/*
* arch/arm/mach-ixp4xx/nslu2-setup.c
*
* NSLU2 board-setup
*
* Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
*
* based on ixdp425-setup.c:
* Copyright (C) 2003-2004 MontaVista Software, Inc.
* based on nslu2-power.c:
* Copyright (C) 2005 Tower Technologies
*
* Author: Mark Rakes <mrakes at mac.com>
* Author: Rod Whitby <rod@whitby.id.au>
* Author: Alessandro Zummo <a.zummo@towertech.it>
* Maintainers: http://www.nslu2-linux.org/
*
*/
#include <linux/gpio.h>
#include <linux/if_ether.h>
#include <linux/irq.h>
#include <linux/serial.h>
#include <linux/serial_8250.h>
#include <linux/leds.h>
#include <linux/reboot.h>
#include <linux/i2c.h>
#include <linux/i2c-gpio.h>
#include <linux/io.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/time.h>
#define NSLU2_SDA_PIN 7
#define NSLU2_SCL_PIN 6
/* NSLU2 Timer */
#define NSLU2_FREQ 66000000
/* Buttons */
#define NSLU2_PB_GPIO 5 /* power button */
#define NSLU2_PO_GPIO 8 /* power off */
#define NSLU2_RB_GPIO 12 /* reset button */
/* Buzzer */
#define NSLU2_GPIO_BUZZ 4
/* LEDs */
#define NSLU2_LED_RED_GPIO 0
#define NSLU2_LED_GRN_GPIO 1
#define NSLU2_LED_DISK1_GPIO 3
#define NSLU2_LED_DISK2_GPIO 2
static struct flash_platform_data nslu2_flash_data = {
.map_name = "cfi_probe",
.width = 2,
};
static struct resource nslu2_flash_resource = {
.flags = IORESOURCE_MEM,
};
static struct platform_device nslu2_flash = {
.name = "IXP4XX-Flash",
.id = 0,
.dev.platform_data = &nslu2_flash_data,
.num_resources = 1,
.resource = &nslu2_flash_resource,
};
static struct i2c_gpio_platform_data nslu2_i2c_gpio_data = {
.sda_pin = NSLU2_SDA_PIN,
.scl_pin = NSLU2_SCL_PIN,
};
static struct i2c_board_info __initdata nslu2_i2c_board_info [] = {
{
I2C_BOARD_INFO("x1205", 0x6f),
},
};
static struct gpio_led nslu2_led_pins[] = {
{
.name = "nslu2:green:ready",
.gpio = NSLU2_LED_GRN_GPIO,
},
{
.name = "nslu2:red:status",
.gpio = NSLU2_LED_RED_GPIO,
},
{
.name = "nslu2:green:disk-1",
.gpio = NSLU2_LED_DISK1_GPIO,
.active_low = true,
},
{
.name = "nslu2:green:disk-2",
.gpio = NSLU2_LED_DISK2_GPIO,
.active_low = true,
},
};
static struct gpio_led_platform_data nslu2_led_data = {
.num_leds = ARRAY_SIZE(nslu2_led_pins),
.leds = nslu2_led_pins,
};
static struct platform_device nslu2_leds = {
.name = "leds-gpio",
.id = -1,
.dev.platform_data = &nslu2_led_data,
};
static struct platform_device nslu2_i2c_gpio = {
.name = "i2c-gpio",
.id = 0,
.dev = {
.platform_data = &nslu2_i2c_gpio_data,
},
};
static struct platform_device nslu2_beeper = {
.name = "ixp4xx-beeper",
.id = NSLU2_GPIO_BUZZ,
.num_resources = 0,
};
static struct resource nslu2_uart_resources[] = {
{
.start = IXP4XX_UART1_BASE_PHYS,
.end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
},
{
.start = IXP4XX_UART2_BASE_PHYS,
.end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
.flags = IORESOURCE_MEM,
}
};
static struct plat_serial8250_port nslu2_uart_data[] = {
{
.mapbase = IXP4XX_UART1_BASE_PHYS,
.membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART1,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{
.mapbase = IXP4XX_UART2_BASE_PHYS,
.membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
.irq = IRQ_IXP4XX_UART2,
.flags = UPF_BOOT_AUTOCONF,
.iotype = UPIO_MEM,
.regshift = 2,
.uartclk = IXP4XX_UART_XTAL,
},
{ }
};
static struct platform_device nslu2_uart = {
.name = "serial8250",
.id = PLAT8250_DEV_PLATFORM,
.dev.platform_data = nslu2_uart_data,
.num_resources = 2,
.resource = nslu2_uart_resources,
};
/* Built-in 10/100 Ethernet MAC interfaces */
static struct eth_plat_info nslu2_plat_eth[] = {
{
.phy = 1,
.rxq = 3,
.txreadyq = 20,
}
};
static struct platform_device nslu2_eth[] = {
{
.name = "ixp4xx_eth",
.id = IXP4XX_ETH_NPEB,
.dev.platform_data = nslu2_plat_eth,
}
};
static struct platform_device *nslu2_devices[] __initdata = {
&nslu2_i2c_gpio,
&nslu2_flash,
&nslu2_beeper,
&nslu2_leds,
&nslu2_eth[0],
};
static void nslu2_power_off(void)
{
/* This causes the box to drop the power and go dead. */
/* enable the pwr cntl gpio */
gpio_line_config(NSLU2_PO_GPIO, IXP4XX_GPIO_OUT);
/* do the deed */
gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH);
}
static irqreturn_t nslu2_power_handler(int irq, void *dev_id)
{
/* Signal init to do the ctrlaltdel action, this will bypass init if
* it hasn't started and do a kernel_restart.
*/
ctrl_alt_del();
return IRQ_HANDLED;
}
static irqreturn_t nslu2_reset_handler(int irq, void *dev_id)
{
/* This is the paper-clip reset, it shuts the machine down directly.
*/
machine_power_off();
return IRQ_HANDLED;
}
static void __init nslu2_timer_init(void)
{
/* The xtal on this machine is non-standard. */
ixp4xx_timer_freq = NSLU2_FREQ;
/* Call standard timer_init function. */
ixp4xx_timer_init();
}
static struct sys_timer nslu2_timer = {
.init = nslu2_timer_init,
};
static void __init nslu2_init(void)
{
uint8_t __iomem *f;
int i;
ixp4xx_sys_init();
nslu2_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
nslu2_flash_resource.end =
IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
i2c_register_board_info(0, nslu2_i2c_board_info,
ARRAY_SIZE(nslu2_i2c_board_info));
/*
* This is only useful on a modified machine, but it is valuable
* to have it first in order to see debug messages, and so that
* it does *not* get removed if platform_add_devices fails!
*/
(void)platform_device_register(&nslu2_uart);
platform_add_devices(nslu2_devices, ARRAY_SIZE(nslu2_devices));
pm_power_off = nslu2_power_off;
if (request_irq(gpio_to_irq(NSLU2_RB_GPIO), &nslu2_reset_handler,
IRQF_DISABLED | IRQF_TRIGGER_LOW,
"NSLU2 reset button", NULL) < 0) {
printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
gpio_to_irq(NSLU2_RB_GPIO));
}
if (request_irq(gpio_to_irq(NSLU2_PB_GPIO), &nslu2_power_handler,
IRQF_DISABLED | IRQF_TRIGGER_HIGH,
"NSLU2 power button", NULL) < 0) {
printk(KERN_DEBUG "Power Button IRQ %d not available\n",
gpio_to_irq(NSLU2_PB_GPIO));
}
/*
* Map in a portion of the flash and read the MAC address.
* Since it is stored in BE in the flash itself, we need to
* byteswap it if we're in LE mode.
*/
f = ioremap(IXP4XX_EXP_BUS_BASE(0), 0x40000);
if (f) {
for (i = 0; i < 6; i++)
#ifdef __ARMEB__
nslu2_plat_eth[0].hwaddr[i] = readb(f + 0x3FFB0 + i);
#else
nslu2_plat_eth[0].hwaddr[i] = readb(f + 0x3FFB0 + (i^3));
#endif
iounmap(f);
}
printk(KERN_INFO "NSLU2: Using MAC address %pM for port 0\n",
nslu2_plat_eth[0].hwaddr);
}
MACHINE_START(NSLU2, "Linksys NSLU2")
/* Maintainer: www.nslu2-linux.org */
.atag_offset = 0x100,
.map_io = ixp4xx_map_io,
.init_irq = ixp4xx_init_irq,
.timer = &nslu2_timer,
.init_machine = nslu2_init,
#if defined(CONFIG_PCI)
.dma_zone_size = SZ_64M,
#endif
.restart = ixp4xx_restart,
MACHINE_END
