/*
* linux/arch/arm/mach-omap1/devices.c
*
* OMAP1 platform device setup/initialization
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <asm/hardware.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include <asm/mach/map.h>
#include <asm/arch/tc.h>
#include <asm/arch/board.h>
#include <asm/arch/mux.h>
#include <asm/arch/gpio.h>
#if defined(CONFIG_OMAP1610_IR) || defined(CONFIG_OMAP161O_IR_MODULE)
static u64 irda_dmamask = 0xffffffff;
static struct platform_device omap1610ir_device = {
.name = "omap1610-ir",
.id = -1,
.dev = {
.dma_mask = &irda_dmamask,
},
};
static void omap_init_irda(void)
{
/* FIXME define and use a boot tag, members something like:
* u8 uart; // uart1, or uart3
* ... but driver only handles uart3 for now
* s16 fir_sel; // gpio for SIR vs FIR
* ... may prefer a callback for SIR/MIR/FIR mode select;
* while h2 uses a GPIO, H3 uses a gpio expander
*/
if (machine_is_omap_h2()
|| machine_is_omap_h3())
(void) platform_device_register(&omap1610ir_device);
}
#else
static inline void omap_init_irda(void) {}
#endif
/*-------------------------------------------------------------------------*/
#if defined(CONFIG_OMAP_RTC) || defined(CONFIG_OMAP_RTC)
#define OMAP_RTC_BASE 0xfffb4800
static struct resource rtc_resources[] = {
{
.start = OMAP_RTC_BASE,
.end = OMAP_RTC_BASE + 0x5f,
.flags = IORESOURCE_MEM,
},
{
.start = INT_RTC_TIMER,
.flags = IORESOURCE_IRQ,
},
{
.start = INT_RTC_ALARM,
.flags = IORESOURCE_IRQ,
},
};
static struct platform_device omap_rtc_device = {
.name = "omap_rtc",
.id = -1,
.num_resources = ARRAY_SIZE(rtc_resources),
.resource = rtc_resources,
};
static void omap_init_rtc(void)
{
(void) platform_device_register(&omap_rtc_device);
}
#else
static inline void omap_init_rtc(void) {}
#endif
#if defined(CONFIG_OMAP_STI)
#define OMAP1_STI_BASE IO_ADDRESS(0xfffea000)
#define OMAP1_STI_CHANNEL_BASE (OMAP1_STI_BASE + 0x400)
static struct resource sti_resources[] = {
{
.start = OMAP1_STI_BASE,
.end = OMAP1_STI_BASE + SZ_1K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = OMAP1_STI_CHANNEL_BASE,
.end = OMAP1_STI_CHANNEL_BASE + SZ_1K - 1,
.flags = IORESOURCE_MEM,
},
{
.start = INT_1610_STI,
.flags = IORESOURCE_IRQ,
}
};
static struct platform_device sti_device = {
.name = "sti",
.id = -1,
.num_resources = ARRAY_SIZE(sti_resources),
.resource = sti_resources,
};
static inline void omap_init_sti(void)
{
platform_device_register(&sti_device);
}
#else
static inline void omap_init_sti(void) {}
#endif
/*-------------------------------------------------------------------------*/
/*
* This gets called after board-specific INIT_MACHINE, and initializes most
* on-chip peripherals accessible on this board (except for few like USB):
*
* (a) Does any "standard config" pin muxing needed. Board-specific
* code will have muxed GPIO pins and done "nonstandard" setup;
* that code could live in the boot loader.
* (b) Populating board-specific platform_data with the data drivers
* rely on to handle wiring variations.
* (c) Creating platform devices as meaningful on this board and
* with this kernel configuration.
*
* Claiming GPIOs, and setting their direction and initial values, is the
* responsibility of the device drivers. So is responding to probe().
*
* Board-specific knowlege like creating devices or pin setup is to be
* kept out of drivers as much as possible. In particular, pin setup
* may be handled by the boot loader, and drivers should expect it will
* normally have been done by the time they're probed.
*/
static int __init omap1_init_devices(void)
{
/* please keep these calls, and their implementations above,
* in alphabetical order so they're easier to sort through.
*/
omap_init_irda();
omap_init_rtc();
omap_init_sti();
return 0;
}
arch_initcall(omap1_init_devices);
