litmus-rt.git/drivers/net/can/Kconfig, branch linux-tip

pch_can: depends on PCI

2010-10-25T23:47:36+00:00

Fix pch_can build when CONFIG_PCI is not enabled.  It uses pci interfaces
and data structures, so it should depend on PCI.

drivers/net/can/pch_can.c:1044: error: implicit declaration of function 'pci_enable_msi'
drivers/net/can/pch_can.c:1079: error: implicit declaration of function 'pci_disable_msi'

Signed-off-by: Randy Dunlap 
Signed-off-by: David S. Miller

can: Topcliff: Add PCH_CAN driver.

2010-10-24T21:42:57+00:00

CAN driver of Topcliff PCH

Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus.
Topcliff PCH has CAN I/F. This driver enables CAN function.

Signed-off-by: Masayuki Ohtake 
Signed-off-by: David S. Miller

CAN: Add Flexcan CAN controller driver

2010-07-22T16:06:25+00:00

This core is found on some Freescale SoCs and also some Coldfire
SoCs. Support for Coldfire is missing though at the moment as
they have an older revision of the core which does not have RX FIFO
support.

Signed-off-by: Sascha Hauer 
Signed-off-by: Marc Kleine-Budde 
Acked-by: Wolfgang Grandegger 
Signed-off-by: Marc Kleine-Budde

can: Add support for Janz VMOD-ICAN3 Intelligent CAN module

2010-05-27T23:37:33+00:00

The Janz VMOD-ICAN3 is a MODULbus daughterboard which fits onto any
MODULbus carrier board. It is an intelligent CAN controller with a
microcontroller and associated firmware.

Signed-off-by: Ira W. Snyder 
Acked-by: Wolfgang Grandegger 
Acked-by: David S. Miller 
Signed-off-by: Samuel Ortiz

can: CAN_MCP251X should depend on HAS_DMA

2009-12-14T03:56:36+00:00

When building for Sun 3:

drivers/net/can/mcp251x.c:1074: undefined reference to `dma_free_coherent'
drivers/net/can/mcp251x.c:976: undefined reference to `dma_alloc_coherent'
drivers/net/can/mcp251x.c:1050: undefined reference to `dma_free_coherent'

Signed-off-by: Geert Uytterhoeven 
Signed-off-by: David S. Miller

can: add the driver for Analog Devices Blackfin on-chip CAN controllers

2009-12-11T23:07:58+00:00

Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: H.J. Oertel 
Signed-off-by: Wolfgang Grandegger 
Signed-off-by: David S. Miller

net/can/mscan: improve build

2009-11-17T11:57:34+00:00

- move Kconfig entries to the subdirectory
- do remaining renames of mpc52xx to mpc5xxx

Signed-off-by: Wolfram Sang 
Signed-off-by: David S. Miller

Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6

2009-11-17T08:05:02+00:00

Conflicts:
	drivers/net/can/Kconfig

net/can: add driver for mscan family & mpc52xx_mscan

2009-11-14T04:47:03+00:00

Taken from socketcan-svn, fixed remaining todos, cleaned up, tested with a
phyCORE-MPC5200B-IO and a custom board.

Signed-off-by: Wolfram Sang 
Cc: Wolfgang Grandegger 
Cc: Grant Likely 
Cc: David Miller 
Signed-off-by: David S. Miller

can: Fix driver Kconfig structure

2009-11-14T03:56:55+00:00

In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig
entry right behind an entry of the same *vendor*. This teared the SJA1000
based driver selection into pieces.

This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves
the SJA1000 and USB Kconfig portions into the belonging directories.

As there are many new CAN drivers in the queue getting this cleanup into
2.6.32-rc would massively reduce the problems for the upcoming drivers.

Thanks,
Oliver

Signed-off-by: Oliver Hartkopp 
Signed-off-by: Wolfgang Grandegger 
Signed-off-by: David S. Miller