litmus-rt.git/drivers/bcma/Makefile, branch test

bcma: prepare Kconfig symbol for PCI driver

2015-03-05T12:11:45+00:00

Driver for PCIe core requires PCI to be enabled, however we shouldn't
require it for the whole bus. Someone may be not interested in extra
PCI devices and what's more there are SoCs without any PCI at all (like
BCM5356C0, BCM5357*, BCM47186B0). For more details see Kconfig "help".
Please note this patch doesn't allow disabling PCI drivers yet, as it
requires more work on calls to bcma_core_pci_* functions.

Signed-off-by: Rafał Miłecki 
Signed-off-by: Kalle Valo

bcma: add support for chipcommon B core

2014-09-09T19:33:05+00:00

This core is used on BCM4708 to configure the PCIe and USB3 PHYs and it
contains the addresses to the Device Management unit. This will be used
by the PCIe driver first.

Signed-off-by: Hauke Mehrtens 
Signed-off-by: John W. Linville

bcma: add driver for PCIe Gen 2 core

2014-07-07T20:32:16+00:00

New Broadcom PCIe devices (802.11ac ones?) use Gen2 and have to be
initialized differently.

Signed-off-by: Rafał Miłecki 
Signed-off-by: John W. Linville

bcma: add GPIO driver

2012-11-21T20:55:52+00:00

Register a GPIO driver to access the GPIOs provided by the chip.
The GPIOs of the SoC should always start at 0 and the other GPIOs could
start at a random position. There is just one SoC in a system and when
they start at 0 the number is predictable.

Signed-off-by: Hauke Mehrtens 
Patchwork: http://patchwork.linux-mips.org/patch/4587
Acked-by: Florian Fainelli

bcma: add place for flash memory support

2012-07-17T19:11:40+00:00

Signed-off-by: Rafał Miłecki 
Signed-off-by: John W. Linville

bcma: add trivial GBIT MAC COMMON driver

2012-07-12T19:27:18+00:00

GMAC COMMON core is present on BCM4706 and is used for example to access
board PHYs (PHYs can not be accessed directly using GBIT MAC core).

Signed-off-by: Rafał Miłecki 
Acked-by: Hauke Mehrtens 
Signed-off-by: John W. Linville

bcma: add mips driver

2011-08-08T18:29:26+00:00

This adds a mips driver to bcma. This is only found on embedded
devices. For now the driver just initializes the irqs used on this
system.

Signed-off-by: Hauke Mehrtens 
Acked-by: Ralf Baechle 
Signed-off-by: John W. Linville

bcma: add SOC bus

2011-08-08T18:29:25+00:00

This patch adds support for using bcma on a Broadcom SoC as the system
bus. An SoC like the bcm4716 could register this bus and use it to
searches for the bcma cores and register the devices on this bus.

BCMA_HOSTTYPE_NONE was intended for SoCs at first but BCMA_HOSTTYPE_SOC
is a better name.

Acked-by: Rafał Miłecki 
Signed-off-by: Hauke Mehrtens 
Acked-by: Ralf Baechle 
Signed-off-by: John W. Linville

bcma: detect PCI core working in hostmode

2011-07-07T17:13:34+00:00

We must not init it like clientmode one, it would break device (tested
by Hauke on BCM4718). Add stub hostmode driver for now.

Signed-off-by: Rafał Miłecki 
Signed-off-by: Hauke Mehrtens 
Signed-off-by: John W. Linville

bcma: read SPROM and extract MAC from it

2011-06-03T19:01:07+00:00

In case of BCMA cards SPROM is located in the ChipCommon core, it is
not mapped as separated host window. So far we have met only SPROMs rev
8.
SPROM layout seems to be the same as for SSB buses, so we decided to
share SPROM struct and some defines.
For now we extract MAC address only, this can be improved of course.

Signed-off-by: Rafał Miłecki 
Signed-off-by: John W. Linville