/*
* linux/arch/arm/mach-omap1/id.c
*
* OMAP1 CPU identification code
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/serial_8250.h>
#include <linux/serial_reg.h>
#include <linux/clk.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/arch/board.h>
#include <asm/arch/mux.h>
#include <asm/arch/gpio.h>
#include <asm/arch/fpga.h>
#ifdef CONFIG_PM
#include <asm/arch/pm.h>
#endif
static struct clk * uart1_ck = NULL;
static struct clk * uart2_ck = NULL;
static struct clk * uart3_ck = NULL;
static inline unsigned int omap_serial_in(struct plat_serial8250_port *up,
int offset)
{
offset <<= up->regshift;
return (unsigned int)__raw_readb(up->membase + offset);
}
static inline void omap_serial_outp(struct plat_serial8250_port *p, int offset,
int value)
{
offset <<= p->regshift;
__raw_writeb(value, p->membase + offset);
}
/*
* Internal UARTs need to be initialized for the 8250 autoconfig to work
* properly. Note that the TX watermark initialization may not be needed
* once the 8250.c watermark handling code is merged.
*/
static void __init omap_serial_reset(struct plat_serial8250_port *p)
{
omap_serial_outp(p, UART_OMAP_MDR1, 0x07); /* disable UART */
omap_serial_outp(p, UART_OMAP_SCR, 0x08); /* TX watermark */
omap_serial_outp(p, UART_OMAP_MDR1, 0x00); /* enable UART */
if (!cpu_is_omap1510()) {
omap_serial_outp(p, UART_OMAP_SYSC, 0x01);
while (!(omap_serial_in(p, UART_OMAP_SYSC) & 0x01));
}
}
static struct plat_serial8250_port serial_platform_data[] = {
{
.membase = (char*)IO_ADDRESS(OMAP_UART1_BASE),
.mapbase = (unsigned long)OMAP_UART1_BASE,
.irq = INT_UART1,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = OMAP16XX_BASE_BAUD * 16,
},
{
.membase = (char*)IO_ADDRESS(OMAP_UART2_BASE),
.mapbase = (unsigned long)OMAP_UART2_BASE,
.irq = INT_UART2,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = OMAP16XX_BASE_BAUD * 16,
},
{
.membase = (char*)IO_ADDRESS(OMAP_UART3_BASE),
.mapbase = (unsigned long)OMAP_UART3_BASE,
.irq = INT_UART3,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = OMAP16XX_BASE_BAUD * 16,
},
{ },
};
static struct platform_device serial_device = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev = {
.platform_data = serial_platform_data,
},
};
/*
* Note that on Innovator-1510 UART2 pins conflict with USB2.
* By default UART2 does not work on Innovator-1510 if you have
* USB OHCI enabled. To use UART2, you must disable USB2 first.
*/
void __init omap_serial_init(void)
{
int i;
const struct omap_uart_config *info;
if (cpu_is_omap730()) {
serial_platform_data[0].regshift = 0;
serial_platform_data[1].regshift = 0;
serial_platform_data[0].irq = INT_730_UART_MODEM_1;
serial_platform_data[1].irq = INT_730_UART_MODEM_IRDA_2;
}
if (cpu_is_omap1510()) {
serial_platform_data[0].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[1].uartclk = OMAP1510_BASE_BAUD * 16;
serial_platform_data[2].uartclk = OMAP1510_BASE_BAUD * 16;
}
info = omap_get_config(OMAP_TAG_UART, struct omap_uart_config);
if (info == NULL)
return;
for (i = 0; i < OMAP_MAX_NR_PORTS; i++) {
unsigned char reg;
if (!((1 << i) & info->enabled_uarts)) {
serial_platform_data[i].membase = NULL;
serial_platform_data[i].mapbase = 0;
continue;
}
switch (i) {
case 0:
uart1_ck = clk_get(NULL, "uart1_ck");
if (IS_ERR(uart1_ck))
printk("Could not get uart1_ck\n");
else {
clk_enable(uart1_ck);
if (cpu_is_omap1510())
clk_set_rate(uart1_ck, 12000000);
}
if (cpu_is_omap1510()) {
omap_cfg_reg(UART1_TX);
omap_cfg_reg(UART1_RTS);
if (machine_is_omap_innovator()) {
reg = fpga_read(OMAP1510_FPGA_POWER);
reg |= OMAP1510_FPGA_PCR_COM1_EN;
fpga_write(reg, OMAP1510_FPGA_POWER);
udelay(10);
}
}
break;
case 1:
uart2_ck = clk_get(NULL, "uart2_ck");
if (IS_ERR(uart2_ck))
printk("Could not get uart2_ck\n");
else {
clk_enable(uart2_ck);
if (cpu_is_omap1510())
clk_set_rate(uart2_ck, 12000000);
else
clk_set_rate(uart2_ck, 48000000);
}
if (cpu_is_omap1510()) {
omap_cfg_reg(UART2_TX);
omap_cfg_reg(UART2_RTS);
if (machine_is_omap_innovator()) {
reg = fpga_read(OMAP1510_FPGA_POWER);
reg |= OMAP1510_FPGA_PCR_COM2_EN;
fpga_write(reg, OMAP1510_FPGA_POWER);
udelay(10);
}
}
break;
case 2:
uart3_ck = clk_get(NULL, "uart3_ck");
if (IS_ERR(uart3_ck))
printk("Could not get uart3_ck\n");
else {
clk_enable(uart3_ck);
if (cpu_is_omap1510())
clk_set_rate(uart3_ck, 12000000);
}
if (cpu_is_omap1510()) {
omap_cfg_reg(UART3_TX);
omap_cfg_reg(UART3_RX);
}
break;
}
omap_serial_reset(&serial_platform_data[i]);
}
}
#ifdef CONFIG_OMAP_SERIAL_WAKE
static irqreturn_t omap_serial_wake_interrupt(int irq, void *dev_id,
struct pt_regs *regs)
{
/* Need to do something with serial port right after wake-up? */
return IRQ_HANDLED;
}
/*
* Reroutes serial RX lines to GPIO lines for the duration of
* sleep to allow waking up the device from serial port even
* in deep sleep.
*/
void omap_serial_wake_trigger(int enable)
{
if (!cpu_is_omap16xx())
return;
if (uart1_ck != NULL) {
if (enable)
omap_cfg_reg(V14_16XX_GPIO37);
else
omap_cfg_reg(V14_16XX_UART1_RX);
}
if (uart2_ck != NULL) {
if (enable)
omap_cfg_reg(R9_16XX_GPIO18);
else
omap_cfg_reg(R9_16XX_UART2_RX);
}
if (uart3_ck != NULL) {
if (enable)
omap_cfg_reg(L14_16XX_GPIO49);
else
omap_cfg_reg(L14_16XX_UART3_RX);
}
}
static void __init omap_serial_set_port_wakeup(int gpio_nr)
{
int ret;
ret = omap_request_gpio(gpio_nr);
if (ret < 0) {
printk(KERN_ERR "Could not request UART wake GPIO: %i\n",
gpio_nr);
return;
}
omap_set_gpio_direction(gpio_nr, 1);
ret = request_irq(OMAP_GPIO_IRQ(gpio_nr), &omap_serial_wake_interrupt,
SA_TRIGGER_RISING, "serial wakeup", NULL);
if (ret) {
omap_free_gpio(gpio_nr);
printk(KERN_ERR "No interrupt for UART wake GPIO: %i\n",
gpio_nr);
return;
}
enable_irq_wake(OMAP_GPIO_IRQ(gpio_nr));
}
static int __init omap_serial_wakeup_init(void)
{
if (!cpu_is_omap16xx())
return 0;
if (uart1_ck != NULL)
omap_serial_set_port_wakeup(37);
if (uart2_ck != NULL)
omap_serial_set_port_wakeup(18);
if (uart3_ck != NULL)
omap_serial_set_port_wakeup(49);
return 0;
}
late_initcall(omap_serial_wakeup_init);
#endif /* CONFIG_OMAP_SERIAL_WAKE */
static int __init omap_init(void)
{
return platform_device_register(&serial_device);
}
arch_initcall(omap_init);
