litmus-rt.git/drivers/rapidio, branch linux-tip

rapidio: use resource_size()

2010-11-12T15:55:30+00:00

The size calculation is done incorrectly here because it should include
both the start and end (end - start + 1).  It's easiest to just use
resource_size() which does the right thing.

I was worried there was something non-standard going on because the
printk() subtracts "end - 1", but the rest of the file uses the normal
resource size calculations.  This function is only called from
fsl_rio_setup() in arch/powerpc/sysdev/fsl_rio.c and the calculation
there is also:

	port->iores.start = law_start;
	port->iores.end = law_start + law_size - 1;

So I think this is the correct fix.

Signed-off-by: Dan Carpenter 
Cc: Alexandre Bounine 
Acked-by: Li Yang 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: fix destructive port EM initialization for Tsi568

2010-10-28T01:03:16+00:00

Replace possibly damaging broadcast writes into the per-port SP_MODE
registers with individual writes for each port.  This will preserve
individual port configurations in case if ports are configured
differently.

Signed-off-by: Alexandre Bounine 
Cc: Kumar Gala 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Thomas Moll 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: fix maximum port number in tsi57x EM initialization

2010-10-28T01:03:16+00:00

Replace hardcoded maximum port number with actual reported number of
switch ports.

Signed-off-by: Alexandre Bounine 
Cc: Kumar Gala 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Thomas Moll 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: fix IDLE2 bits corruption

2010-10-28T01:03:16+00:00

RapidIO spec v.2.1 adds Idle Sequence 2 into LP-Serial Physical Layer.
The fix ensures that corresponding bits are not corrupted during error
handling.

Signed-off-by: Alexandre Bounine 
Cc: Thomas Moll 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Kumar Gala 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: add handling of redundant routes

2010-10-28T01:03:16+00:00

Detects RIO link to the already enumerated device and properly sets links
between device objects.  Changes to the enumeration/discovery logic:

1. Use Master Enable bit to signal end of the enumeration - agents may
   start their discovery process as soon as they see this bit set
   (Component Tag register was used before for this purpose).

2. Enumerator sets Component Tag (!= 0) immediately during device
   setup.  This allows to identify the device if the redundant route
   exists in a RIO system.

Signed-off-by: Alexandre Bounine 
Cc: Thomas Moll 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Kumar Gala 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: add support for IDT CPS Gen2 switches

2010-10-28T01:03:16+00:00

Add the RIO switch driver and definitions for IDT CPS-1848 and CPS-1616
Gen2 devices.

Signed-off-by: Alexandre Bounine 
Cc: Thomas Moll 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Kumar Gala 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: add device access check into the enumeration

2010-10-28T01:03:16+00:00

Add explicit device access check before performing device enumeration.
This gives a chance to clear possible link error conditions by issuing
safe maintenance read request(s).

Signed-off-by: Alexandre Bounine 
Cc: Thomas Moll 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Kumar Gala 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: add handling of orphan port-write message

2010-10-28T01:03:15+00:00

Add check for access to port-write (PW) message source device before
processing the PW message.  If source RIO device is not available (power
down or RIO link failure) trace back to a last available switch/port on
the PW message route and service failure at that point.

Signed-off-by: Alexandre Bounine 
Cc: Thomas Moll 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Kumar Gala 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: modify sysfs initialization for switches

2010-10-28T01:03:15+00:00

1. Change to create attribute "routes" only for switches.

2. Add a switch-specific callback to create/remove proprietary attributes.

Signed-off-by: Alexandre Bounine 
Cc: Thomas Moll 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Kumar Gala 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds

rapidio: add default handler for error-stopped state

2010-10-28T01:03:15+00:00

The default error-stopped state handler provides recovery mechanism as
defined by RIO specification.

Signed-off-by: Alexandre Bounine 
Cc: Thomas Moll 
Cc: Matt Porter 
Cc: Li Yang 
Cc: Kumar Gala 
Cc: Micha Nelissen 
Signed-off-by: Andrew Morton 
Signed-off-by: Linus Torvalds