A_DPLL_DIV_12 | M5A_DPLL_MULT_12 | \
MX_APLLS_CLIKIN_12)
#define M5A_DPLL_MULT_13 (61 << 12)
#define M5A_DPLL_DIV_13 (2 << 8)
#define M5A_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \
M5A_DPLL_DIV_13 | M5A_DPLL_MULT_13 | \
MX_APLLS_CLIKIN_13)
#define M5A_DPLL_MULT_19 (55 << 12)
#define M5A_DPLL_DIV_19 (3 << 8)
#define M5A_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \
M5A_DPLL_DIV_19 | M5A_DPLL_MULT_19 | \
MX_APLLS_CLIKIN_19_2)
/* #5b (ratio1) target DPLL = 200*2 = 400MHz */
#define M5B_DPLL_MULT_12 (50 << 12)
#define M5B_DPLL_DIV_12 (2 << 8)
#define M5B_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
M5B_DPLL_DIV_12 | M5B_DPLL_MULT_12 | \
MX_APLLS_CLIKIN_12)
#define M5B_DPLL_MULT_13 (200 << 12)
#define M5B_DPLL_DIV_13 (12 << 8)
#define M5B_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \
M5B_DPLL_DIV_13 | M5B_DPLL_MULT_13 | \
MX_APLLS_CLIKIN_13)
#define M5B_DPLL_MULT_19 (125 << 12)
#define M5B_DPLL_DIV_19 (31 << 8)
#define M5B_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \
M5B_DPLL_DIV_19 | M5B_DPLL_MULT_19 | \
MX_APLLS_CLIKIN_19_2)
/*
* #4 (ratio2), DPLL = 399*2 = 798MHz, L3=133MHz
*/
#define M4_DPLL_MULT_12 (133 << 12)
#define M4_DPLL_DIV_12 (3 << 8)
#define M4_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
M4_DPLL_DIV_12 | M4_DPLL_MULT_12 | \
MX_APLLS_CLIKIN_12)
#define M4_DPLL_MULT_13 (399 << 12)
#define M4_DPLL_DIV_13 (12 << 8)
#define M4_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \
M4_DPLL_DIV_13 | M4_DPLL_MULT_13 | \
MX_APLLS_CLIKIN_13)
#define M4_DPLL_MULT_19 (145 << 12)
#define M4_DPLL_DIV_19 (6 << 8)
#define M4_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \
M4_DPLL_DIV_19 | M4_DPLL_MULT_19 | \
MX_APLLS_CLIKIN_19_2)
/*
* #3 (ratio2) baseport-target, target DPLL = 330*2 = 660MHz
*/
#define M3_DPLL_MULT_12 (55 << 12)
#define M3_DPLL_DIV_12 (1 << 8)
#define M3_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
M3_DPLL_DIV_12 | M3_DPLL_MULT_12 | \
MX_APLLS_CLIKIN_12)
#define M3_DPLL_MULT_13 (76 << 12)
#define M3_DPLL_DIV_13 (2 << 8)
#define M3_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \
M3_DPLL_DIV_13 | M3_DPLL_MULT_13 | \
MX_APLLS_CLIKIN_13)
#define M3_DPLL_MULT_19 (17 << 12)
#define M3_DPLL_DIV_19 (0 << 8)
#define M3_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \
M3_DPLL_DIV_19 | M3_DPLL_MULT_19 | \
MX_APLLS_CLIKIN_19_2)
/*
* #2 (ratio1) DPLL = 330*2 = 660MHz, L3=165MHz
*/
#define M2_DPLL_MULT_12 (55 << 12)
#define M2_DPLL_DIV_12 (1 << 8)
#define M2_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
M2_DPLL_DIV_12 | M2_DPLL_MULT_12 | \
MX_APLLS_CLIKIN_12)
/* Speed changes - Used 658.7MHz instead of 660MHz for LP-Refresh M=76 N=2,
* relock time issue */
/* Core frequency changed from 330/165 to 329/164 MHz*/
#define M2_DPLL_MULT_13 (76 << 12)
#define M2_DPLL_DIV_13 (2 << 8)
#define M2_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \
M2_DPLL_DIV_13 | M2_DPLL_MULT_13 | \
MX_APLLS_CLIKIN_13)
#define M2_DPLL_MULT_19 (17 << 12)
#define M2_DPLL_DIV_19 (0 << 8)
#define M2_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \
M2_DPLL_DIV_19 | M2_DPLL_MULT_19 | \
MX_APLLS_CLIKIN_19_2)
/* boot (boot) */
#define MB_DPLL_MULT (1 << 12)
#define MB_DPLL_DIV (0 << 8)
#define MB_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
MB_DPLL_DIV | MB_DPLL_MULT | \
MX_APLLS_CLIKIN_12)
#define MB_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \
MB_DPLL_DIV | MB_DPLL_MULT | \
MX_APLLS_CLIKIN_13)
#define MB_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \
MB_DPLL_DIV | MB_DPLL_MULT | \
MX_APLLS_CLIKIN_19)
/*
* 2430 - chassis (sedna)
* 165 (ratio1) same as above #2
* 150 (ratio1)
* 133 (ratio2) same as above #4
* 110 (ratio2) same as above #3
* 104 (ratio2)
* boot (boot)
*/
/* PRCM I target DPLL = 2*330MHz = 660MHz */
#define MI_DPLL_MULT_12 (55 << 12)
#define MI_DPLL_DIV_12 (1 << 8)
#define MI_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
MI_DPLL_DIV_12 | MI_DPLL_MULT_12 | \
MX_APLLS_CLIKIN_12)
/*
* 2420 Equivalent - mode registers
* PRCM II , target DPLL = 2*300MHz = 600MHz
*/
#define MII_DPLL_MULT_12 (50 << 12)
#define MII_DPLL_DIV_12 (1 << 8)
#define MII_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
MII_DPLL_DIV_12 | MII_DPLL_MULT_12 | \
MX_APLLS_CLIKIN_12)
#define MII_DPLL_MULT_13 (300 << 12)
#define MII_DPLL_DIV_13 (12 << 8)
#define MII_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \
MII_DPLL_DIV_13 | MII_DPLL_MULT_13 | \
MX_APLLS_CLIKIN_13)
/* PRCM III target DPLL = 2*266 = 532MHz*/
#define MIII_DPLL_MULT_12 (133 << 12)
#define MIII_DPLL_DIV_12 (5 << 8)
#define MIII_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \
MIII_DPLL_DIV_12 | \
MIII_DPLL_MULT_12 | MX_APLLS_CLIKIN_12)
#define MIII_DPLL_MULT_13 (266 << 12)
#define MIII_DPLL_DIV_13 (12 << 8)
#define MIII_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \
MIII_DPLL_DIV_13 | \
MIII_DPLL_MULT_13 | MX_APLLS_CLIKIN_13)
/* PRCM VII (boot bypass) */
#define MVII_CM_CLKSEL1_PLL_12_VAL MB_CM_CLKSEL1_PLL_12_VAL
#define MVII_CM_CLKSEL1_PLL_13_VAL MB_CM_CLKSEL1_PLL_13_VAL
/* High and low operation value */
#define MX_CLKSEL2_PLL_2x_VAL (2 << 0)
#define MX_CLKSEL2_PLL_1x_VAL (1 << 0)
/* MPU speed defines */
#define S12M 12000000
#define S13M 13000000
#define S19M 19200000
#define S26M 26000000
#define S100M 100000000
#define S133M 133000000
#define S150M 150000000
#define S164M 164000000
#define S165M 165000000
#define S199M 199000000
#define S200M 200000000
#define S266M 266000000
#define S300M 300000000
#define S329M 329000000
#define S330M 330000000
#define S399M 399000000
#define S400M 400000000
#define S532M 532000000
#define S600M 600000000
#define S658M 658000000
#define S660M 660000000
#define S798M 798000000
extern const struct prcm_config omap2420_rate_table[];
extern const struct prcm_config omap2430_rate_table[];
extern const struct prcm_config *rate_table;
extern const struct prcm_config *curr_prcm_set;
#endif
