litmus-rt.git/drivers/net/phy/Makefile, branch test

net: Allow FIXED_PHY to be modular.

2014-12-16T20:02:23+00:00

Otherwise we get things like:

warning: (NET_DSA_BCM_SF2 && BCMGENET && SYSTEMPORT) selects FIXED_PHY which has unmet direct dependencies (NETDEVICES && PHYLIB=y)

In order to make this work we have to rename fixed.c to fixed_phy.c
because the regulator drivers already have a module named "fixed.o".

Signed-off-by: David S. Miller

net: phy: add generic UniMAC MDIO bus driver

2014-08-28T05:59:39+00:00

Add a generic UniMAC MDIO bus driver and its Device Tree binding, which
can be used by the BCMGENET driver as-is, and the upcoming Starfighter 2
Ethernet switch MDIO bus controller.

Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

amd-xgbe: Configuration and build support

2014-06-05T22:26:51+00:00

This patch provides the Kconfig and Makefile changes needed
to configure and build the AMD 10GbE platform driver and the
AMD 10GbE phylib driver.

Signed-off-by: Tom Lendacky 
Signed-off-by: David S. Miller

net: phy: add Broadcom BCM7xxx internal PHY driver

2014-02-14T05:27:58+00:00

This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:

- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)

The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.

Signed-off-by: Florian Fainelli 
Signed-off-by: David S. Miller

phy: Add MOXA MDIO driver

2013-11-07T20:37:09+00:00

The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".

This patch adds an MDIO driver which handles the MII bus.

Signed-off-by: Jonas Jensen 
Signed-off-by: David S. Miller

net: Add MDIO bus driver for the Allwinner EMAC

2013-06-01T00:23:07+00:00

This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.

Signed-off-by: Maxime Ripard 
Tested-by: Richard Genoud 
Signed-off-by: David S. Miller

phy: add AT803x driver

2012-10-18T19:34:30+00:00

This driver add support for wake over lan on AT803x phys.

Signed-off-by: Matus Ujhelyi 
Signed-off-by: David S. Miller

netdev/phy: add MDIO bus multiplexer driven by a memory-mapped device

2012-08-30T16:54:48+00:00

Add support for an MDIO bus multiplexer controlled by a simple memory-mapped
device, like an FPGA.  The device must be memory-mapped and contain only
8-bit registers (which keeps things simple).

Tested on a Freescale P5020DS board which uses the "PIXIS" FPGA attached
to the localbus.

Signed-off-by: Timur Tabi 
Signed-off-by: David S. Miller

netdev/phy: Add driver for Broadcom BCM87XX 10G Ethernet PHYs

2012-06-28T04:23:25+00:00

Add a driver for BCM8706 and BCM8727 devices.  These are a 10Gig PHYs
which use MII_ADDR_C45 addressing.  They are always 10G full duplex, so
there is no autonegotiation.  All we do is report link state and send
interrupts when it changes.

If the PHY has a device tree of_node associated with it, the
"broadcom,c45-reg-init" property is used to supply register
initialization values when config_init() is called.

Signed-off-by: David Daney 
Signed-off-by: David S. Miller

netdev/of/phy: Add MDIO bus multiplexer driven by GPIO lines.

2012-05-08T02:58:09+00:00

The GPIO pins select which sub bus is connected to the master.

Initially tested with an sn74cbtlv3253 switch device wired into the
MDIO bus.

Signed-off-by: David Daney 
Signed-off-by: David S. Miller