With (some) Technisat cards you cannot run multiple DVB applications
in parallel and switch the channel at the same time.

There seems to be a problem on the interfaces or even inside the flexcop-device
that can't handle interruption on the streaming interface.

This patch adds a watchdog to check whether data is supposed to come in
(streaming PIDs are requested) and if no data is seen within 400ms (default) it
resets the streaming/pid-filtering hardware.

This patch is urgently needed to support the rev 2.8 of the hardware and solves
problem occassionally seen on older hardware.

Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This commit adds support for the CX24113 DVB-S tuner driver and thus support for the Technisat Skystar2 revision 2.8.
The driver was created with the help of Technisat. Thank you very much.

Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
  net: Allow dependancies of FDDI & Tokenring to be modular.
  igb: Fix build warning when DCA is disabled.
  net: Fix warning fallout from recent NAPI interface changes.
  gro: Fix potential use after free
  sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
  sfc: When disabling the NIC, close the device rather than unregistering it
  sfc: SFT9001: Add cable diagnostics
  sfc: Add support for multiple PHY self-tests
  sfc: Merge top-level functions for self-tests
  sfc: Clean up PHY mode management in loopback self-test
  sfc: Fix unreliable link detection in some loopback modes
  sfc: Generate unique names for per-NIC workqueues
  802.3ad: use standard ethhdr instead of ad_header
  802.3ad: generalize out mac address initializer
  802.3ad: initialize ports LACPDU from const initializer
  802.3ad: remove typedef around ad_system
  802.3ad: turn ports is_individual into a bool
  802.3ad: turn ports is_enabled into a bool
  802.3ad: make ntt bool
  ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
  ...

Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).

When the tuner modules were moved to common/tuners, a separate customize
option were added for tuners. However, the automatic selection of the
tuners were still using the older option.

This causes that the automatic selection to fail, if DVB_FE_CUSTOMISE is
selected. Also, since those tuners are now under MEDIA_TUNER_CUSTOMIZE
menu, if you unset MEDIA_TUNER_CUSTOMIZE, you can't manually select the
tuners.

This patch fixes this error by replacing DVB_FE_CUSTOMISE by
MEDIA_TUNER_CUSTOMIZE on all places were a tuner is selected.

The patch were generated by this small script:

for i in `find drivers/media -name Kconfig`; do
  cat $i|perl -ne 's/(MEDIA_TUNER.*)DVB_FE_CUSTOMISE/\1MEDIA_TUNER_CUSTOMIZE/; print $_' >a
  mv a $i
done

Also, manually reordered the tuner entries.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

At some point the Flexcop driver was changed to support newer Flexcop cards.
These modifications however broke the detection of Cablestar 2 DVB-C cards.

The reason is that the earlier version of the driver used to retry
unsuccessful i2c operations. The demodulator of Cablestar 2 cards (stv0297)
seems to be very dependent on these retries and adding them back fixes
Cablestar detection.

This patch restores this behaviour for the CableStar2.

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Different backends have different input busses (saa7146, flexcop).
To reflect that a config-option to the s5h1420-driver was added which makes
the output mode selectable.

Furthermore the s5h1420-driver is now doing the same i2c-method as it was done
before adding support for other i2c-users.

This patch needs to go into the current release of the kernel, as this driver
is currently broken.

(Thanks to Eberhard Kaltenhaeuser for helping out to debug this issue.)

Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

b2c2-flexcop, dvb/bt8xx and video/bt8xx fails to build on ARM with:

__bad_udelay is specifically designed on ARM to fail when udelay is
called in a bad way.  arch/arm/include/asm/delay.h has this to say
about __bad_udelay:

/*
 * This function intentionally does not exist; if you see references to
 * it, it means that you're calling udelay() with an out of range value.
 *
 * With currently imposed limits, this means that we support a max delay
 * of 2000us. Further limits: HZ<=1000 and bogomips<=3355
 */
extern void __bad_udelay(void);

Solution is to replace udelay by a mdelay and udelay with value less than 2000

Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Some DVB drivers are incorrectly assuming that the size of
i2c_adapter.name is I2C_NAME_SIZE.  Here's a fix.

Also change strncpy to strlcpy, as the former is error-prone (and was
indeed incorrectly used.)

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Uwe Bugla <uwe.bugla@gmx.de>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>