Decoder firmware API description
================================
Note: this API is part of the decoder firmware, so it's cx23415 only.
-------------------------------------------------------------------------------
Name CX2341X_DEC_PING_FW
Enum 0/0x00
Description
This API call does nothing. It may be used to check if the firmware
is responding.
-------------------------------------------------------------------------------
Name CX2341X_DEC_START_PLAYBACK
Enum 1/0x01
Description
Begin or resume playback.
Param[0]
0 based frame number in GOP to begin playback from.
Param[1]
Specifies the number of muted audio frames to play before normal
audio resumes.
-------------------------------------------------------------------------------
Name CX2341X_DEC_STOP_PLAYBACK
Enum 2/0x02
Description
Ends playback and clears all decoder buffers. If PTS is not zero,
playback stops at specified PTS.
Param[0]
Display 0=last frame, 1=black
Param[1]
PTS low
Param[2]
PTS high
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_PLAYBACK_SPEED
Enum 3/0x03
Description
Playback stream at speed other than normal. There are two modes of
operation:
Smooth: host transfers entire stream and firmware drops unused
frames.
Coarse: host drops frames based on indexing as required to achieve
desired speed.
Param[0]
Bitmap:
0:7 0 normal
1 fast only "1.5 times"
n nX fast, 1/nX slow
30 Framedrop:
'0' during 1.5 times play, every other B frame is dropped
'1' during 1.5 times play, stream is unchanged (bitrate
must not exceed 8mbps)
31 Speed:
'0' slow
'1' fast
Param[1]
Direction: 0=forward, 1=reverse
Param[2]
Picture mask:
1=I frames
3=I, P frames
7=I, P, B frames
Param[3]
B frames per GOP (for reverse play only)
Param[4]
Mute audio: 0=disable, 1=enable
Param[5]
Display 0=frame, 1=field
Param[6]
Specifies the number of muted audio frames to play before normal audio
resumes.
-------------------------------------------------------------------------------
Name CX2341X_DEC_STEP_VIDEO
Enum 5/0x05
Description
Each call to this API steps the playback to the next unit defined below
in the current playback direction.
Param[0]
0=frame, 1=top field, 2=bottom field
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_DMA_BLOCK_SIZE
Enum 8/0x08
Description
Set DMA transfer block size. Counterpart to API 0xC9
Param[0]
DMA transfer block size in bytes. A different size may be specified
when issuing the DMA transfer command.
-------------------------------------------------------------------------------
Name CX2341X_DEC_GET_XFER_INFO
Enum 9/0x09
Description
This API call may be used to detect an end of stream condition.
Result[0]
Stream type
Result[1]
Address offset
Result[2]
Maximum bytes to transfer
Result[3]
Buffer fullness
-------------------------------------------------------------------------------
Name CX2341X_DEC_GET_DMA_STATUS
Enum 10/0x0A
Description
Status of the last DMA transfer
Result[0]
Bit 1 set means transfer complete
Bit 2 set means DMA error
Bit 3 set means linked list error
Result[1]
DMA type: 0=MPEG, 1=OSD, 2=YUV
-------------------------------------------------------------------------------
Name CX2341X_DEC_SCHED_DMA_FROM_HOST
Enum 11/0x0B
Description
Setup DMA from host operation. Counterpart to API 0xCC
Param[0]
Memory address of link list
Param[1]
Total # of bytes to transfer
Param[2]
DMA type (0=MPEG, 1=OSD, 2=YUV)
-------------------------------------------------------------------------------
Name CX2341X_DEC_PAUSE_PLAYBACK
Enum 13/0x0D
Description
Freeze playback immediately. In this mode, when internal buffers are
full, no more data will be accepted and data request IRQs will be
masked.
Param[0]
Display: 0=last frame, 1=black
-------------------------------------------------------------------------------
Name CX2341X_DEC_HALT_FW
Enum 14/0x0E
Description
The firmware is halted and no further API calls are serviced until
the firmware is uploaded again.
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_STANDARD
Enum 16/0x10
Description
Selects display standard
Param[0]
0=NTSC, 1=PAL
-------------------------------------------------------------------------------
Name CX2341X_DEC_GET_VERSION
Enum 17/0x11
Description
Returns decoder firmware version information
Result[0]
Version bitmask:
Bits 0:15 build
Bits 16:23 minor
Bits 24:31 major
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_STREAM_INPUT
Enum 20/0x14
Description
Select decoder stream input port
Param[0]
0=memory (default), 1=streaming
-------------------------------------------------------------------------------
Name CX2341X_DEC_GET_TIMING_INFO
Enum 21/0x15
Description
Returns timing information from start of playback
Result[0]
Frame count by decode order
Result[1]
Video PTS bits 0:31 by display order
Result[2]
Video PTS bit 32 by display order
Result[3]
SCR bits 0:31 by display order
Result[4]
SCR bit 32 by display order
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_AUDIO_MODE
Enum 22/0x16
Description
Select audio mode
Param[0]
Dual mono mode action
Param[1]
Stereo mode action:
0=Stereo, 1=Left, 2=Right, 3=Mono, 4=Swap, -1=Unchanged
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_EVENT_NOTIFICATION
Enum 23/0x17
Description
Setup firmware to notify the host about a particular event.
Counterpart to API 0xD5
Param[0]
Event: 0=Audio mode change between stereo and dual channel
Param[1]
Notification 0=disabled, 1=enabled
Param[2]
Interrupt bit
Param[3]
Mailbox slot, -1 if no mailbox required.
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_DISPLAY_BUFFERS
Enum 24/0x18
Description
Number of display buffers. To decode all frames in reverse playback you
must use nine buffers.
Param[0]
0=six buffers, 1=nine buffers
-------------------------------------------------------------------------------
Name CX2341X_DEC_EXTRACT_VBI
Enum 25/0x19
Description
Extracts VBI data
Param[0]
0=extract from extension & user data, 1=extract from private packets
Result[0]
VBI table location
Result[1]
VBI table size
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_DECODER_SOURCE
Enum 26/0x1A
Description
Selects decoder source. Ensure that the parameters passed to this
API match the encoder settings.
Param[0]
Mode: 0=MPEG from host, 1=YUV from encoder, 2=YUV from host
Param[1]
YUV picture width
Param[2]
YUV picture height
Param[3]
Bitmap: see Param[0] of API 0xBD
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_AUDIO_OUTPUT
Enum 27/0x1B
Description
Select audio output format
Param[0]
Bitmask:
0:1 Data size:
'00' 16 bit
'01' 20 bit
'10' 24 bit
2:7 Unused
8:9 Mode:
'00' 2 channels
'01' 4 channels
'10' 6 channels
'11' 6 channels with one line data mode
(for left justified MSB first mode, 20 bit only)
10:11 Unused
12:13 Channel format:
'00' right justified MSB first mode
'01' left justified MSB first mode
'10' I2S mode
14:15 Unused
16:21 Right justify bit count
22:31 Unused
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_AV_DELAY
Enum 28/0x1C
Description
Set audio/video delay in 90Khz ticks
Param[0]
0=A/V in sync, negative=audio lags, positive=video lags
-------------------------------------------------------------------------------
Name CX2341X_DEC_SET_PREBUFFERING
Enum 30/0x1E
Description
Decoder prebuffering, when enabled up to 128KB are buffered for
streams <8mpbs or 640KB for streams >8mbps
Param[0]
0=off, 1=on
