/*
* linux/arch/arm/mach-at91/board-cpuat91.c
*
* Copyright (C) 2009 Eric Benard - eric@eukrea.com
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/types.h>
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/plat-ram.h>
#include <mach/hardware.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/irq.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/board.h>
#include <mach/at91rm9200_mc.h>
#include <mach/cpu.h>
#include "generic.h"
static struct gpio_led cpuat91_leds[] = {
{
.name = "led1",
.default_trigger = "heartbeat",
.active_low = 1,
.gpio = AT91_PIN_PC0,
},
};
static void __init cpuat91_init_early(void)
{
/* Set cpu type: PQFP */
at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
/* Initialize processor: 18.432 MHz crystal */
at91_initialize(18432000);
/* DBGU on ttyS0. (Rx & Tx only) */
at91_register_uart(0, 0, 0);
/* USART0 on ttyS1. (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91RM9200_ID_US0, 1, ATMEL_UART_CTS |
ATMEL_UART_RTS);
/* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS |
ATMEL_UART_RTS | ATMEL_UART_DTR | ATMEL_UART_DSR |
ATMEL_UART_DCD | ATMEL_UART_RI);
/* USART2 on ttyS3 (Rx, Tx) */
at91_register_uart(AT91RM9200_ID_US2, 3, 0);
/* USART3 on ttyS4 (Rx, Tx, CTS, RTS) */
at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_CTS |
ATMEL_UART_RTS);
/* set serial console to ttyS0 (ie, DBGU) */
at91_set_serial_console(0);
}
static struct macb_platform_data __initdata cpuat91_eth_data = {
.phy_irq_pin = -EINVAL,
.is_rmii = 1,
};
static struct at91_usbh_data __initdata cpuat91_usbh_data = {
.ports = 1,
.vbus_pin = {-EINVAL, -EINVAL},
.overcurrent_pin= {-EINVAL, -EINVAL},
};
static struct at91_udc_data __initdata cpuat91_udc_data = {
.vbus_pin = AT91_PIN_PC15,
.pullup_pin = AT91_PIN_PC14,
};
static struct at91_mmc_data __initdata cpuat91_mmc_data = {
.det_pin = AT91_PIN_PC2,
.wire4 = 1,
.wp_pin = -EINVAL,
.vcc_pin = -EINVAL,
};
static struct physmap_flash_data cpuat91_flash_data = {
.width = 2,
};
static struct resource cpuat91_flash_resource = {
.start = AT91_CHIPSELECT_0,
.end = AT91_CHIPSELECT_0 + SZ_16M - 1,
.flags = IORESOURCE_MEM,
};
static struct platform_device cpuat91_norflash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &cpuat91_flash_data,
},
.resource = &cpuat91_flash_resource,
.num_resources = 1,
};
#ifdef CONFIG_MTD_PLATRAM
struct platdata_mtd_ram at91_sram_pdata = {
.mapname = "SRAM",
.bankwidth = 2,
};
static struct resource at91_sram_resource[] = {
[0] = {
.start = AT91RM9200_SRAM_BASE,
.end = AT91RM9200_SRAM_BASE + AT91RM9200_SRAM_SIZE - 1,
.flags = IORESOURCE_MEM,
},
};
static struct platform_device at91_sram = {
.name = "mtd-ram",
.id = 0,
.resource = at91_sram_resource,
.num_resources = ARRAY_SIZE(at91_sram_resource),
.dev = {
.platform_data = &at91_sram_pdata,
},
};
#endif /* MTD_PLATRAM */
static struct platform_device *platform_devices[] __initdata = {
&cpuat91_norflash,
#ifdef CONFIG_MTD_PLATRAM
&at91_sram,
#endif /* CONFIG_MTD_PLATRAM */
};
static void __init cpuat91_board_init(void)
{
/* Serial */
at91_add_device_serial();
/* LEDs. */
at91_gpio_leds(cpuat91_leds, ARRAY_SIZE(cpuat91_leds));
/* Ethernet */
at91_add_device_eth(&cpuat91_eth_data);
/* USB Host */
at91_add_device_usbh(&cpuat91_usbh_data);
/* USB Device */
at91_add_device_udc(&cpuat91_udc_data);
/* MMC */
at91_add_device_mmc(0, &cpuat91_mmc_data);
/* I2C */
at91_add_device_i2c(NULL, 0);
/* Platform devices */
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
}
MACHINE_START(CPUAT91, "Eukrea")
/* Maintainer: Eric Benard - EUKREA Electromatique */
.timer = &at91rm9200_timer,
.map_io = at91_map_io,
.init_early = cpuat91_init_early,
.init_irq = at91_init_irq_default,
.init_machine = cpuat91_board_init,
MACHINE_END
