#
# For a description of the syntax of this configuration file,
# see Documentation/kbuild/kconfig-language.txt.
#
mainmenu "Linux Kernel Configuration"
config ARM
bool
default y
help
The ARM series is a line of low-power-consumption RISC chip designs
licensed by ARM ltd and targeted at embedded applications and
handhelds such as the Compaq IPAQ. ARM-based PCs are no longer
manufactured, but legacy ARM-based PC hardware remains popular in
Europe. There is an ARM Linux project with a web page at
<http://www.arm.linux.org.uk/>.
config MMU
bool
default y
config EISA
bool
---help---
The Extended Industry Standard Architecture (EISA) bus was
developed as an open alternative to the IBM MicroChannel bus.
The EISA bus provided some of the features of the IBM MicroChannel
bus while maintaining backward compatibility with cards made for
the older ISA bus. The EISA bus saw limited use between 1988 and
1995 when it was made obsolete by the PCI bus.
Say Y here if you are building a kernel for an EISA-based machine.
Otherwise, say N.
config SBUS
bool
config MCA
bool
help
MicroChannel Architecture is found in some IBM PS/2 machines and
laptops. It is a bus system similar to PCI or ISA. See
<file:Documentation/mca.txt> (and especially the web page given
there) before attempting to build an MCA bus kernel.
config UID16
bool
default y
config RWSEM_GENERIC_SPINLOCK
bool
default y
config RWSEM_XCHGADD_ALGORITHM
bool
config GENERIC_CALIBRATE_DELAY
bool
default y
config GENERIC_BUST_SPINLOCK
bool
config ARCH_MAY_HAVE_PC_FDC
bool
config GENERIC_ISA_DMA
bool
config FIQ
bool
source "init/Kconfig"
menu "System Type"
choice
prompt "ARM system type"
default ARCH_RPC
config ARCH_CLPS7500
bool "Cirrus-CL-PS7500FE"
select TIMER_ACORN
select ISA
config ARCH_CLPS711X
bool "CLPS711x/EP721x-based"
config ARCH_CO285
bool "Co-EBSA285"
select FOOTBRIDGE
select FOOTBRIDGE_ADDIN
config ARCH_EBSA110
bool "EBSA-110"
select ISA
help
This is an evaluation board for the StrongARM processor available
from Digital. It has limited hardware on-board, including an onboard
Ethernet interface, two PCMCIA sockets, two serial ports and a
parallel port.
config ARCH_CAMELOT
bool "Epxa10db"
help
This enables support for Altera's Excalibur XA10 development board.
If you would like to build your kernel to run on one of these boards
then you must say 'Y' here. Otherwise say 'N'
config ARCH_FOOTBRIDGE
bool "FootBridge"
select FOOTBRIDGE
config ARCH_INTEGRATOR
bool "Integrator"
select ARM_AMBA
select ICST525
config ARCH_IOP3XX
bool "IOP3xx-based"
select PCI
config ARCH_IXP4XX
bool "IXP4xx-based"
select DMABOUNCE
select PCI
config ARCH_IXP2000
bool "IXP2400/2800-based"
select PCI
config ARCH_L7200
bool "LinkUp-L7200"
select FIQ
help
Say Y here if you intend to run this kernel on a LinkUp Systems
L7200 Software Development Board which uses an ARM720T processor.
Information on this board can be obtained at:
<http://www.linkupsys.com/>
If you have any questions or comments about the Linux kernel port
to this board, send e-mail to <sjhill@cotw.com>.
config ARCH_PXA
bool "PXA2xx-based"
config ARCH_RPC
bool "RiscPC"
select ARCH_ACORN
select FIQ
select TIMER_ACORN
select ARCH_MAY_HAVE_PC_FDC
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
config ARCH_SA1100
bool "SA1100-based"
select ISA
select ARCH_DISCONTIGMEM_ENABLE
config ARCH_S3C2410
bool "Samsung S3C2410"
help
Samsung S3C2410X CPU based systems, such as the Simtec Electronics
BAST (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or
the Samsung SMDK2410 development board (and derviatives).
config ARCH_SHARK
bool "Shark"
select ISA
select ISA_DMA
select PCI
config ARCH_LH7A40X
bool "Sharp LH7A40X"
help
Say Y here for systems based on one of the Sharp LH7A40X
System on a Chip processors. These CPUs include an ARM922T
core with a wide array of integrated devices for
hand-held and low-power applications.
config ARCH_OMAP
bool "TI OMAP"
config ARCH_VERSATILE
bool "Versatile"
select ARM_AMBA
select ICST307
help
This enables support for ARM Ltd Versatile board.
config ARCH_REALVIEW
bool "RealView"
select ARM_AMBA
select ICST307
help
This enables support for ARM Ltd RealView boards.
config ARCH_IMX
bool "IMX"
config ARCH_H720X
bool "Hynix-HMS720x-based"
help
This enables support for systems based on the Hynix HMS720x
config ARCH_AAEC2000
bool "Agilent AAEC-2000 based"
select ARM_AMBA
help
This enables support for systems based on the Agilent AAEC-2000
endchoice
source "arch/arm/mach-clps711x/Kconfig"
source "arch/arm/mach-epxa10db/Kconfig"
source "arch/arm/mach-footbridge/Kconfig"
source "arch/arm/mach-integrator/Kconfig"
source "arch/arm/mach-iop3xx/Kconfig"
source "arch/arm/mach-ixp4xx/Kconfig"
source "arch/arm/mach-ixp2000/Kconfig"
source "arch/arm/mach-pxa/Kconfig"
source "arch/arm/mach-sa1100/Kconfig"
source "arch/arm/plat-omap/Kconfig"
source "arch/arm/mach-omap1/Kconfig"
source "arch/arm/mach-s3c2410/Kconfig"
source "arch/arm/mach-lh7a40x/Kconfig"
source "arch/arm/mach-imx/Kconfig"
source "arch/arm/mach-h720x/Kconfig"
source "arch/arm/mach-versatile/Kconfig"
source "arch/arm/mach-aaec2000/Kconfig"
source "arch/arm/mach-realview/Kconfig"
# Definitions to make life easier
config ARCH_ACORN
bool
source arch/arm/mm/Kconfig
# bool 'Use XScale PMU as timer source' CONFIG_XSCALE_PMU_TIMER
config XSCALE_PMU
bool
depends on CPU_XSCALE && !XSCALE_PMU_TIMER
default y
endmenu
source "arch/arm/common/Kconfig"
config FORCE_MAX_ZONEORDER
int
depends on SA1111
default "9"
menu "Bus support"
config ARM_AMBA
bool
config ISA
bool
help
Find out whether you have ISA slots on your motherboard. ISA is the
name of a bus system, i.e. the way the CPU talks to the other stuff
inside your box. Other bus systems are PCI, EISA, MicroChannel
(MCA) or VESA. ISA is an older system, now being displaced by PCI;
newer boards don't support it. If you have ISA, say Y, otherwise N.
config ISA_DMA
bool
config ISA_DMA_API
bool
default y
config PCI
bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB
help
Find out whether you have a PCI motherboard. PCI is the name of a
bus system, i.e. the way the CPU talks to the other stuff inside
your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
VESA. If you have PCI, say Y, otherwise N.
The PCI-HOWTO, available from
<http://www.tldp.org/docs.html#howto>, contains valuable
information about which PCI hardware does work under Linux and which
doesn't.
# Select the host bridge type
config PCI_HOST_VIA82C505
bool
depends on PCI && ARCH_SHARK
default y
source "drivers/pci/Kconfig"
source "drivers/pcmcia/Kconfig"
endmenu
menu "Kernel Features"
config SMP
bool "Symmetric Multi-Processing (EXPERIMENTAL)"
depends on EXPERIMENTAL && REALVIEW_MPCORE
help
This enables support for systems with more than one CPU. If you have
a system with only one CPU, like most personal computers, say N. If
you have a system with more than one CPU, say Y.
If you say N here, the kernel will run on single and multiprocessor
machines, but will use only one CPU of a multiprocessor machine. If
you say Y here, the kernel will run on many, but not all, single
processor machines. On a single processor machine, the kernel will
run faster if you say N here.
See also the <file:Documentation/smp.txt>,
<file:Documentation/i386/IO-APIC.txt>,
<file:Documentation/nmi_watchdog.txt> and the SMP-HOWTO available at
<http://www.linuxdoc.org/docs.html#howto>.
If you don't know what to do here, say N.
config NR_CPUS
int "Maximum number of CPUs (2-32)"
range 2 32
depends on SMP
default "4"
config HOTPLUG_CPU
bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
depends on SMP && HOTPLUG && EXPERIMENTAL
help
Say Y here to experiment with turning CPUs off and on. CPUs
can be controlled through /sys/devices/system/cpu.
config PREEMPT
bool "Preemptible Kernel (EXPERIMENTAL)"
depends on EXPERIMENTAL
help
This option reduces the latency of the kernel when reacting to
real-time or interactive events by allowing a low priority process to
be preempted even if it is in kernel mode executing a system call.
This allows applications to run more reliably even when the system is
under load.
Say Y here if you are building a kernel for a desktop, embedded
or real-time system. Say N if you are unsure.
config NO_IDLE_HZ
bool "Dynamic tick timer"
help
Select this option if you want to disable continuous timer ticks
and have them programmed to occur as required. This option saves
power as the system can remain in idle state for longer.
By default dynamic tick is disabled during the boot, and can be
manually enabled with:
echo 1 > /sys/devices/system/timer/timer0/dyn_tick
Alternatively, if you want dynamic tick automatically enabled
during boot, pass "dyntick=enable" via the kernel command string.
Please note that dynamic tick may affect the accuracy of
timekeeping on some platforms depending on the implementation.
Currently at least OMAP, PXA2xx and SA11x0 platforms are known
to have accurate timekeeping with dynamic tick.
config ARCH_DISCONTIGMEM_ENABLE
bool
default (ARCH_LH7A40X && !LH7A40X_CONTIGMEM)
help
Say Y to support efficient handling of discontiguous physical memory,
for architectures which are either NUMA (Non-Uniform Memory Access)
or have huge holes in the physical address space for other reasons.
See <file:Documentation/vm/numa> for more.
source "mm/Kconfig"
config LEDS
bool "Timer and CPU usage LEDs"
depends on ARCH_CDB89712 || ARCH_CO285 || ARCH_EBSA110 || \
ARCH_EBSA285 || ARCH_IMX || ARCH_INTEGRATOR || \
ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \
ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \
ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE
help
If you say Y here, the LEDs on your machine will be used
to provide useful information about your current system status.
If you are compiling a kernel for a NetWinder or EBSA-285, you will
be able to select which LEDs are active using the options below. If
you are compiling a kernel for the EBSA-110 or the LART however, the
red LED will simply flash regularly to indicate that the system is
still functional. It is safe to say Y here if you have a CATS
system, but the driver will do nothing.
config LEDS_TIMER
bool "Timer LED" if (!ARCH_CDB89712 && !ARCH_OMAP) || \
MACH_OMAP_H2 || MACH_OMAP_PERSEUS2
depends on LEDS
default y if ARCH_EBSA110
help
If you say Y here, one of the system LEDs (the green one on the
NetWinder, the amber one on the EBSA285, or the red one on the LART)
will flash regularly to indicate that the system is still
operational. This is mainly useful to kernel hackers who are
debugging unstable kernels.
The LART uses the same LED for both Timer LED and CPU usage LED
functions. You may choose to use both, but the Timer LED function
will overrule the CPU usage LED.
config LEDS_CPU
bool "CPU usage LED" if (!ARCH_CDB89712 && !ARCH_EBSA110 && \
!ARCH_OMAP) || MACH_OMAP_H2 || MACH_OMAP_PERSEUS2
depends on LEDS
help
If you say Y here, the red LED will be used to give a good real
time indication of CPU usage, by lighting whenever the idle task
is not currently executing.
The LART uses the same LED for both Timer LED and CPU usage LED
functions. You may choose to use both, but the Timer LED function
will overrule the CPU usage LED.
config ALIGNMENT_TRAP
bool
default y if !ARCH_EBSA110
help
ARM processors can not fetch/store information which is not
naturally aligned on the bus, i.e., a 4 byte fetch must start at an
address divisible by 4. On 32-bit ARM processors, these non-aligned
fetch/store instructions will be emulated in software if you say
here, which has a severe performance impact. This is necessary for
correct operation of some network protocols. With an IP-only
configuration it is safe to say N, otherwise say Y.
endmenu
menu "Boot options"
# Compressed boot loader in ROM. Yes, we really want to ask about
# TEXT and BSS so we preserve their values in the config files.
config ZBOOT_ROM_TEXT
hex "Compressed ROM boot loader base address"
default "0"
help
The physical address at which the ROM-able zImage is to be
placed in the target. Platforms which normally make use of
ROM-able zImage formats normally set this to a suitable
value in their defconfig file.
If ZBOOT_ROM is not enabled, this has no effect.
config ZBOOT_ROM_BSS
hex "Compressed ROM boot loader BSS address"
default "0"
help
The base address of 64KiB of read/write memory in the target
for the ROM-able zImage, which must be available while the
decompressor is running. Platforms which normally make use of
ROM-able zImage formats normally set this to a suitable
value in their defconfig file.
If ZBOOT_ROM is not enabled, this has no effect.
config ZBOOT_ROM
bool "Compressed boot loader in ROM/flash"
depends on ZBOOT_ROM_TEXT != ZBOOT_ROM_BSS
help
Say Y here if you intend to execute your compressed kernel image
(zImage) directly from ROM or flash. If unsure, say N.
config CMDLINE
string "Default kernel command string"
default ""
help
On some architectures (EBSA110 and CATS), there is currently no way
for the boot loader to pass arguments to the kernel. For these
architectures, you should supply some command-line options at build
time by entering them here. As a minimum, you should specify the
memory size and the root device (e.g., mem=64M root=/dev/nfs).
config XIP_KERNEL
bool "Kernel Execute-In-Place from ROM"
depends on !ZBOOT_ROM
help
Execute-In-Place allows the kernel to run from non-volatile storage
directly addressable by the CPU, such as NOR flash. This saves RAM
space since the text section of the kernel is not loaded from flash
to RAM. Read-write sections, such as the data section and stack,
are still copied to RAM. The XIP kernel is not compressed since
it has to run directly from flash, so it will take more space to
store it. The flash address used to link the kernel object files,
and for storing it, is configuration dependent. Therefore, if you
say Y here, you must know the proper physical address where to
store the kernel image depending on your own flash memory usage.
Also note that the make target becomes "make xipImage" rather than
"make zImage" or "make Image". The final kernel binary to put in
ROM memory will be arch/arm/boot/xipImage.
If unsure, say N.
config XIP_PHYS_ADDR
hex "XIP Kernel Physical Location"
depends on XIP_KERNEL
default "0x00080000"
help
This is the physical address in your flash memory the kernel will
be linked for and stored to. This address is dependent on your
own flash usage.
endmenu
if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP1)
menu "CPU Frequency scaling"
source "drivers/cpufreq/Kconfig"
config CPU_FREQ_SA1100
bool
depends on CPU_FREQ && (SA1100_H3100 || SA1100_H3600 || SA1100_H3800 || SA1100_LART || SA1100_PLEB || SA1100_BADGE4 || SA1100_HACKKIT)
default y
config CPU_FREQ_SA1110
bool
depends on CPU_FREQ && (SA1100_ASSABET || SA1100_CERF || SA1100_PT_SYSTEM3)
default y
config CPU_FREQ_INTEGRATOR
tristate "CPUfreq driver for ARM Integrator CPUs"
depends on ARCH_INTEGRATOR && CPU_FREQ
default y
help
This enables the CPUfreq driver for ARM Integrator CPUs.
For details, take a look at <file:Documentation/cpu-freq>.
If in doubt, say Y.
endmenu
endif
menu "Floating point emulation"
comment "At least one emulation must be selected"
config FPE_NWFPE
bool "NWFPE math emulation"
---help---
Say Y to include the NWFPE floating point emulator in the kernel.
This is necessary to run most binaries. Linux does not currently
support floating point hardware so you need to say Y here even if
your machine has an FPA or floating point co-processor podule.
You may say N here if you are going to load the Acorn FPEmulator
early in the bootup.
config FPE_NWFPE_XP
bool "Support extended precision"
depends on FPE_NWFPE
help
Say Y to include 80-bit support in the kernel floating-point
emulator. Otherwise, only 32 and 64-bit support is compiled in.
Note that gcc does not generate 80-bit operations by default,
so in most cases this option only enlarges the size of the
floating point emulator without any good reason.
You almost surely want to say N here.
config FPE_FASTFPE
bool "FastFPE math emulation (EXPERIMENTAL)"
depends on !CPU_32v3 && EXPERIMENTAL
---help---
Say Y here to include the FAST floating point emulator in the kernel.
This is an experimental much faster emulator which now also has full
precision for the mantissa. It does not support any exceptions.
It is very simple, and approximately 3-6 times faster than NWFPE.
It should be sufficient for most programs. It may be not suitable
for scientific calculations, but you have to check this for yourself.
If you do not feel you need a faster FP emulation you should better
choose NWFPE.
config VFP
bool "VFP-format floating point maths"
depends on CPU_V6 || CPU_ARM926T
help
Say Y to include VFP support code in the kernel. This is needed
if your hardware includes a VFP unit.
Please see <file:Documentation/arm/VFP/release-notes.txt> for
release notes and additional status information.
Say N if your target does not have VFP hardware.
endmenu
menu "Userspace binary formats"
source "fs/Kconfig.binfmt"
config ARTHUR
tristate "RISC OS personality"
help
Say Y here to include the kernel code necessary if you want to run
Acorn RISC OS/Arthur binaries under Linux. This code is still very
experimental; if this sounds frightening, say N and sleep in peace.
You can also say M here to compile this support as a module (which
will be called arthur).
endmenu
menu "Power management options"
config PM
bool "Power Management support"
---help---
"Power Management" means that parts of your computer are shut
off or put into a power conserving "sleep" mode if they are not
being used. There are two competing standards for doing this: APM
and ACPI. If you want to use either one, say Y here and then also
to the requisite support below.
Power Management is most important for battery powered laptop
computers; if you have a laptop, check out the Linux Laptop home
page on the WWW at <http://www.linux-on-laptops.com/> or
Tuxmobil - Linux on Mobile Computers at <http://www.tuxmobil.org/>
and the Battery Powered Linux mini-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
config APM
tristate "Advanced Power Management Emulation"
depends on PM
---help---
APM is a BIOS specification for saving power using several different
techniques. This is mostly useful for battery powered laptops with
APM compliant BIOSes. If you say Y here, the system time will be
reset after a RESUME operation, the /proc/apm device will provide
battery status information, and user-space programs will receive
notification of APM "events" (e.g. battery status change).
In order to use APM, you will need supporting software. For location
and more information, read <file:Documentation/pm.txt> and the
Battery Powered Linux mini-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
This driver does not spin down disk drives (see the hdparm(8)
manpage ("man 8 hdparm") for that), and it doesn't turn off
VESA-compliant "green" monitors.
Generally, if you don't have a battery in your machine, there isn't
much point in using this driver and you should say N. If you get
random kernel OOPSes or reboots that don't seem to be related to
anything, try disabling/enabling this option (or disabling/enabling
APM in your BIOS).
endmenu
source "net/Kconfig"
menu "Device Drivers"
source "drivers/base/Kconfig"
if ALIGNMENT_TRAP
source "drivers/mtd/Kconfig"
endif
source "drivers/parport/Kconfig"
source "drivers/pnp/Kconfig"
source "drivers/block/Kconfig"
source "drivers/acorn/block/Kconfig"
if PCMCIA || ARCH_CLPS7500 || ARCH_IOP3XX || ARCH_IXP4XX \
|| ARCH_L7200 || ARCH_LH7A40X || ARCH_PXA || ARCH_RPC \
|| ARCH_S3C2410 || ARCH_SA1100 || ARCH_SHARK || FOOTBRIDGE
source "drivers/ide/Kconfig"
endif
source "drivers/scsi/Kconfig"
source "drivers/md/Kconfig"
source "drivers/message/fusion/Kconfig"
source "drivers/ieee1394/Kconfig"
source "drivers/message/i2o/Kconfig"
source "drivers/net/Kconfig"
source "drivers/isdn/Kconfig"
# input before char - char/joystick depends on it. As does USB.
source "drivers/input/Kconfig"
source "drivers/char/Kconfig"
source "drivers/i2c/Kconfig"
source "drivers/hwmon/Kconfig"
#source "drivers/l3/Kconfig"
source "drivers/misc/Kconfig"
source "drivers/mfd/Kconfig"
source "drivers/media/Kconfig"
source "drivers/video/Kconfig"
source "sound/Kconfig"
source "drivers/usb/Kconfig"
source "drivers/mmc/Kconfig"
endmenu
source "fs/Kconfig"
source "arch/arm/oprofile/Kconfig"
source "arch/arm/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"
