/*
* TI DA830/OMAP L137 EVM board
*
* Author: Mark A. Greer <mgreer@mvista.com>
* Derived from: arch/arm/mach-davinci/board-dm644x-evm.c
*
* 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
* the terms of the GNU General Public License version 2. This program
* is licensed "as is" without any warranty of any kind, whether express
* or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/console.h>
#include <linux/interrupt.h>
#include <linux/gpio.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/i2c/pcf857x.h>
#include <linux/i2c/at24.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/cp_intc.h>
#include <mach/mux.h>
#include <mach/nand.h>
#include <mach/da8xx.h>
#include <mach/usb.h>
#include <mach/aemif.h>
#define DA830_EVM_PHY_ID ""
/*
* USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4].
*/
#define ON_BD_USB_DRV GPIO_TO_PIN(1, 15)
#define ON_BD_USB_OVC GPIO_TO_PIN(2, 4)
static const short da830_evm_usb11_pins[] = {
DA830_GPIO1_15, DA830_GPIO2_4,
-1
};
static da8xx_ocic_handler_t da830_evm_usb_ocic_handler;
static int da830_evm_usb_set_power(unsigned port, int on)
{
gpio_set_value(ON_BD_USB_DRV, on);
return 0;
}
static int da830_evm_usb_get_power(unsigned port)
{
return gpio_get_value(ON_BD_USB_DRV);
}
static int da830_evm_usb_get_oci(unsigned port)
{
return !gpio_get_value(ON_BD_USB_OVC);
}
static irqreturn_t da830_evm_usb_ocic_irq(int, void *);
static int da830_evm_usb_ocic_notify(da8xx_ocic_handler_t handler)
{
int irq = gpio_to_irq(ON_BD_USB_OVC);
int error = 0;
if (handler != NULL) {
da830_evm_usb_ocic_handler = handler;
error = request_irq(irq, da830_evm_usb_ocic_irq, IRQF_DISABLED |
IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
"OHCI over-current indicator", NULL);
if (error)
printk(KERN_ERR "%s: could not request IRQ to watch "
"over-current indicator changes\n", __func__);
} else
free_irq(irq, NULL);
return error;
}
static struct da8xx_ohci_root_hub da830_evm_usb11_pdata = {
.set_power = da830_evm_usb_set_power,
.get_power = da830_evm_usb_get_power,
.get_oci = da830_evm_usb_get_oci,
.ocic_notify = da830_evm_usb_ocic_notify,
/* TPS2065 switch @ 5V */
.potpgt = (3 + 1) / 2, /* 3 ms max */
};
static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id)
{
da830_evm_usb_ocic_handler(&da830_evm_usb11_pdata, 1);
return IRQ_HANDLED;
}
static __init void da830_evm_usb_init(void)
{
u32 cfgchip2;
int ret;
/*
* Set up USB clock/mode in the CFGCHIP2 register.
* FYI: CFGCHIP2 is 0x0000ef00 initially.
*/
cfgchip2 = __raw_readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
/* USB2.0 PHY reference clock is 24 MHz */
cfgchip2 &= ~CFGCHIP2_REFFREQ;
cfgchip2 |= CFGCHIP2_REFFREQ_24MHZ;
/*
* Select internal reference clock for USB 2.0 PHY
* and use it as a clock source for USB 1.1 PHY
* (this is the default setting anyway).
*/
cfgchip2 &= ~CFGCHIP2_USB1PHYCLKMUX;
cfgchip2 |= CFGCHIP2_USB2PHYCLKMUX;
/*
* We have to override VBUS/ID signals when MUSB is configured into the
* host-only mode -- ID pin will float if no cable is connected, so the
* controller won't be able to drive VBUS thinking that it's a B-device.
* Otherwise, we want to use the OTG mode and enable VBUS comparators.
*/
cfgchip2 &= ~CFGCHIP2_OTGMODE;
#ifdef CONFIG_USB_MUSB_HOST
cfgchip2 |= CFGCHIP2_FORCE_HOST;
#else
cfgchip2 |= CFGCHIP2_SESENDEN | CFGCHIP2_VBDTCTEN;
#endif
__raw_writel(cfgchip2, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
/* USB_REFCLKIN is not used. */
ret = davinci_cfg_reg(DA830_USB0_DRVVBUS);
if (ret)
pr_warning("%s: USB 2.0 PinMux setup failed: %d\n",
__func__, ret);
else {
/*
* TPS2065 switch @ 5V supplies 1 A (sustains 1.5 A),
* with the power on to power good time of 3 ms.
*/
ret = da8xx_register_usb20(1000, 3);
if (ret)
pr_warning("%s: USB 2.0 registration failed: %d\n",
__func__, ret);
}
ret = davinci_cfg_reg_list(da830_evm_usb11_pins);
if (ret) {
pr_warning("%s: USB 1.1 PinMux setup failed: %d\n",
__func__, ret);
return;
}
ret = gpio_request(ON_BD_USB_DRV, "ON_BD_USB_DRV");
if (ret) {
printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
"power control: %d\n", __func__, ret);
return;
}
gpio_direction_output(ON_BD_USB_DRV, 0);
ret = gpio_request(ON_BD_USB_OVC, "ON_BD_USB_OVC");
if (ret) {
printk(KERN_ERR "%s: failed to request GPIO for USB 1.1 port "
"over-current indicator: %d\n", __func__, ret);
return;
}
gpio_direction_input(ON_BD_USB_OVC);
ret = da8xx_register_usb11(&da830_evm_usb11_pdata);
if (ret)
pr_warning("%s: USB 1.1 registration failed: %d\n",
__func__, ret);
}
static struct davinci_uart_config da830_evm_uart_config __initdata = {
.enabled_uarts = 0x7,
};
static const short da830_evm_mcasp1_pins[] = {
DA830_AHCLKX1, DA830_ACLKX1, DA830_AFSX1, DA830_AHCLKR1, DA830_AFSR1,
DA830_AMUTE1, DA830_AXR1_0, DA830_AXR1_1, DA830_AXR1_2, DA830_AXR1_5,
DA830_ACLKR1, DA830_AXR1_6, DA830_AXR1_7, DA830_AXR1_8, DA830_AXR1_10,
DA830_AXR1_11,
-1
};
static u8 da830_iis_serializer_direction[] = {
RX_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
INACTIVE_MODE, TX_MODE, INACTIVE_MODE, INACTIVE_MODE,
INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE, INACTIVE_MODE,
};
static struct snd_platform_data da830_evm_snd_data = {
.tx_dma_offset = 0x2000,
.rx_dma_offset = 0x2000,
.op_mode = DAVINCI_MCASP_IIS_MODE,
.num_serializer = ARRAY_SIZE(da830_iis_serializer_direction),
.tdm_slots = 2,
.serial_dir = da830_iis_serializer_direction,
.asp_chan_q = EVENTQ_0,
.version = MCASP_VERSION_2,
.txnumevt = 1,
.rxnumevt = 1,
};
/*
* GPIO2[1] is used as MMC_SD_WP and GPIO2[2] as MMC_SD_INS.
*/
static const short da830_evm_mmc_sd_pins[] = {
DA830_MMCSD_DAT_0, DA830_MMCSD_DAT_1, DA830_MMCSD_DAT_2,
DA830_MMCSD_DAT_3, DA830_MMCSD_DAT_4, DA830_MMCSD_DAT_5,
DA830_MMCSD_DAT_6, DA830_MMCSD_DAT_7, DA830_MMCSD_CLK,
DA830_MMCSD_CMD, DA830_GPIO2_1, DA830_GPIO2_2,
-1
};
#define DA830_MMCSD_WP_PIN GPIO_TO_PIN(2, 1)
#define DA830_MMCSD_CD_PIN GPIO_TO_PIN(2, 2)
static int da830_evm_mmc_get_ro(int index)
{
return gpio_get_value(DA830_MMCSD_WP_PIN);
}
static int da830_evm_mmc_get_cd(int index)
{
return !gpio_get_value(DA830_MMCSD_CD_PIN);
}
static struct davinci_mmc_config da830_evm_mmc_config = {
.get_ro = da830_evm_mmc_get_ro,
.get_cd = da830_evm_mmc_get_cd,
.wires = 8,
.max_freq = 50000000,
.caps = MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED,
.version = MMC_CTLR_VERSION_2,
};
static inline void da830_evm_init_mmc(void)
{
int ret;
ret = davinci_cfg_reg_list(da830_evm_mmc_sd_pins);
if (ret) {
pr_warning("da830_evm_init: mmc/sd mux setup failed: %d\n",
ret);
return;
}
ret = gpio_request(DA830_MMCSD_WP_PIN, "MMC WP");
if (ret) {
pr_warning("da830_evm_init: can not open GPIO %d\n",
DA830_MMCSD_WP_PIN);
return;
}
gpio_direction_input(DA830_MMCSD_WP_PIN);
ret = gpio_request(DA830_MMCSD_CD_PIN, "MMC CD\n");
if (ret) {
pr_warning("da830_evm_init: can not open GPIO %d\n",
DA830_MMCSD_CD_PIN);
return;
}
gpio_direction_input(DA830_MMCSD_CD_PIN);
ret = da8xx_register_mmcsd0(&da830_evm_mmc_config);
if (ret) {
pr_warning("da830_evm_init: mmc/sd registration failed: %d\n",
ret);
gpio_free(DA830_MMCSD_WP_PIN);
}
}
/*
* UI board NAND/NOR flashes only use 8-bit data bus.
*/
static const short da830_evm_emif25_pins[] = {
DA830_EMA_D_0, DA830_EMA_D_1, DA830_EMA_D_2, DA830_EMA_D_3,
DA830_EMA_D_4, DA830_EMA_D_5, DA830_EMA_D_6, DA830_EMA_D_7,
DA830_EMA_A_0, DA830_EMA_A_1, DA830_EMA_A_2, DA830_EMA_A_3,
DA830_EMA_A_4, DA830_EMA_A_5, DA830_EMA_A_6, DA830_EMA_A_7,
DA830_EMA_A_8, DA830_EMA_A_9, DA830_EMA_A_10, DA830_EMA_A_11,
DA830_EMA_A_12, DA830_EMA_BA_0, DA830_EMA_BA_1, DA830_NEMA_WE,
DA830_NEMA_CS_2, DA830_NEMA_CS_3, DA830_NEMA_OE, DA830_EMA_WAIT_0,
-1
};
#if defined(CONFIG_MMC_DAVINCI) || defined(CONFIG_MMC_DAVINCI_MODULE)
#define HAS_MMC 1
#else
#define HAS_MMC 0
#endif
#ifdef CONFIG_DA830_UI_NAND
static struct mtd_partition da830_evm_nand_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
[0] = {
.name = "bootloader",
.offset = 0,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* bootloader params in the next sector */
[1] = {
.name = "params",
.offset = MTDPART_OFS_APPEND,
.size = SZ_128K,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
/* kernel */
[2] = {
.name = "kernel",
.offset = MTDPART_OFS_APPEND,
.size = SZ_2M,
.mask_flags = 0,
},
/* file system */
[3] = {
.name = "filesystem",
.offset = MTDPART_OFS_APPEND,
.size = MTDPART_SIZ_FULL,
.mask_flags = 0,
}
};
/* flash bbt decriptors */
static uint8_t da830_evm_nand_bbt_pattern[] = { 'B', 'b', 't', '0' };
static uint8_t da830_evm_nand_mirror_pattern[] = { '1', 't', 'b', 'B' };
static struct nand_bbt_descr da830_evm_nand_bbt_main_descr = {
.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
NAND_BBT_WRITE | NAND_BBT_2BIT |
NAND_BBT_VERSION | NAND_BBT_PERCHIP,
.offs = 2,
.len = 4,
.veroffs = 16,
.maxblocks = 4,
.pattern = da830_evm_nand_bbt_pattern
};
static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = {
.options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE |
NAND_BBT_WRITE | NAND_BBT_2BIT |
NAND_BBT_VERSION | NAND_BBT_PERCHIP,
.offs = 2,
.len = 4,
.veroffs = 16,
.maxblocks = 4,
.pattern = da830_evm_nand_mirror_pattern
};
static struct davinci_aemif_timing da830_evm_nandflash_timing = {
.wsetup = 24,
.wstrobe = 21,
.whold = 14,
.rsetup = 19,
.rstrobe = 50,
.rhold = 0,
.ta = 20,
};
static struct davinci_nand_pdata da830_evm_nand_pdata = {
.parts = da830_evm_nand_partitions,
.nr_parts = ARRAY_SIZE(da830_evm_nand_partitions),
.ecc_mode = NAND_ECC_HW,
.ecc_bits = 4,
.options = NAND_USE_FLASH_BBT,
.bbt_td = &da830_evm_nand_bbt_main_descr,
.bbt_md = &da830_evm_nand_bbt_mirror_descr,
.timing = &da830_evm_nandflash_timing,
};
static struct resource da830_evm_nand_resources[] = {
[0] = { /* First memory resource is NAND I/O window */
.start = DA8XX_AEMIF_CS3_BASE,
.end = DA8XX_AEMIF_CS3_BASE + PAGE_SIZE - 1,
.flags = IORESOURCE_MEM,
},
[1] = { /* Second memory resource is AEMIF control registers */
.start = DA8XX_AEMIF_CTL_BASE,
.end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device da830_evm_nand_device = {
.name = "davinci_nand",
.id = 1,
.dev = {
.platform_data = &da830_evm_nand_pdata,
},
.num_resources = ARRAY_SIZE(da830_evm_nand_resources),
.resource = da830_evm_nand_resources,
};
static inline void da830_evm_init_nand(int mux_mode)
{
int ret;
if (HAS_MMC) {
pr_warning("WARNING: both MMC/SD and NAND are "
"enabled, but they share AEMIF pins.\n"
"\tDisable MMC/SD for NAND support.\n");
return;
}
ret = davinci_cfg_reg_list(da830_evm_emif25_pins);
if (ret)
pr_warning("da830_evm_init: emif25 mux setup failed: %d\n",
ret);
ret = platform_device_register(&da830_evm_nand_device);
if (ret)
pr_warning("da830_evm_init: NAND device not registered.\n");
gpio_direction_output(mux_mode, 1);
}
#else
static inline void da830_evm_init_nand(int mux_mode) { }
#endif
#ifdef CONFIG_DA830_UI_LCD
static inline void da830_evm_init_lcdc(int mux_mode)
{
int ret;
ret = davinci_cfg_reg_list(da830_lcdcntl_pins);
if (ret)
pr_warning("da830_evm_init: lcdcntl mux setup failed: %d\n",
ret);
ret = da8xx_register_lcdc(&sharp_lcd035q3dg01_pdata);
if (ret)
pr_warning("da830_evm_init: lcd setup failed: %d\n", ret);
gpio_direction_output(mux_mode, 0);
}
#else
static inline void da830_evm_init_lcdc(int mux_mode) { }
#endif
static struct at24_platform_data da830_evm_i2c_eeprom_info = {
.byte_len = SZ_256K / 8,
.page_size = 64,
.flags = AT24_FLAG_ADDR16,
.setup = davinci_get_mac_addr,
.context = (void *)0x7f00,
};
static int __init da830_evm_ui_expander_setup(struct i2c_client *client,
int gpio, unsigned ngpio, void *context)
{
gpio_request(gpio + 6, "UI MUX_MODE");
/* Drive mux mode low to match the default without UI card */
gpio_direction_output(gpio + 6, 0);
da830_evm_init_lcdc(gpio + 6);
da830_evm_init_nand(gpio + 6);
return 0;
}
static int da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio,
unsigned ngpio, void *context)
{
gpio_free(gpio + 6);
return 0;
}
static struct pcf857x_platform_data __initdata da830_evm_ui_expander_info = {
.gpio_base = DAVINCI_N_GPIO,
.setup = da830_evm_ui_expander_setup,
.teardown = da830_evm_ui_expander_teardown,
};
static struct i2c_board_info __initdata da830_evm_i2c_devices[] = {
{
I2C_BOARD_INFO("24c256", 0x50),
.platform_data = &da830_evm_i2c_eeprom_info,
},
{
I2C_BOARD_INFO("tlv320aic3x", 0x18),
},
{
I2C_BOARD_INFO("pcf8574", 0x3f),
.platform_data = &da830_evm_ui_expander_info,
},
};
static struct davinci_i2c_platform_data da830_evm_i2c_0_pdata = {
.bus_freq = 100, /* kHz */
.bus_delay = 0, /* usec */
};
/*
* The following EDMA channels/slots are not being used by drivers (for
* example: Timer, GPIO, UART events etc) on da830/omap-l137 EVM, hence
* they are being reserved for codecs on the DSP side.
*/
static const s16 da830_dma_rsv_chans[][2] = {
/* (offset, number) */
{ 8, 2},
{12, 2},
{24, 4},
{30, 2},
{-1, -1}
};
static const s16 da830_dma_rsv_slots[][2] = {
/* (offset, number) */
{ 8, 2},
{12, 2},
{24, 4},
{30, 26},
{-1, -1}
};
static struct edma_rsv_info da830_edma_rsv[] = {
{
.rsv_chans = da830_dma_rsv_chans,
.rsv_slots = da830_dma_rsv_slots,
},
};
static __init void da830_evm_init(void)
{
struct davinci_soc_info *soc_info = &davinci_soc_info;
int ret;
ret = da830_register_edma(da830_edma_rsv);
if (ret)
pr_warning("da830_evm_init: edma registration failed: %d\n",
ret);
ret = davinci_cfg_reg_list(da830_i2c0_pins);
if (ret)
pr_warning("da830_evm_init: i2c0 mux setup failed: %d\n",
ret);
ret = da8xx_register_i2c(0, &da830_evm_i2c_0_pdata);
if (ret)
pr_warning("da830_evm_init: i2c0 registration failed: %d\n",
ret);
da830_evm_usb_init();
soc_info->emac_pdata->rmii_en = 1;
soc_info->emac_pdata->phy_id = DA830_EVM_PHY_ID;
ret = davinci_cfg_reg_list(da830_cpgmac_pins);
if (ret)
pr_warning("da830_evm_init: cpgmac mux setup failed: %d\n",
ret);
ret = da8xx_register_emac();
if (ret)
pr_warning("da830_evm_init: emac registration failed: %d\n",
ret);
ret = da8xx_register_watchdog();
if (ret)
pr_warning("da830_evm_init: watchdog registration failed: %d\n",
ret);
davinci_serial_init(&da830_evm_uart_config);
i2c_register_board_info(1, da830_evm_i2c_devices,
ARRAY_SIZE(da830_evm_i2c_devices));
ret = davinci_cfg_reg_list(da830_evm_mcasp1_pins);
if (ret)
pr_warning("da830_evm_init: mcasp1 mux setup failed: %d\n",
ret);
da8xx_register_mcasp(1, &da830_evm_snd_data);
da830_evm_init_mmc();
ret = da8xx_register_rtc();
if (ret)
pr_warning("da830_evm_init: rtc setup failed: %d\n", ret);
}
#ifdef CONFIG_SERIAL_8250_CONSOLE
static int __init da830_evm_console_init(void)
{
if (!machine_is_davinci_da830_evm())
return 0;
return add_preferred_console("ttyS", 2, "115200");
}
console_initcall(da830_evm_console_init);
#endif
static void __init da830_evm_map_io(void)
{
da830_init();
}
MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM")
.boot_params = (DA8XX_DDR_BASE + 0x100),
.map_io = da830_evm_map_io,
.init_irq = cp_intc_init,
.timer = &davinci_timer,
.init_machine = da830_evm_init,
MACHINE_END
