/*
* linux/arch/arm/mach-at91/board-sam9263ek.c
*
* Copyright (C) 2005 SAN People
* Copyright (C) 2007 Atmel Corporation.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/fb.h>
#include <video/atmel_lcdc.h>
#include <asm/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/arch/board.h>
#include <asm/arch/gpio.h>
#include <asm/arch/at91sam926x_mc.h>
#include "generic.h"
/*
* Serial port configuration.
* 0 .. 2 = USART0 .. USART2
* 3 = DBGU
*/
static struct at91_uart_config __initdata ek_uart_config = {
.console_tty = 0, /* ttyS0 */
.nr_tty = 2,
.tty_map = { 3, 0, -1, -1, } /* ttyS0, ..., ttyS3 */
};
static void __init ek_map_io(void)
{
/* Initialize processor: 16.367 MHz crystal */
at91sam9263_initialize(16367660);
/* Setup the serial ports and console */
at91_init_serial(&ek_uart_config);
}
static void __init ek_init_irq(void)
{
at91sam9263_init_interrupts(NULL);
}
/*
* USB Host port
*/
static struct at91_usbh_data __initdata ek_usbh_data = {
.ports = 2,
.vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
};
/*
* USB Device port
*/
static struct at91_udc_data __initdata ek_udc_data = {
.vbus_pin = AT91_PIN_PA25,
.pullup_pin = 0, /* pull-up driven by UDC */
};
/*
* ADS7846 Touchscreen
*/
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
static int ads7843_pendown_state(void)
{
return !at91_get_gpio_value(AT91_PIN_PA15); /* Touchscreen PENIRQ */
}
static struct ads7846_platform_data ads_info = {
.model = 7843,
.x_min = 150,
.x_max = 3830,
.y_min = 190,
.y_max = 3830,
.vref_delay_usecs = 100,
.x_plate_ohms = 450,
.y_plate_ohms = 250,
.pressure_max = 15000,
.debounce_max = 1,
.debounce_rep = 0,
.debounce_tol = (~0),
.get_pendown_state = ads7843_pendown_state,
};
static void __init ek_add_device_ts(void)
{
at91_set_B_periph(AT91_PIN_PA15, 1); /* External IRQ1, with pullup */
at91_set_gpio_input(AT91_PIN_PA31, 1); /* Touchscreen BUSY signal */
}
#else
static void __init ek_add_device_ts(void) {}
#endif
/*
* SPI devices.
*/
static struct spi_board_info ek_spi_devices[] = {
#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
{ /* DataFlash card */
.modalias = "mtd_dataflash",
.chip_select = 0,
.max_speed_hz = 15 * 1000 * 1000,
.bus_num = 0,
},
#endif
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
{
.modalias = "ads7846",
.chip_select = 3,
.max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
.bus_num = 0,
.platform_data = &ads_info,
.irq = AT91SAM9263_ID_IRQ1,
},
#endif
};
/*
* MCI (SD/MMC)
*/
static struct at91_mmc_data __initdata ek_mmc_data = {
.wire4 = 1,
.det_pin = AT91_PIN_PE18,
.wp_pin = AT91_PIN_PE19,
// .vcc_pin = ... not connected
};
/*
* MACB Ethernet device
*/
static struct at91_eth_data __initdata ek_macb_data = {
.phy_irq_pin = AT91_PIN_PE31,
.is_rmii = 1,
};
/*
* NAND flash
*/
static struct mtd_partition __initdata ek_nand_partition[] = {
{
.name = "Partition 1",
.offset = 0,
.size = 64 * 1024 * 1024,
},
{
.name = "Partition 2",
.offset = 64 * 1024 * 1024,
.size = MTDPART_SIZ_FULL,
},
};
static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(ek_nand_partition);
return ek_nand_partition;
}
static struct at91_nand_data __initdata ek_nand_data = {
.ale = 21,
.cle = 22,
// .det_pin = ... not connected
.rdy_pin = AT91_PIN_PA22,
.enable_pin = AT91_PIN_PD15,
.partition_info = nand_partitions,
#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
.bus_width_16 = 1,
#else
.bus_width_16 = 0,
#endif
};
/*
* LCD Controller
*/
#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
static struct fb_videomode at91_tft_vga_modes[] = {
{
.name = "TX09D50VM1CCA @ 60",
.refresh = 60,
.xres = 240, .yres = 320,
.pixclock = KHZ2PICOS(4965),
.left_margin = 1, .right_margin = 33,
.upper_margin = 1, .lower_margin = 0,
.hsync_len = 5, .vsync_len = 1,
.sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
.vmode = FB_VMODE_NONINTERLACED,
},
};
static struct fb_monspecs at91fb_default_monspecs = {
.manufacturer = "HIT",
.monitor = "TX09D70VM1CCA",
.modedb = at91_tft_vga_modes,
.modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
.hfmin = 15000,
.hfmax = 64000,
.vfmin = 50,
.vfmax = 150,
};
#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
| ATMEL_LCDC_DISTYPE_TFT \
| ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
static void at91_lcdc_power_control(int on)
{
if (on)
at91_set_gpio_value(AT91_PIN_PD12, 0); /* power up */
else
at91_set_gpio_value(AT91_PIN_PD12, 1); /* power down */
}
/* Driver datas */
static struct atmel_lcdfb_info __initdata ek_lcdc_data = {
.default_bpp = 16,
.default_dmacon = ATMEL_LCDC_DMAEN,
.default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
.default_monspecs = &at91fb_default_monspecs,
.atmel_lcdfb_power_control = at91_lcdc_power_control,
.guard_time = 1,
};
#else
static struct atmel_lcdfb_info __initdata ek_lcdc_data;
#endif
/*
* AC97
*/
static struct atmel_ac97_data ek_ac97_data = {
.reset_pin = AT91_PIN_PA13,
};
static void __init ek_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* USB Host */
at91_add_device_usbh(&ek_usbh_data);
/* USB Device */
at91_add_device_udc(&ek_udc_data);
/* SPI */
at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
/* Touchscreen */
ek_add_device_ts();
/* MMC */
at91_add_device_mmc(1, &ek_mmc_data);
/* Ethernet */
at91_add_device_eth(&ek_macb_data);
/* NAND */
at91_add_device_nand(&ek_nand_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* LCD Controller */
at91_add_device_lcdc(&ek_lcdc_data);
/* AC97 */
at91_add_device_ac97(&ek_ac97_data);
}
MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
/* Maintainer: Atmel */
.phys_io = AT91_BASE_SYS,
.io_pg_offst = (AT91_VA_BASE_SYS >> 18) & 0xfffc,
.boot_params = AT91_SDRAM_BASE + 0x100,
.timer = &at91sam926x_timer,
.map_io = ek_map_io,
.init_irq = ek_init_irq,
.init_machine = ek_board_init,
MACHINE_END
