/* lcd-panel.h
written by Marc Singer
18 Jul 2005
Copyright (C) 2005 Marc Singer
-----------
DESCRIPTION
-----------
Only one panel may be defined at a time.
The pixel clock is calculated to be no greater than the target.
Each timing value is accompanied by a specification comment.
UNITS/MIN/TYP/MAX
Most of the units will be in clocks.
USE_RGB555
Define this macro to configure the AMBA LCD controller to use an
RGB555 encoding for the pels instead of the normal RGB565.
LPD9520, LPD79524, LPD7A400, LPD7A404-10, LPD7A404-11
These boards are best approximated by 555 for all panels. Some
can use an extra low-order bit of blue in bit 16 of the color
value, but we don't have a way to communicate this non-linear
mapping to the kernel.
*/
#if !defined (__LCD_PANEL_H__)
# define __LCD_PANEL_H__
#if defined (MACH_LPD79520)\
|| defined (MACH_LPD79524)\
|| defined (MACH_LPD7A400)\
|| defined (MACH_LPD7A404)
# define USE_RGB555
#endif
struct clcd_panel_extra {
unsigned int hrmode;
unsigned int clsen;
unsigned int spsen;
unsigned int pcdel;
unsigned int revdel;
unsigned int lpdel;
unsigned int spldel;
unsigned int pc2del;
};
#define NS_TO_CLOCK(ns,c) ((((ns)*((c)/1000) + (1000000 - 1))/1000000))
#define CLOCK_TO_DIV(e,c) (((c) + (e) - 1)/(e))
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ035Q7DB02_HRTFT
/* Logic Product Development LCD 3.5" QVGA HRTFT -10 */
/* Sharp PN LQ035Q7DB02 w/HRTFT controller chip */
#define PIX_CLOCK_TARGET (6800000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "3.5in QVGA (LQ035Q7DB02)",
.xres = 240,
.yres = 320,
.pixclock = PIX_CLOCK,
.left_margin = 16,
.right_margin = 21,
.upper_margin = 8, // line/8/8/8
.lower_margin = 5,
.hsync_len = 61,
.vsync_len = NS_TO_CLOCK (60, PIX_CLOCK),
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IPC | (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#define HAS_LCD_PANEL_EXTRA
static struct clcd_panel_extra lcd_panel_extra = {
.hrmode = 1,
.clsen = 1,
.spsen = 1,
.pcdel = 8,
.revdel = 7,
.lpdel = 13,
.spldel = 77,
.pc2del = 208,
};
#endif
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ057Q3DC02
/* Logic Product Development LCD 5.7" QVGA -10 */
/* Sharp PN LQ057Q3DC02 */
/* QVGA mode, V/Q=LOW */
/* From Sharp on 2006.1.3. I believe some of the values are incorrect
* based on the datasheet.
Timing0 TIMING1 TIMING2 CONTROL
0x140A0C4C 0x080504EF 0x013F380D 0x00000829
HBP= 20 VBP= 8 BCD= 0
HFP= 10 VFP= 5 CPL=319
HSW= 12 VSW= 1 IOE= 0
PPL= 19 LPP=239 IPC= 1
IHS= 1
IVS= 1
ACB= 0
CSEL= 0
PCD= 13
*/
/* The full horizontal cycle (Th) is clock/360/400/450. */
/* The full vertical cycle (Tv) is line/251/262/280. */
#define PIX_CLOCK_TARGET (6300000) /* -/6.3/7 MHz */
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "5.7in QVGA (LQ057Q3DC02)",
.xres = 320,
.yres = 240,
.pixclock = PIX_CLOCK,
.left_margin = 11,
.right_margin = 400-11-320-2,
.upper_margin = 7, // line/7/7/7
.lower_margin = 262-7-240-2,
.hsync_len = 2, // clk/2/96/200
.vsync_len = 2, // line/2/-/34
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ64D343
/* Logic Product Development LCD 6.4" VGA -10 */
/* Sharp PN LQ64D343 */
/* The full horizontal cycle (Th) is clock/750/800/900. */
/* The full vertical cycle (Tv) is line/515/525/560. */
#define PIX_CLOCK_TARGET (28330000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "6.4in QVGA (LQ64D343)",
.xres = 640,
.yres = 480,
.pixclock = PIX_CLOCK,
.left_margin = 32,
.right_margin = 800-32-640-96,
.upper_margin = 32, // line/34/34/34
.lower_margin = 540-32-480-2,
.hsync_len = 96, // clk/2/96/200
.vsync_len = 2, // line/2/-/34
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ10D368
/* Logic Product Development LCD 10.4" VGA -10 */
/* Sharp PN LQ10D368 */
#define PIX_CLOCK_TARGET (28330000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "10.4in VGA (LQ10D368)",
.xres = 640,
.yres = 480,
.pixclock = PIX_CLOCK,
.left_margin = 21,
.right_margin = 15,
.upper_margin = 34,
.lower_margin = 5,
.hsync_len = 96,
.vsync_len = 16,
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_SHARP_LQ121S1DG41
/* Logic Product Development LCD 12.1" SVGA -10 */
/* Sharp PN LQ121S1DG41, was LQ121S1DG31 */
/* Note that with a 99993900 Hz HCLK, it is not possible to hit the
* target clock frequency range of 35MHz to 42MHz. */
/* If the target pixel clock is substantially lower than the panel
* spec, this is done to prevent the LCD display from glitching when
* the CPU is under load. A pixel clock higher than 25MHz
* (empirically determined) will compete with the CPU for bus cycles
* for the Ethernet chip. However, even a pixel clock of 10MHz
* competes with Compact Flash interface during some operations
* (fdisk, e2fsck). And, at that speed the display may have a visible
* flicker. */
/* The full horizontal cycle (Th) is clock/832/1056/1395. */
#define PIX_CLOCK_TARGET (20000000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "12.1in SVGA (LQ121S1DG41)",
.xres = 800,
.yres = 600,
.pixclock = PIX_CLOCK,
.left_margin = 89, // ns/5/-/(1/PIX_CLOCK)-10
.right_margin = 1056-800-89-128,
.upper_margin = 23, // line/23/23/23
.lower_margin = 44,
.hsync_len = 128, // clk/2/128/200
.vsync_len = 4, // line/2/4/6
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_HITACHI
/* Hitachi*/
/* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
#define PIX_CLOCK_TARGET (49000000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "Hitachi 800x480",
.xres = 800,
.yres = 480,
.pixclock = PIX_CLOCK,
.left_margin = 88,
.right_margin = 40,
.upper_margin = 32,
.lower_margin = 11,
.hsync_len = 128,
.vsync_len = 2,
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#if defined CONFIG_FB_ARMCLCD_AUO_A070VW01_WIDE
/* AU Optotronics A070VW01 7.0 Wide Screen color Display*/
/* Submitted by Michele Da Rold <michele.darold@ecsproject.com> */
#define PIX_CLOCK_TARGET (10000000)
#define PIX_CLOCK_DIVIDER CLOCK_TO_DIV (PIX_CLOCK_TARGET, HCLK)
#define PIX_CLOCK (HCLK/PIX_CLOCK_DIVIDER)
static struct clcd_panel lcd_panel = {
.mode = {
.name = "7.0in Wide (A070VW01)",
.xres = 480,
.yres = 234,
.pixclock = PIX_CLOCK,
.left_margin = 30,
.right_margin = 25,
.upper_margin = 14,
.lower_margin = 12,
.hsync_len = 100,
.vsync_len = 1,
.vmode = FB_VMODE_NONINTERLACED,
},
.width = -1,
.height = -1,
.tim2 = TIM2_IPC | TIM2_IHS | TIM2_IVS
| (PIX_CLOCK_DIVIDER - 2),
.cntl = CNTL_LCDTFT | CNTL_WATERMARK,
.bpp = 16,
};
#endif
#undef NS_TO_CLOCK
#undef CLOCK_TO_DIV
#endif /* __LCD_PANEL_H__ */
