/*
* Setup code for SAMA5 Evaluation Kits with Device Tree support
*
* Copyright (C) 2013 Atmel,
* 2013 Ludovic Desroches <ludovic.desroches@atmel.com>
*
* Licensed under GPLv2 or later.
*/
#include <linux/types.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/gpio.h>
#include <linux/micrel_phy.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/phy.h>
#include <linux/clk-provider.h>
#include <asm/setup.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include "at91_aic.h"
#include "generic.h"
static void __init sama5_dt_timer_init(void)
{
#if defined(CONFIG_COMMON_CLK)
of_clk_init(NULL);
#endif
at91sam926x_pit_init();
}
static const struct of_device_id irq_of_match[] __initconst = {
{ .compatible = "atmel,sama5d3-aic", .data = at91_aic5_of_init },
{ /*sentinel*/ }
};
static void __init at91_dt_init_irq(void)
{
of_irq_init(irq_of_match);
}
static int ksz9021rn_phy_fixup(struct phy_device *phy)
{
int value;
/* Set delay values */
value = MICREL_KSZ9021_RGMII_CLK_CTRL_PAD_SCEW | 0x8000;
phy_write(phy, MICREL_KSZ9021_EXTREG_CTRL, value);
value = 0xF2F4;
phy_write(phy, MICREL_KSZ9021_EXTREG_DATA_WRITE, value);
value = MICREL_KSZ9021_RGMII_RX_DATA_PAD_SCEW | 0x8000;
phy_write(phy, MICREL_KSZ9021_EXTREG_CTRL, value);
value = 0x2222;
phy_write(phy, MICREL_KSZ9021_EXTREG_DATA_WRITE, value);
return 0;
}
static void __init sama5_dt_device_init(void)
{
if (of_machine_is_compatible("atmel,sama5d3xcm") &&
IS_ENABLED(CONFIG_PHYLIB))
phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
ksz9021rn_phy_fixup);
of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
}
static const char *sama5_dt_board_compat[] __initdata = {
"atmel,sama5",
NULL
};
DT_MACHINE_START(sama5_dt, "Atmel SAMA5 (Device Tree)")
/* Maintainer: Atmel */
.init_time = sama5_dt_timer_init,
.map_io = at91_map_io,
.handle_irq = at91_aic5_handle_irq,
.init_early = at91_dt_initialize,
.init_irq = at91_dt_init_irq,
.init_machine = sama5_dt_device_init,
.dt_compat = sama5_dt_board_compat,
MACHINE_END
