/*
* linux/arch/arm/mach-omap1/board-perseus2.c
*
* Modified from board-generic.c
*
* Original OMAP730 support by Jean Pihet <j-pihet@ti.com>
* Updated for 2.6 by Kevin Hilman <kjh@hilman.org>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <asm/arch/tc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/fpga.h>
#include <asm/arch/common.h>
#include <asm/arch/board.h>
static struct resource smc91x_resources[] = {
[0] = {
.start = H2P2_DBG_FPGA_ETHR_START, /* Physical */
.end = H2P2_DBG_FPGA_ETHR_START + 0xf,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = INT_730_MPU_EXT_NIRQ,
.end = 0,
.flags = IORESOURCE_IRQ,
},
};
static struct mtd_partition p2_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
.name = "bootloader",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* bootloader params in the next sector */
{
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = 0,
},
/* kernel */
{
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
.mask_flags = 0
},
/* rest of flash is a file system */
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0
},
};
static struct flash_platform_data p2_flash_data = {
.map_name = "cfi_probe",
.width = 2,
.parts = p2_partitions,
.nr_parts = ARRAY_SIZE(p2_partitions),
};
static struct resource p2_flash_resource = {
.start = OMAP_CS0_PHYS,
.end = OMAP_CS0_PHYS + SZ_32M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device p2_flash_device = {
.name = "omapflash",
.id = 0,
.dev = {
.platform_data = &p2_flash_data,
},
.num_resources = 1,
.resource = &p2_flash_resource,
};
static struct platform_device smc91x_device = {
.name = "smc91x",
.id = 0,
.num_resources = ARRAY_SIZE(smc91x_resources),
.resource = smc91x_resources,
};
static struct platform_device *devices[] __initdata = {
&p2_flash_device,
&smc91x_device,
};
static struct omap_uart_config perseus2_uart_config __initdata = {
.enabled_uarts = ((1 << 0) | (1 << 1)),
};
static struct omap_lcd_config perseus2_lcd_config __initdata = {
.panel_name = "p2",
.ctrl_name = "internal",
};
static struct omap_board_config_kernel perseus2_config[] = {
{ OMAP_TAG_UART, &perseus2_uart_config },
{ OMAP_TAG_LCD, &perseus2_lcd_config },
};
static void __init omap_perseus2_init(void)
{
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
omap_board_config = perseus2_config;
omap_board_config_size = ARRAY_SIZE(perseus2_config);
omap_serial_init();
}
static void __init perseus2_init_smc91x(void)
{
fpga_write(1, H2P2_DBG_FPGA_LAN_RESET);
mdelay(50);
fpga_write(fpga_read(H2P2_DBG_FPGA_LAN_RESET) & ~1,
H2P2_DBG_FPGA_LAN_RESET);
mdelay(50);
}
void omap_perseus2_init_irq(void)
{
omap_init_irq();
omap_gpio_init();
perseus2_init_smc91x();
}
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_perseus2_io_desc[] __initdata = {
{
.virtual = H2P2_DBG_FPGA_BASE,
.pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
.length = H2P2_DBG_FPGA_SIZE,
.type = MT_DEVICE
}
};
static void __init omap_perseus2_map_io(void)
{
omap_map_common_io();
iotable_init(omap_perseus2_io_desc,
ARRAY_SIZE(omap_perseus2_io_desc));
/* Early, board-dependent init */
/*
* Hold GSM Reset until needed
*/
omap_writew(omap_readw(OMAP730_DSP_M_CTL) & ~1, OMAP730_DSP_M_CTL);
/*
* UARTs -> done automagically by 8250 driver
*/
/*
* CSx timings, GPIO Mux ... setup
*/
/* Flash: CS0 timings setup */
omap_writel(0x0000fff3, OMAP730_FLASH_CFG_0);
omap_writel(0x00000088, OMAP730_FLASH_ACFG_0);
/*
* Ethernet support trough the debug board
* CS1 timings setup
*/
omap_writel(0x0000fff3, OMAP730_FLASH_CFG_1);
omap_writel(0x00000000, OMAP730_FLASH_ACFG_1);
/*
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,
* It is used as the Ethernet controller interrupt
*/
omap_writel(omap_readl(OMAP730_IO_CONF_9) & 0x1FFFFFFF, OMAP730_IO_CONF_9);
}
MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")
/* Maintainer: Kevin Hilman <kjh@hilman.org> */
.phys_ram = 0x10000000,
.phys_io = 0xfff00000,
.io_pg_offst = ((0xfef00000) >> 18) & 0xfffc,
.boot_params = 0x10000100,
.map_io = omap_perseus2_map_io,
.init_irq = omap_perseus2_init_irq,
.init_machine = omap_perseus2_init,
.timer = &omap_timer,
MACHINE_END
