From afa842fa641e11a025725883b04d1e144e6bad39 Mon Sep 17 00:00:00 2001 From: "Stephen M. Cameron" Date: Fri, 22 Oct 2010 14:21:07 -0500 Subject: cciss: fix board status waiting code After a reset, we should first wait for the board to become "not ready", and then wait for it to become "ready", instead of immediately waiting for it to become "ready", and do this waiting *after* restoring PCI config space registers. Signed-off-by: Stephen M. Cameron Signed-off-by: Jens Axboe --- drivers/block/cciss.c | 43 +++++++++++++++++++++++++++++++++++-------- 1 file changed, 35 insertions(+), 8 deletions(-) (limited to 'drivers/block/cciss.c') diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c index f09e6df15aa..fd08644bf2a 100644 --- a/drivers/block/cciss.c +++ b/drivers/block/cciss.c @@ -4006,18 +4006,31 @@ static int __devinit cciss_pci_find_memory_BAR(struct pci_dev *pdev, return -ENODEV; } -static int __devinit cciss_wait_for_board_ready(ctlr_info_t *h) +static int __devinit cciss_wait_for_board_state(struct pci_dev *pdev, + void __iomem *vaddr, int wait_for_ready) +#define BOARD_READY 1 +#define BOARD_NOT_READY 0 { - int i; + int i, iterations; u32 scratchpad; - for (i = 0; i < CCISS_BOARD_READY_ITERATIONS; i++) { - scratchpad = readl(h->vaddr + SA5_SCRATCHPAD_OFFSET); - if (scratchpad == CCISS_FIRMWARE_READY) - return 0; + if (wait_for_ready) + iterations = CCISS_BOARD_READY_ITERATIONS; + else + iterations = CCISS_BOARD_NOT_READY_ITERATIONS; + + for (i = 0; i < iterations; i++) { + scratchpad = readl(vaddr + SA5_SCRATCHPAD_OFFSET); + if (wait_for_ready) { + if (scratchpad == CCISS_FIRMWARE_READY) + return 0; + } else { + if (scratchpad != CCISS_FIRMWARE_READY) + return 0; + } msleep(CCISS_BOARD_READY_POLL_INTERVAL_MSECS); } - dev_warn(&h->pdev->dev, "board not ready, timed out.\n"); + dev_warn(&pdev->dev, "board not ready, timed out.\n"); return -ENODEV; } @@ -4183,7 +4196,7 @@ static int __devinit cciss_pci_init(ctlr_info_t *h) err = -ENOMEM; goto err_out_free_res; } - err = cciss_wait_for_board_ready(h); + err = cciss_wait_for_board_state(h->pdev, h->vaddr, BOARD_READY); if (err) goto err_out_free_res; err = cciss_find_cfgtables(h); @@ -4534,6 +4547,20 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) need a little pause here */ msleep(CCISS_POST_RESET_PAUSE_MSECS); + /* Wait for board to become not ready, then ready. */ + dev_info(&pdev->dev, "Waiting for board to become ready.\n"); + rc = cciss_wait_for_board_state(pdev, vaddr, BOARD_NOT_READY); + if (rc) /* Don't bail, might be E500, etc. which can't be reset */ + dev_warn(&pdev->dev, + "failed waiting for board to become not ready\n"); + rc = cciss_wait_for_board_state(pdev, vaddr, BOARD_READY); + if (rc) { + dev_warn(&pdev->dev, + "failed waiting for board to become ready\n"); + goto unmap_cfgtable; + } + dev_info(&pdev->dev, "board ready.\n"); + /* Controller should be in simple mode at this point. If it's not, * It means we're on one of those controllers which doesn't support * the doorbell reset method and on which the PCI power management reset -- cgit v1.2.2 From f442e64b93e16dba6bf9ab7e8dc5a90f6bcd8a85 Mon Sep 17 00:00:00 2001 From: "Stephen M. Cameron" Date: Fri, 22 Oct 2010 14:21:12 -0500 Subject: cciss: Use kernel provided PCI state save and restore functions and use the doorbell reset method if available (which doesn't lock up the controller if you properly save and restore all the PCI registers that you're supposed to.) Signed-off-by: Stephen M. Cameron Signed-off-by: Jens Axboe --- drivers/block/cciss.c | 73 +++++++++++---------------------------------------- 1 file changed, 15 insertions(+), 58 deletions(-) (limited to 'drivers/block/cciss.c') diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c index fd08644bf2a..2e547bddc5a 100644 --- a/drivers/block/cciss.c +++ b/drivers/block/cciss.c @@ -4361,36 +4361,6 @@ static __devinit int cciss_message(struct pci_dev *pdev, unsigned char opcode, u #define cciss_soft_reset_controller(p) cciss_message(p, 1, 0) #define cciss_noop(p) cciss_message(p, 3, 0) -static __devinit int cciss_reset_msi(struct pci_dev *pdev) -{ -/* the #defines are stolen from drivers/pci/msi.h. */ -#define msi_control_reg(base) (base + PCI_MSI_FLAGS) -#define PCI_MSIX_FLAGS_ENABLE (1 << 15) - - int pos; - u16 control = 0; - - pos = pci_find_capability(pdev, PCI_CAP_ID_MSI); - if (pos) { - pci_read_config_word(pdev, msi_control_reg(pos), &control); - if (control & PCI_MSI_FLAGS_ENABLE) { - dev_info(&pdev->dev, "resetting MSI\n"); - pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSI_FLAGS_ENABLE); - } - } - - pos = pci_find_capability(pdev, PCI_CAP_ID_MSIX); - if (pos) { - pci_read_config_word(pdev, msi_control_reg(pos), &control); - if (control & PCI_MSIX_FLAGS_ENABLE) { - dev_info(&pdev->dev, "resetting MSI-X\n"); - pci_write_config_word(pdev, msi_control_reg(pos), control & ~PCI_MSIX_FLAGS_ENABLE); - } - } - - return 0; -} - static int cciss_controller_hard_reset(struct pci_dev *pdev, void * __iomem vaddr, bool use_doorbell) { @@ -4445,17 +4415,17 @@ static int cciss_controller_hard_reset(struct pci_dev *pdev, * states or using the doorbell register. */ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) { - u16 saved_config_space[32]; u64 cfg_offset; u32 cfg_base_addr; u64 cfg_base_addr_index; void __iomem *vaddr; unsigned long paddr; u32 misc_fw_support, active_transport; - int rc, i; + int rc; CfgTable_struct __iomem *cfgtable; bool use_doorbell; u32 board_id; + u16 command_register; /* For controllers as old a the p600, this is very nearly * the same thing as @@ -4465,14 +4435,6 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) * pci_set_power_state(pci_dev, PCI_D0); * pci_restore_state(pci_dev); * - * but we can't use these nice canned kernel routines on - * kexec, because they also check the MSI/MSI-X state in PCI - * configuration space and do the wrong thing when it is - * set/cleared. Also, the pci_save/restore_state functions - * violate the ordering requirements for restoring the - * configuration space from the CCISS document (see the - * comment below). So we roll our own .... - * * For controllers newer than the P600, the pci power state * method of resetting doesn't work so we have another way * using the doorbell register. @@ -4491,8 +4453,13 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) return -ENODEV; } - for (i = 0; i < 32; i++) - pci_read_config_word(pdev, 2*i, &saved_config_space[i]); + /* Save the PCI command register */ + pci_read_config_word(pdev, 4, &command_register); + /* Turn the board off. This is so that later pci_restore_state() + * won't turn the board on before the rest of config space is ready. + */ + pci_disable_device(pdev); + pci_save_state(pdev); /* find the first memory BAR, so we can find the cfg table */ rc = cciss_pci_find_memory_BAR(pdev, &paddr); @@ -4527,21 +4494,13 @@ static __devinit int cciss_kdump_hard_reset_controller(struct pci_dev *pdev) rc = cciss_controller_hard_reset(pdev, vaddr, use_doorbell); if (rc) goto unmap_cfgtable; - - /* Restore the PCI configuration space. The Open CISS - * Specification says, "Restore the PCI Configuration - * Registers, offsets 00h through 60h. It is important to - * restore the command register, 16-bits at offset 04h, - * last. Do not restore the configuration status register, - * 16-bits at offset 06h." Note that the offset is 2*i. - */ - for (i = 0; i < 32; i++) { - if (i == 2 || i == 3) - continue; - pci_write_config_word(pdev, 2*i, saved_config_space[i]); + pci_restore_state(pdev); + rc = pci_enable_device(pdev); + if (rc) { + dev_warn(&pdev->dev, "failed to enable device.\n"); + goto unmap_cfgtable; } - wmb(); - pci_write_config_word(pdev, 4, saved_config_space[2]); + pci_write_config_word(pdev, 4, command_register); /* Some devices (notably the HP Smart Array 5i Controller) need a little pause here */ @@ -4601,8 +4560,6 @@ static __devinit int cciss_init_reset_devices(struct pci_dev *pdev) return 0; /* just try to do the kdump anyhow. */ if (rc) return -ENODEV; - if (cciss_reset_msi(pdev)) - return -ENODEV; /* Now try to get the controller to respond to a no-op */ for (i = 0; i < CCISS_POST_RESET_NOOP_RETRIES; i++) { -- cgit v1.2.2 From 186fb9cf6a1154bc9b071adfd72fcf256285eb26 Mon Sep 17 00:00:00 2001 From: "Stephen M. Cameron" Date: Fri, 22 Oct 2010 14:21:17 -0500 Subject: cciss: limit commands allocated on reset_devices This is to conserve memory in a memory-limited kdump scenario Signed-off-by: Stephen M. Cameron Signed-off-by: Jens Axboe --- drivers/block/cciss.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers/block/cciss.c') diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c index 2e547bddc5a..9e761b994b4 100644 --- a/drivers/block/cciss.c +++ b/drivers/block/cciss.c @@ -4079,6 +4079,11 @@ static int __devinit cciss_find_cfgtables(ctlr_info_t *h) static void __devinit cciss_get_max_perf_mode_cmds(struct ctlr_info *h) { h->max_commands = readl(&(h->cfgtable->MaxPerformantModeCommands)); + + /* Limit commands in memory limited kdump scenario. */ + if (reset_devices && h->max_commands > 32) + h->max_commands = 32; + if (h->max_commands < 16) { dev_warn(&h->pdev->dev, "Controller reports " "max supported commands of %d, an obvious lie. " -- cgit v1.2.2 From 332c2f80a894d349bfb95fae00daf74477d4afcd Mon Sep 17 00:00:00 2001 From: "Stephen M. Cameron" Date: Fri, 22 Oct 2010 14:21:22 -0500 Subject: cciss: use usleep_range not msleep for small sleeps Signed-off-by: Stephen M. Cameron Signed-off-by: Jens Axboe --- drivers/block/cciss.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/block/cciss.c') diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c index 9e761b994b4..c792a6080d5 100644 --- a/drivers/block/cciss.c +++ b/drivers/block/cciss.c @@ -3785,7 +3785,7 @@ static void __devinit cciss_wait_for_mode_change_ack(ctlr_info_t *h) for (i = 0; i < MAX_CONFIG_WAIT; i++) { if (!(readl(h->vaddr + SA5_DOORBELL) & CFGTBL_ChangeReq)) break; - msleep(10); + usleep_range(10000, 20000); } } -- cgit v1.2.2 From 4205df34003eec4371020872cdfa228ffae5bd6a Mon Sep 17 00:00:00 2001 From: "Stephen M. Cameron" Date: Sat, 23 Oct 2010 18:47:31 +0200 Subject: cciss: remove controllers supported by hpsa We would prefer not to have any overlap between the two drivers. Remove the cciss_allow_hpsa option, as it it is no longer needed. Signed-off-by: Stephen M. Cameron Signed-off-by: Jens Axboe --- drivers/block/cciss.c | 45 ++++----------------------------------------- 1 file changed, 4 insertions(+), 41 deletions(-) (limited to 'drivers/block/cciss.c') diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c index c792a6080d5..39631cbccaf 100644 --- a/drivers/block/cciss.c +++ b/drivers/block/cciss.c @@ -66,11 +66,6 @@ MODULE_VERSION("3.6.26"); MODULE_LICENSE("GPL"); static DEFINE_MUTEX(cciss_mutex); -static int cciss_allow_hpsa; -module_param(cciss_allow_hpsa, int, S_IRUGO|S_IWUSR); -MODULE_PARM_DESC(cciss_allow_hpsa, - "Prevent cciss driver from accessing hardware known to be " - " supported by the hpsa driver"); #include "cciss_cmd.h" #include "cciss.h" @@ -98,19 +93,6 @@ static const struct pci_device_id cciss_pci_device_id[] = { {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSD, 0x103C, 0x3215}, {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSC, 0x103C, 0x3237}, {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSC, 0x103C, 0x323D}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSE, 0x103C, 0x3241}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSE, 0x103C, 0x3243}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSE, 0x103C, 0x3245}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSE, 0x103C, 0x3247}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSE, 0x103C, 0x3249}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSE, 0x103C, 0x324A}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSE, 0x103C, 0x324B}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3350}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3351}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3352}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3353}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3354}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3355}, {0,} }; @@ -131,6 +113,8 @@ static struct board_type products[] = { {0x409D0E11, "Smart Array 6400 EM", &SA5_access}, {0x40910E11, "Smart Array 6i", &SA5_access}, {0x3225103C, "Smart Array P600", &SA5_access}, + {0x3223103C, "Smart Array P800", &SA5_access}, + {0x3234103C, "Smart Array P400", &SA5_access}, {0x3235103C, "Smart Array P400i", &SA5_access}, {0x3211103C, "Smart Array E200i", &SA5_access}, {0x3212103C, "Smart Array E200", &SA5_access}, @@ -138,24 +122,7 @@ static struct board_type products[] = { {0x3214103C, "Smart Array E200i", &SA5_access}, {0x3215103C, "Smart Array E200i", &SA5_access}, {0x3237103C, "Smart Array E500", &SA5_access}, -/* controllers below this line are also supported by the hpsa driver. */ -#define HPSA_BOUNDARY 0x3223103C - {0x3223103C, "Smart Array P800", &SA5_access}, - {0x3234103C, "Smart Array P400", &SA5_access}, - {0x323D103C, "Smart Array P700m", &SA5_access}, - {0x3241103C, "Smart Array P212", &SA5_access}, - {0x3243103C, "Smart Array P410", &SA5_access}, - {0x3245103C, "Smart Array P410i", &SA5_access}, - {0x3247103C, "Smart Array P411", &SA5_access}, - {0x3249103C, "Smart Array P812", &SA5_access}, - {0x324A103C, "Smart Array P712m", &SA5_access}, - {0x324B103C, "Smart Array P711m", &SA5_access}, - {0x3350103C, "Smart Array", &SA5_access}, - {0x3351103C, "Smart Array", &SA5_access}, - {0x3352103C, "Smart Array", &SA5_access}, - {0x3353103C, "Smart Array", &SA5_access}, - {0x3354103C, "Smart Array", &SA5_access}, - {0x3355103C, "Smart Array", &SA5_access}, + {0x323d103c, "Smart Array P700M", &SA5_access}, }; /* How long to wait (in milliseconds) for board to go into simple mode */ @@ -3969,13 +3936,9 @@ static int __devinit cciss_lookup_board_id(struct pci_dev *pdev, u32 *board_id) *board_id = ((subsystem_device_id << 16) & 0xffff0000) | subsystem_vendor_id; - for (i = 0; i < ARRAY_SIZE(products); i++) { - /* Stand aside for hpsa driver on request */ - if (cciss_allow_hpsa && products[i].board_id == HPSA_BOUNDARY) - return -ENODEV; + for (i = 0; i < ARRAY_SIZE(products); i++) if (*board_id == products[i].board_id) return i; - } dev_warn(&pdev->dev, "unrecognized board ID: 0x%08x, ignoring.\n", *board_id); return -ENODEV; -- cgit v1.2.2