litmus-rt.git/arch/arm/mach-u300/Makefile, branch master

kbuild: remove unnecessary variable initializaions

2014-10-02T11:55:02+00:00

Clearing obj-y, obj-m, obj-n, obj- in each Makefile is
a useless habit.

They are non-exported variables; therefore they are always empty
whenever descending into each subdirectory.
(Moreorver, obj-y and obj-m are also set to empty at the beginning
of scripts/Makefile.build)

Signed-off-by: Masahiro Yamada 
Acked-by: Nicolas Ferre 
Acked-by: Peter Foley 
Acked-by: Linus Walleij 
Signed-off-by: Michal Marek

ARM: u300: move timer driver to clocksource

2014-03-11T22:04:43+00:00

Move the U300 timer driver down to the clocksource driver
subsystem and keep arch/arm clean.

Cc: Daniel Lezcano 
Cc: Thomas Gleixner 
Signed-off-by: Linus Walleij 
Signed-off-by: Daniel Lezcano

ARM: u300: delete all static board data

2013-06-17T11:54:30+00:00

We have now transferred all the U300 peripherals to the device
tree, so we just select USE_OF, and delete all static board data,
then require that this platform shall be booted using the device
tree and nothing else.

This gets rid of the MMCI (PL180), PL022, and serial PL011
platform data entries and more.

Signed-off-by: Linus Walleij

ARM: u300: merge u300.c into core.c and rid headers

2012-08-13T11:53:06+00:00

This gets rid of the separate u300.c file in mach-u300 since
it can just as well live right in core.c, then we also get
rid of the broadcasted  file that is not
helping anyone. Put the interface to the system timer into
a separate header.

Signed-off-by: Linus Walleij

ARM: u300: convert to common clock

2012-07-11T22:36:45+00:00

This converts the U300 clock implementation over to use the common
struct clk and moves the implementation down into drivers/clk.
Since VCO isn't used in tree it was removed, it's not hard to
put it back in if need be.

Signed-off-by: Linus Walleij 
[mturquette@linaro.org: trivial Makefile conflict]
Signed-off-by: Mike Turquette

ARM: 7335/1: mach-u300: do away with MMC config files

2012-02-23T22:22:45+00:00

All the special stuff (like registering input device and so on)
for the U300 MMC is now done away with. We don't need these
special MMC setup kludges, merge this into core.c and be done
with it.

Signed-off-by: Linus Walleij 
Signed-off-by: Russell King

pinctrl: add a driver for the U300 pinmux

2011-10-13T10:57:45+00:00

This adds a driver for the U300 pinmux portions of the system
controller "SYSCON". It also serves as an example of how to use
the pinmux subsystem. This driver also houses the platform data
for the only supported platform.

This deletes the old U300 driver in arch/arm/mach-u300 and
replace it with a driver using the new subsystem.

The new driver is considerably fatter than the old one, but it
also registers all 467 pins of the system and adds the power
and EMIF pin groups and corresponding functions. The idea
is to use this driver as a a reference for other
implementation so it needs to be as complete and verbose
as possible.

Reviewed-by: Barry Song <21cnbao@gmail.com>
[Fixup for changed function names and semantics in the v10 patch]
Signed-off-by: Linus Walleij

gpio: move U300 GPIO driver to drivers/gpio

2011-05-26T23:29:33+00:00

This moves the U300 GPIO driver out of arch/arm/mach-u300 and into
the desired location indicated by the subsystem maintainer.

Signed-off-by: Linus Walleij 
Signed-off-by: Grant Likely

ARM: 5724/1: U300 AB3100 boardinfo v5

2009-10-19T16:10:09+00:00

This defines regulator platform data and board power
regulator hogs for the ST-Ericsson U300 platform.

Cc: Mark Brown 
Cc: Liam Girdwood 
Cc: Samuel Ortiz 
Signed-off-by: Linus Walleij 
Signed-off-by: Russell King

ARM: 5668/2: U300 I2C board setup

2009-08-15T14:36:29+00:00

This sets up the U300 I2C subdevices so that the AB3100
analog baseband ASIC is properly detected and also the
camera devices in the U335 reference design get properly
registered.

Signed-off-by: Linus Walleij 
Signed-off-by: Russell King