From 28fd2d397bab5c7fb0eed0c20b6766c99ae34a8f Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 12 Dec 2008 00:24:33 +0000 Subject: [ARM] S3C64XX: Set GPIO pin when select IRQ_EINT type Set the GPIO pin mode to external interrupt when configuring an IRQ_EINT's IRQ type. Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/irq-eint.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/irq-eint.c b/arch/arm/plat-s3c64xx/irq-eint.c index 1f7cc0067f5..5d62f2799ea 100644 --- a/arch/arm/plat-s3c64xx/irq-eint.c +++ b/arch/arm/plat-s3c64xx/irq-eint.c @@ -14,12 +14,15 @@ #include #include +#include #include #include #include #include +#include +#include #include #include @@ -74,6 +77,7 @@ static void s3c_irq_eint_maskack(unsigned int irq) static int s3c_irq_eint_set_type(unsigned int irq, unsigned int type) { int offs = eint_offset(irq); + int pin; int shift; u32 ctrl, mask; u32 newvalue = 0; @@ -125,6 +129,15 @@ static int s3c_irq_eint_set_type(unsigned int irq, unsigned int type) ctrl |= newvalue << shift; __raw_writel(ctrl, reg); + /* set the GPIO pin appropriately */ + + if (offs < 23) + pin = S3C64XX_GPN(offs); + else + pin = S3C64XX_GPM(offs - 23); + + s3c_gpio_cfgpin(pin, S3C_GPIO_SFN(2)); + return 0; } -- cgit v1.2.2 From 789b4ad36c7037758309df98f1efa65d0c26527d Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Mon, 26 Jan 2009 19:12:01 +0000 Subject: [ARM] S3C64XX: Fix section mismatch for s3c64xx_register_clocks() Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/clock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/clock.c b/arch/arm/plat-s3c64xx/clock.c index 136c982c68e..ad1b9682c9c 100644 --- a/arch/arm/plat-s3c64xx/clock.c +++ b/arch/arm/plat-s3c64xx/clock.c @@ -248,7 +248,7 @@ static struct clk *clks[] __initdata = { &clk_48m, }; -void s3c64xx_register_clocks(void) +void __init s3c64xx_register_clocks(void) { struct clk *clkp; int ret; -- cgit v1.2.2 From 778974797793e7dcd42e3701e09c686b6419cb35 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 23 Jan 2009 16:29:41 +0000 Subject: [ARM] SMDK6410: Correct I2C device name for WM8580 The WM8580 driver registers itself as "wm8580" rather than "WM8580". Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/mach-s3c6410/mach-smdk6410.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c6410/mach-smdk6410.c b/arch/arm/mach-s3c6410/mach-smdk6410.c index 3c4d47145c8..0436783c87d 100644 --- a/arch/arm/mach-s3c6410/mach-smdk6410.c +++ b/arch/arm/mach-s3c6410/mach-smdk6410.c @@ -146,7 +146,7 @@ static struct platform_device *smdk6410_devices[] __initdata = { static struct i2c_board_info i2c_devs0[] __initdata = { { I2C_BOARD_INFO("24c08", 0x50), }, - { I2C_BOARD_INFO("WM8580", 0X1b), }, + { I2C_BOARD_INFO("wm8580", 0x1b), }, }; static struct i2c_board_info i2c_devs1[] __initdata = { -- cgit v1.2.2 From 027191a8c6602d3fb6dde3820517339e1daf191d Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 23 Jan 2009 16:29:43 +0000 Subject: [ARM] SMDK6410: Declare iodesc table static Shuts up a warning. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/mach-s3c6410/mach-smdk6410.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-s3c6410/mach-smdk6410.c b/arch/arm/mach-s3c6410/mach-smdk6410.c index 0436783c87d..25f7935576f 100644 --- a/arch/arm/mach-s3c6410/mach-smdk6410.c +++ b/arch/arm/mach-s3c6410/mach-smdk6410.c @@ -129,7 +129,7 @@ static struct s3c_fb_platdata smdk6410_lcd_pdata __initdata = { .vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC, }; -struct map_desc smdk6410_iodesc[] = {}; +static struct map_desc smdk6410_iodesc[] = {}; static struct platform_device *smdk6410_devices[] __initdata = { #ifdef CONFIG_SMDK6410_SD_CH0 -- cgit v1.2.2 From 8bd8dbdf3725ce569467bd704840249869f626d6 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 23 Jan 2009 16:29:44 +0000 Subject: [ARM] S3C64XX: Staticise s3c64xx_init_irq_eint() It's an initcall and does not need to be exported. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/irq-eint.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/irq-eint.c b/arch/arm/plat-s3c64xx/irq-eint.c index 5d62f2799ea..8d1b7290aa1 100644 --- a/arch/arm/plat-s3c64xx/irq-eint.c +++ b/arch/arm/plat-s3c64xx/irq-eint.c @@ -194,7 +194,7 @@ static void s3c_irq_demux_eint20_27(unsigned int irq, struct irq_desc *desc) s3c_irq_demux_eint(20, 27); } -int __init s3c64xx_init_irq_eint(void) +static int __init s3c64xx_init_irq_eint(void) { int irq; -- cgit v1.2.2 From 24d4076734b4ecf083a6be611040fe0743e59989 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Fri, 23 Jan 2009 17:06:23 +0000 Subject: [ARM] S3C64XX: Do gpiolib configuration earlier arch_initcall() runs after the machine init function which means that any configuration of GPIO pins must currently be done later on, for example in callbacks from drivers. Move the initialisation earlier in order to allow machines to configure GPIOs directly in their init functions rather than having to have a callback invoked later on. Some other ARM platforms use this method. Other solutions for this include providing a special interface for setting up GPIOs en masse, adding callbacks to do the GPIO configuration from devices and doing the GPIO configuration implicitly. Signed-off-by: Mark Brown Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/gpiolib.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/gpiolib.c b/arch/arm/plat-s3c64xx/gpiolib.c index cc62941d7b5..ee9188add8f 100644 --- a/arch/arm/plat-s3c64xx/gpiolib.c +++ b/arch/arm/plat-s3c64xx/gpiolib.c @@ -417,4 +417,4 @@ static __init int s3c64xx_gpiolib_init(void) return 0; } -arch_initcall(s3c64xx_gpiolib_init); +core_initcall(s3c64xx_gpiolib_init); -- cgit v1.2.2 From 4271c3bd46a0f0448118cf618c7210237a98e6bf Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 26 Feb 2009 23:00:27 +0000 Subject: [ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH The USB OHCI host device expects the IRQ definition to be named IRQ_USBH, so rename the S3C64XX IRQ header to match. Signed-off-by: Ben Dooks Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/include/plat/irqs.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/include/plat/irqs.h b/arch/arm/plat-s3c64xx/include/plat/irqs.h index 2846f550b72..f865bf4d709 100644 --- a/arch/arm/plat-s3c64xx/include/plat/irqs.h +++ b/arch/arm/plat-s3c64xx/include/plat/irqs.h @@ -117,7 +117,7 @@ #define IRQ_ONENAND1 S3C64XX_IRQ_VIC1(12) #define IRQ_NFC S3C64XX_IRQ_VIC1(13) #define IRQ_CFCON S3C64XX_IRQ_VIC1(14) -#define IRQ_UHOST S3C64XX_IRQ_VIC1(15) +#define IRQ_USBH S3C64XX_IRQ_VIC1(15) #define IRQ_SPI0 S3C64XX_IRQ_VIC1(16) #define IRQ_SPI1 S3C64XX_IRQ_VIC1(17) #define IRQ_IIC S3C64XX_IRQ_VIC1(18) -- cgit v1.2.2 From 19c5957081a6ffbf014e6c944e6aafee3c1632c3 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 26 Feb 2009 23:00:33 +0000 Subject: [ARM] S3C64XX: Fix name of USB host clock. The usb-host-bus clock should be named usb-bus-host. Signed-off-by: Ben Dooks Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/s3c6400-clock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index 8d9a0cada66..a2f526bcb38 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -351,7 +351,7 @@ static struct clksrc_clk clk_mmc2 = { static struct clksrc_clk clk_usbhost = { .clk = { - .name = "usb-host-bus", + .name = "usb-bus-host", .id = -1, .ctrlbit = S3C_CLKCON_SCLK_UHOST, .enable = s3c64xx_sclk_ctrl, -- cgit v1.2.2 From 41ba41d7c7e1d2a3c9cdfe16c1ee9f7af4693ae2 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Thu, 26 Feb 2009 23:00:34 +0000 Subject: [ARM] S3C64XX: Fix USB host clock mux list The clock list for the USB host bus clock was in the wrong order, move clk_48m to position 0. Signed-off-by: Ben Dooks Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/s3c6400-clock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index a2f526bcb38..2984270b40a 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -189,10 +189,10 @@ static struct clk_sources clkset_uart = { }; static struct clk *clkset_uhost_list[] = { + &clk_48m, &clk_mout_epll.clk, &clk_dout_mpll, &clk_fin_epll, - &clk_48m, }; static struct clk_sources clkset_uhost = { -- cgit v1.2.2 From 3782d3605522b836f53c6d11f76abf5404425c1b Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 27 Feb 2009 11:25:37 +0000 Subject: [ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c Fix the following sparse warnings in s3c6400-clock.c: 39:12: warning: symbol 'clk_ext_xtal_mux' was not declared. Should it be static? 66:12: warning: symbol 'clk_fout_apll' was not declared. Should it be static? 81:19: warning: symbol 'clk_mout_apll' was not declared. Should it be static? 91:12: warning: symbol 'clk_fout_epll' was not declared. Should it be static? 106:19: warning: symbol 'clk_mout_epll' was not declared. Should it be static? 126:19: warning: symbol 'clk_mout_mpll' was not declared. Should it be static? 148:12: warning: symbol 'clk_dout_mpll' was not declared. Should it be static? Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/s3c6400-clock.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index 2984270b40a..6edbeef6aa9 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -36,7 +36,7 @@ * ext_xtal_mux for want of an actual name from the manual. */ -struct clk clk_ext_xtal_mux = { +static struct clk clk_ext_xtal_mux = { .name = "ext_xtal", .id = -1, }; @@ -63,7 +63,7 @@ struct clksrc_clk { void __iomem *reg_divider; }; -struct clk clk_fout_apll = { +static struct clk clk_fout_apll = { .name = "fout_apll", .id = -1, }; @@ -78,7 +78,7 @@ static struct clk_sources clk_src_apll = { .nr_sources = ARRAY_SIZE(clk_src_apll_list), }; -struct clksrc_clk clk_mout_apll = { +static struct clksrc_clk clk_mout_apll = { .clk = { .name = "mout_apll", .id = -1, @@ -88,7 +88,7 @@ struct clksrc_clk clk_mout_apll = { .sources = &clk_src_apll, }; -struct clk clk_fout_epll = { +static struct clk clk_fout_epll = { .name = "fout_epll", .id = -1, }; @@ -103,7 +103,7 @@ static struct clk_sources clk_src_epll = { .nr_sources = ARRAY_SIZE(clk_src_epll_list), }; -struct clksrc_clk clk_mout_epll = { +static struct clksrc_clk clk_mout_epll = { .clk = { .name = "mout_epll", .id = -1, @@ -123,7 +123,7 @@ static struct clk_sources clk_src_mpll = { .nr_sources = ARRAY_SIZE(clk_src_mpll_list), }; -struct clksrc_clk clk_mout_mpll = { +static struct clksrc_clk clk_mout_mpll = { .clk = { .name = "mout_mpll", .id = -1, @@ -145,7 +145,7 @@ static unsigned long s3c64xx_clk_doutmpll_get_rate(struct clk *clk) return rate; } -struct clk clk_dout_mpll = { +static struct clk clk_dout_mpll = { .name = "dout_mpll", .id = -1, .parent = &clk_mout_mpll.clk, -- cgit v1.2.2 From fdca9bf2dae14218704ddd7dc60ad1b198c1d787 Mon Sep 17 00:00:00 2001 From: Ben Dooks Date: Fri, 27 Feb 2009 11:29:23 +0000 Subject: [ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c Fix the following sparse warnings in arch/arm/plat-s3c64xx/irq.c arch/arm/plat-s3c64xx/irq.c:210:23: warning: incorrect type in initializer (different address spaces) arch/arm/plat-s3c64xx/irq.c:210:23: expected void *reg_base arch/arm/plat-s3c64xx/irq.c:210:23: got void [noderef] *regs arch/arm/plat-s3c64xx/irq.c:215:2: warning: incorrect type in argument 1 (different address spaces) arch/arm/plat-s3c64xx/irq.c:215:2: expected void const volatile [noderef] * arch/arm/plat-s3c64xx/irq.c:215:2: got void * Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/irq.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/irq.c b/arch/arm/plat-s3c64xx/irq.c index a94f1d5e819..f22edf7c2d2 100644 --- a/arch/arm/plat-s3c64xx/irq.c +++ b/arch/arm/plat-s3c64xx/irq.c @@ -207,7 +207,7 @@ static struct irq_chip s3c_irq_uart = { static void __init s3c64xx_uart_irq(struct uart_irq *uirq) { - void *reg_base = uirq->regs; + void __iomem *reg_base = uirq->regs; unsigned int irq; int offs; -- cgit v1.2.2 From efeff568677aa325f84d3ce37c219019887a79eb Mon Sep 17 00:00:00 2001 From: Werner Almesberger Date: Fri, 27 Feb 2009 08:03:07 -0300 Subject: [ARM] S3C64XX: Fix s3c64xx_setrate_clksrc Some of the rate selection logic in s3c64xx_setrate_clksrc uses what appears to be parent clock selection logic. This patch corrects it. I also added a check for overly large dividers to prevent them from changing unrelated clocks. Signed-off-by: Werner Almesberger Signed-off-by: Ben Dooks --- arch/arm/plat-s3c64xx/s3c6400-clock.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/plat-s3c64xx/s3c6400-clock.c b/arch/arm/plat-s3c64xx/s3c6400-clock.c index 6edbeef6aa9..05b17528041 100644 --- a/arch/arm/plat-s3c64xx/s3c6400-clock.c +++ b/arch/arm/plat-s3c64xx/s3c6400-clock.c @@ -239,10 +239,12 @@ static int s3c64xx_setrate_clksrc(struct clk *clk, unsigned long rate) rate = clk_round_rate(clk, rate); div = clk_get_rate(clk->parent) / rate; + if (div > 16) + return -EINVAL; val = __raw_readl(reg); - val &= ~sclk->mask; - val |= (rate - 1) << sclk->shift; + val &= ~(0xf << sclk->shift); + val |= (div - 1) << sclk->shift; __raw_writel(val, reg); return 0; -- cgit v1.2.2 From 6b8036a877fe7a85d4474ddb89993339303959e1 Mon Sep 17 00:00:00 2001 From: Grant Likely Date: Sat, 28 Feb 2009 21:30:38 -0700 Subject: powerpc/4xx: Enable SERIAL_OF support by default for Virtex platforms Virtex FPGA designs have two serial port logic cores to choose from; the simple uartlite, and the full featured uart16550. Both cores are in common use so the defconfig should support both of them. Currently only console on uartlite is supported in the defconfig. This patch adds console support for the 16550 core. The Virtex reference designs do not work without this patch. Signed-off-by: Grant Likely --- arch/powerpc/configs/40x/virtex_defconfig | 2 +- arch/powerpc/configs/44x/virtex5_defconfig | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/configs/40x/virtex_defconfig b/arch/powerpc/configs/40x/virtex_defconfig index b6888384dd7..f5698f962e5 100644 --- a/arch/powerpc/configs/40x/virtex_defconfig +++ b/arch/powerpc/configs/40x/virtex_defconfig @@ -686,7 +686,7 @@ CONFIG_SERIAL_UARTLITE_CONSOLE=y CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y # CONFIG_SERIAL_JSM is not set -# CONFIG_SERIAL_OF_PLATFORM is not set +CONFIG_SERIAL_OF_PLATFORM=y # CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL is not set CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set diff --git a/arch/powerpc/configs/44x/virtex5_defconfig b/arch/powerpc/configs/44x/virtex5_defconfig index 15aab1ca638..1bf0a63614b 100644 --- a/arch/powerpc/configs/44x/virtex5_defconfig +++ b/arch/powerpc/configs/44x/virtex5_defconfig @@ -691,7 +691,7 @@ CONFIG_SERIAL_UARTLITE_CONSOLE=y CONFIG_SERIAL_CORE=y CONFIG_SERIAL_CORE_CONSOLE=y # CONFIG_SERIAL_JSM is not set -# CONFIG_SERIAL_OF_PLATFORM is not set +CONFIG_SERIAL_OF_PLATFORM=y # CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL is not set CONFIG_UNIX98_PTYS=y # CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set -- cgit v1.2.2 From f45964ed6971db2e7ae6cb9b164def1d23b46612 Mon Sep 17 00:00:00 2001 From: Saeed Bishara Date: Mon, 2 Mar 2009 17:30:36 +0200 Subject: [ARM] orion5x: pass dram mbus data to xor driver This data should be passed to the xor driver in order to initialize the address decoding windows of the xor unit. without this patch, the self tests of the xor will fail unless the address decoding windows were initialized by the boot loader. Signed-off-by: Saeed Bishara Signed-off-by: Nicolas Pitre --- arch/arm/mach-orion5x/common.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c index 0a623379789..8a0e49d8425 100644 --- a/arch/arm/mach-orion5x/common.c +++ b/arch/arm/mach-orion5x/common.c @@ -431,6 +431,10 @@ void __init orion5x_uart1_init(void) /***************************************************************************** * XOR engine ****************************************************************************/ +struct mv_xor_platform_shared_data orion5x_xor_shared_data = { + .dram = &orion5x_mbus_dram_info, +}; + static struct resource orion5x_xor_shared_resources[] = { { .name = "xor low", @@ -448,6 +452,9 @@ static struct resource orion5x_xor_shared_resources[] = { static struct platform_device orion5x_xor_shared = { .name = MV_XOR_SHARED_NAME, .id = 0, + .dev = { + .platform_data = &orion5x_xor_shared_data, + }, .num_resources = ARRAY_SIZE(orion5x_xor_shared_resources), .resource = orion5x_xor_shared_resources, }; -- cgit v1.2.2 From 87d99d6f7ee3ec73b2b0212427b173502ec9d6cb Mon Sep 17 00:00:00 2001 From: David Brownell Date: Wed, 4 Mar 2009 10:07:40 -0800 Subject: ARM: OMAP: Fix compile error if pm.h is included Change the error to a warning. Signed-off-by: David Brownell Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/include/mach/pm.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/plat-omap/include/mach/pm.h b/arch/arm/plat-omap/include/mach/pm.h index 2a9c27ad4c3..37e2f0f38b4 100644 --- a/arch/arm/plat-omap/include/mach/pm.h +++ b/arch/arm/plat-omap/include/mach/pm.h @@ -108,7 +108,7 @@ !defined(CONFIG_ARCH_OMAP15XX) && \ !defined(CONFIG_ARCH_OMAP16XX) && \ !defined(CONFIG_ARCH_OMAP24XX) -#error "Power management for this processor not implemented yet" +#warning "Power management for this processor not implemented yet" #endif #ifndef __ASSEMBLER__ -- cgit v1.2.2 From 80ea3bac3a47bc73efa334d0dd57099d0ff14216 Mon Sep 17 00:00:00 2001 From: Aaro Koskinen Date: Wed, 4 Mar 2009 10:07:41 -0800 Subject: ARM: OMAP: sched_clock() corrected After my OMAP3 board has been running for a while, I'm seeing weird latency traces like this: sh-1574 0d.h2 153us : do_timer (tick_do_update_jiffies64) sh-1574 0d.h2 153us : update_wall_time (do_timer) sh-1574 0d.h2 153us!: omap_32k_read (update_wall_time) sh-1574 0d.h2 1883us : update_xtime_cache (update_wall_time) sh-1574 0d.h2 1883us : clocksource_get_next (update_wall_time) sh-1574 0d.h2 1883us+: _spin_lock_irqsave (clocksource_get_next) and after a while: sh-17818 0d.h3 153us : do_timer (tick_do_update_jiffies64) sh-17818 0d.h3 153us : update_wall_time (do_timer) sh-17818 0d.h3 153us!: omap_32k_read (update_wall_time) sh-17818 0d.h3 1915us : update_xtime_cache (update_wall_time) sh-17818 0d.h3 1915us+: clocksource_get_next (update_wall_time) sh-17818 0d.h3 1945us : _spin_lock_irqsave (clocksource_get_next) Turns out that sched_clock() is using cyc2ns(), which returns NTP adjusted time. The sched_clock() frequency should not be adjusted. The patch deletes omap_32k_ticks_to_nsecs() and rewrites sched_clock() to do the conversion using the constant multiplier. Signed-off-by: Aaro Koskinen Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/common.c | 14 +++++--------- 1 file changed, 5 insertions(+), 9 deletions(-) (limited to 'arch') diff --git a/arch/arm/plat-omap/common.c b/arch/arm/plat-omap/common.c index 0843b8882f9..6825fbb5a05 100644 --- a/arch/arm/plat-omap/common.c +++ b/arch/arm/plat-omap/common.c @@ -199,21 +199,17 @@ static struct clocksource clocksource_32k = { .flags = CLOCK_SOURCE_IS_CONTINUOUS, }; -/* - * Rounds down to nearest nsec. - */ -unsigned long long omap_32k_ticks_to_nsecs(unsigned long ticks_32k) -{ - return cyc2ns(&clocksource_32k, ticks_32k); -} - /* * Returns current time from boot in nsecs. It's OK for this to wrap * around for now, as it's just a relative time stamp. */ unsigned long long sched_clock(void) { - return omap_32k_ticks_to_nsecs(omap_32k_read()); + unsigned long long ret; + + ret = (unsigned long long)omap_32k_read(); + ret = (ret * clocksource_32k.mult_orig) >> clocksource_32k.shift; + return ret; } static int __init omap_init_clocksource_32k(void) -- cgit v1.2.2 From e951651657610305c9af0045fd64c6a5b0bc4b80 Mon Sep 17 00:00:00 2001 From: Aaro Koskinen Date: Wed, 4 Mar 2009 10:07:41 -0800 Subject: ARM: OMAP: Allow I2C bus driver to be compiled as a module Fixes a linker error when OMAP I2C bus driver is compiled as a module: ERROR: "i2c_register_board_info" [arch/arm/plat-omap/i2c.ko] undefined! The I2C utility functions used for board initialization should be always built-in. Signed-off-by: Aaro Koskinen Acked-by: Jarkko Nikula Signed-off-by: Tony Lindgren --- arch/arm/plat-omap/Makefile | 3 ++- arch/arm/plat-omap/include/mach/common.h | 2 +- 2 files changed, 3 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile index deaff58878a..04a100cfb8e 100644 --- a/arch/arm/plat-omap/Makefile +++ b/arch/arm/plat-omap/Makefile @@ -18,7 +18,8 @@ obj-$(CONFIG_CPU_FREQ) += cpu-omap.o obj-$(CONFIG_OMAP_DM_TIMER) += dmtimer.o obj-$(CONFIG_OMAP_DEBUG_DEVICES) += debug-devices.o obj-$(CONFIG_OMAP_DEBUG_LEDS) += debug-leds.o -obj-$(CONFIG_I2C_OMAP) += i2c.o +i2c-omap-$(CONFIG_I2C_OMAP) := i2c.o +obj-y += $(i2c-omap-m) $(i2c-omap-y) # OMAP mailbox framework obj-$(CONFIG_OMAP_MBOX_FWK) += mailbox.o diff --git a/arch/arm/plat-omap/include/mach/common.h b/arch/arm/plat-omap/include/mach/common.h index ef70e2b0f05..e746ec7e785 100644 --- a/arch/arm/plat-omap/include/mach/common.h +++ b/arch/arm/plat-omap/include/mach/common.h @@ -35,7 +35,7 @@ extern void omap_map_common_io(void); extern struct sys_timer omap_timer; extern void omap_serial_init(void); extern void omap_serial_enable_clocks(int enable); -#ifdef CONFIG_I2C_OMAP +#if defined(CONFIG_I2C_OMAP) || defined(CONFIG_I2C_OMAP_MODULE) extern int omap_register_i2c_bus(int bus_id, u32 clkrate, struct i2c_board_info const *info, unsigned len); -- cgit v1.2.2 From 8ca7fe267f58462825729443f3e3b44ef4901cf0 Mon Sep 17 00:00:00 2001 From: Koen Kooi Date: Wed, 4 Mar 2009 10:07:42 -0800 Subject: ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz Changing it do 100kHz is needed to make more devices works properly. Controlling the TI DLP Pico projector[1] doesn't work properly at 400kHz, 100kHz and lower work fine. EDID readout is unaffected by this change. [1] http://focus.ti.com/dlpdmd/docs/dlpdiscovery.tsp?sectionId=60&tabId=2234 Signed-off-by: Koen Kooi Acked-by: David Brownell Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-omap3beagle.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 38c88fbe658..e39cd2c46cf 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -178,7 +178,9 @@ static int __init omap3_beagle_i2c_init(void) #ifdef CONFIG_I2C2_OMAP_BEAGLE omap_register_i2c_bus(2, 400, NULL, 0); #endif - omap_register_i2c_bus(3, 400, NULL, 0); + /* Bus 3 is attached to the DVI port where devices like the pico DLP + * projector don't work reliably with 400kHz */ + omap_register_i2c_bus(3, 100, NULL, 0); return 0; } -- cgit v1.2.2 From d0cac39e4ec8097e4c7099d291b1fdcc0fe56b58 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Wed, 4 Mar 2009 14:43:47 -0800 Subject: sparc64: Fix lost interrupts on sun4u. Based upon a report by Meelis Roos. Sparc64 SBUS and PCI controllers use a combination of IMAP and ICLR registers to manage device interrupts. The IMAP register contains the "valid" enable bit as well as CPU targetting information. Whereas the ICLR register is written with zero at the end of handling an interrupt to reset the state machine for that interrupt to IDLE so it can be sent again. For PCI slot and SBUS slot devices we can have multiple interrupts sharing the same IMAP register. There are individual ICLR registers but only one IMAP register for managing those. We represent each shared case with individual virtual IRQs so the generic IRQ layer thinks there is only one user of the IRQ instance. In such shared IMAP cases this is wrong, so if there are multiple active users then a free_irq() call will prematurely turn off the interrupt by clearing the Valid bit in the IMAP register even though there are other active users. Fix this by simply doing nothing in sun4u_disable_irq() and checking IRQF_DISABLED during IRQ dispatch. This situation doesn't exist in the hypervisor sun4v cases, so I left those alone. Tested-by: Meelis Roos Signed-off-by: David S. Miller --- arch/sparc/kernel/irq_64.c | 29 +++++++++++++++++++---------- 1 file changed, 19 insertions(+), 10 deletions(-) (limited to 'arch') diff --git a/arch/sparc/kernel/irq_64.c b/arch/sparc/kernel/irq_64.c index e289376198e..1c378d8e90c 100644 --- a/arch/sparc/kernel/irq_64.c +++ b/arch/sparc/kernel/irq_64.c @@ -323,17 +323,25 @@ static void sun4u_set_affinity(unsigned int virt_irq, sun4u_irq_enable(virt_irq); } +/* Don't do anything. The desc->status check for IRQ_DISABLED in + * handler_irq() will skip the handler call and that will leave the + * interrupt in the sent state. The next ->enable() call will hit the + * ICLR register to reset the state machine. + * + * This scheme is necessary, instead of clearing the Valid bit in the + * IMAP register, to handle the case of IMAP registers being shared by + * multiple INOs (and thus ICLR registers). Since we use a different + * virtual IRQ for each shared IMAP instance, the generic code thinks + * there is only one user so it prematurely calls ->disable() on + * free_irq(). + * + * We have to provide an explicit ->disable() method instead of using + * NULL to get the default. The reason is that if the generic code + * sees that, it also hooks up a default ->shutdown method which + * invokes ->mask() which we do not want. See irq_chip_set_defaults(). + */ static void sun4u_irq_disable(unsigned int virt_irq) { - struct irq_handler_data *data = get_irq_chip_data(virt_irq); - - if (likely(data)) { - unsigned long imap = data->imap; - unsigned long tmp = upa_readq(imap); - - tmp &= ~IMAP_VALID; - upa_writeq(tmp, imap); - } } static void sun4u_irq_eoi(unsigned int virt_irq) @@ -746,7 +754,8 @@ void handler_irq(int irq, struct pt_regs *regs) desc = irq_desc + virt_irq; - desc->handle_irq(virt_irq, desc); + if (!(desc->status & IRQ_DISABLED)) + desc->handle_irq(virt_irq, desc); bucket_pa = next_pa; } -- cgit v1.2.2 From d4cc510c61b050ef38e842a12feef71c56d7cf81 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Wed, 4 Mar 2009 11:48:46 +0100 Subject: [ARM] 5418/1: restore lr before leaving mcount MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit gcc seems to expect that lr isn't clobbered by mcount, because for a function starting with: static int func(void) { void *ra = __builtin_return_address(0); printk(KERN_EMERG "__builtin_return_address(0) = %pS\n", ra) ... the following assembler is generated by gcc 4.3.2: 0: e1a0c00d mov ip, sp 4: e92dd810 push {r4, fp, ip, lr, pc} 8: e24cb004 sub fp, ip, #4 ; 0x4 c: ebfffffe bl 0 10: e59f0034 ldr r0, [pc, #52] 14: e1a0100e mov r1, lr 18: ebfffffe bl 0 Without this patch obviously __builtin_return_address(0) yields func+0x10 instead of the return address of the caller. Note this patch fixes a similar issue for the routines used with dynamic ftrace even though this isn't currently selectable for ARM. Cc: Abhishek Sagar Cc: Steven Rostedt Cc: Ingo Molnar Signed-off-by: Uwe Kleine-König Signed-off-by: Russell King --- arch/arm/kernel/entry-common.S | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S index 49a6ba926c2..159d0416f27 100644 --- a/arch/arm/kernel/entry-common.S +++ b/arch/arm/kernel/entry-common.S @@ -111,6 +111,7 @@ ENTRY(mcount) .globl mcount_call mcount_call: bl ftrace_stub + ldr lr, [fp, #-4] @ restore lr ldmia sp!, {r0-r3, pc} ENTRY(ftrace_caller) @@ -122,6 +123,7 @@ ENTRY(ftrace_caller) .globl ftrace_call ftrace_call: bl ftrace_stub + ldr lr, [fp, #-4] @ restore lr ldmia sp!, {r0-r3, pc} #else @@ -133,6 +135,7 @@ ENTRY(mcount) adr r0, ftrace_stub cmp r0, r2 bne trace + ldr lr, [fp, #-4] @ restore lr ldmia sp!, {r0-r3, pc} trace: @@ -141,6 +144,7 @@ trace: sub r0, r0, #MCOUNT_INSN_SIZE mov lr, pc mov pc, r2 + mov lr, r1 @ restore lr ldmia sp!, {r0-r3, pc} #endif /* CONFIG_DYNAMIC_FTRACE */ -- cgit v1.2.2 From ef449e6d21b6e560c7ec36ed285ec3a34e0b12ed Mon Sep 17 00:00:00 2001 From: Hartley Sweeten Date: Thu, 5 Mar 2009 17:33:50 +0100 Subject: [ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info Fix build warnings due to struct i2c_board_info in Patch "5311/1: add core support for built in i2c bus" is causing 11 of 39 the build warnings with Kautobuild for ep93xx_defconfig on kernel 2.6.29-rc5-git4. This patch fixes it. Signed-off-by: H Hartley Sweeten Signed-off-by: Russell King --- arch/arm/mach-ep93xx/include/mach/platform.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-ep93xx/include/mach/platform.h b/arch/arm/mach-ep93xx/include/mach/platform.h index 88f7e88f152..05f0f4f2f3c 100644 --- a/arch/arm/mach-ep93xx/include/mach/platform.h +++ b/arch/arm/mach-ep93xx/include/mach/platform.h @@ -4,6 +4,8 @@ #ifndef __ASSEMBLY__ +struct i2c_board_info; + struct ep93xx_eth_data { unsigned char dev_addr[6]; -- cgit v1.2.2 From 20214fcd74bddc16d65d466212f5dd32aafe8868 Mon Sep 17 00:00:00 2001 From: Darius Augulis Date: Mon, 12 Jan 2009 16:22:57 +0200 Subject: MX1 fix include Includes missed irqs.h in devices.c and mx1ads.c. Signed-off-by: Darius Augulis Signed-off-by: Sascha Hauer --- arch/arm/mach-mx1/devices.c | 2 ++ arch/arm/mach-mx1/mx1ads.c | 1 + 2 files changed, 3 insertions(+) (limited to 'arch') diff --git a/arch/arm/mach-mx1/devices.c b/arch/arm/mach-mx1/devices.c index 686d8d2dbb2..a95644193f3 100644 --- a/arch/arm/mach-mx1/devices.c +++ b/arch/arm/mach-mx1/devices.c @@ -23,6 +23,8 @@ #include #include #include + +#include #include static struct resource imx_csi_resources[] = { diff --git a/arch/arm/mach-mx1/mx1ads.c b/arch/arm/mach-mx1/mx1ads.c index 2e4b185fe4a..3200cf60e38 100644 --- a/arch/arm/mach-mx1/mx1ads.c +++ b/arch/arm/mach-mx1/mx1ads.c @@ -21,6 +21,7 @@ #include #include +#include #include #include #include -- cgit v1.2.2 From d0fc63f7bd07cb779a06dc1cdd0c5a14e7f5d562 Mon Sep 17 00:00:00 2001 From: Stuart Bennett Date: Sun, 8 Mar 2009 20:21:35 +0200 Subject: x86 mmiotrace: fix remove_kmmio_fault_pages() Impact: fix race+crash in mmiotrace The list manipulation in remove_kmmio_fault_pages() was broken. If more than one consecutive kmmio_fault_page was re-added during the grace period between unregister_kmmio_probe() and remove_kmmio_fault_pages(), the list manipulation failed to remove pages from the release list. After a second grace period the pages get into rcu_free_kmmio_fault_pages() and raise a BUG_ON() kernel crash. The list manipulation is fixed to properly remove pages from the release list. This bug has been present from the very beginning of mmiotrace in the mainline kernel. It was introduced in 0fd0e3da ("x86: mmiotrace full patch, preview 1"); An urgent fix for Linus. Tested by Stuart (on 32-bit) and Pekka (on amd and intel 64-bit systems, nouveau and nvidia proprietary). Signed-off-by: Stuart Bennett Signed-off-by: Pekka Paalanen LKML-Reference: <20090308202135.34933feb@daedalus.pq.iki.fi> Signed-off-by: Ingo Molnar --- arch/x86/mm/kmmio.c | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/x86/mm/kmmio.c b/arch/x86/mm/kmmio.c index 9f205030d9a..6a518dd08a3 100644 --- a/arch/x86/mm/kmmio.c +++ b/arch/x86/mm/kmmio.c @@ -451,23 +451,24 @@ static void rcu_free_kmmio_fault_pages(struct rcu_head *head) static void remove_kmmio_fault_pages(struct rcu_head *head) { - struct kmmio_delayed_release *dr = container_of( - head, - struct kmmio_delayed_release, - rcu); + struct kmmio_delayed_release *dr = + container_of(head, struct kmmio_delayed_release, rcu); struct kmmio_fault_page *p = dr->release_list; struct kmmio_fault_page **prevp = &dr->release_list; unsigned long flags; + spin_lock_irqsave(&kmmio_lock, flags); while (p) { - if (!p->count) + if (!p->count) { list_del_rcu(&p->list); - else + prevp = &p->release_next; + } else { *prevp = p->release_next; - prevp = &p->release_next; + } p = p->release_next; } spin_unlock_irqrestore(&kmmio_lock, flags); + /* This is the real RCU destroy call. */ call_rcu(&dr->rcu, rcu_free_kmmio_fault_pages); } -- cgit v1.2.2 From ed75d8635abde0c43d26152014e386706475120e Mon Sep 17 00:00:00 2001 From: Guennadi Liakhovetski Date: Thu, 5 Mar 2009 13:25:06 +0000 Subject: powerpc: fix linkstation and storcenter compilation breakage Defining flash partition table in platform code is deprecated, and due to recent changes linkstation and storcenter do not compile any more with their default configurations because of undefined references to physmap_set_partitions(). Instead of fixing them by using the correct kernel configuration macro in preprocessor conditional, remove partition table definitions altogether. Instead add support for partition definition on the command-line and in device tree to the default configurations. Signed-off-by: Guennadi Liakhovetski Signed-off-by: Kumar Gala --- arch/powerpc/configs/linkstation_defconfig | 36 +++++++++++++--------- arch/powerpc/configs/storcenter_defconfig | 35 ++++++++++++++-------- arch/powerpc/platforms/embedded6xx/linkstation.c | 38 ------------------------ arch/powerpc/platforms/embedded6xx/storcenter.c | 32 -------------------- 4 files changed, 44 insertions(+), 97 deletions(-) (limited to 'arch') diff --git a/arch/powerpc/configs/linkstation_defconfig b/arch/powerpc/configs/linkstation_defconfig index aa5855a156d..15900dcf0bf 100644 --- a/arch/powerpc/configs/linkstation_defconfig +++ b/arch/powerpc/configs/linkstation_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.29-rc2 -# Mon Jan 26 15:35:29 2009 +# Linux kernel version: 2.6.29-rc6 +# Fri Mar 6 00:07:38 2009 # # CONFIG_PPC64 is not set @@ -71,6 +71,15 @@ CONFIG_POSIX_MQUEUE=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_CLASSIC_RCU=y +# CONFIG_TREE_RCU is not set +# CONFIG_PREEMPT_RCU is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_PREEMPT_RCU_TRACE is not set CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 @@ -88,6 +97,7 @@ CONFIG_NAMESPACES=y # CONFIG_IPC_NS is not set # CONFIG_USER_NS is not set # CONFIG_PID_NS is not set +# CONFIG_NET_NS is not set CONFIG_BLK_DEV_INITRD=y CONFIG_INITRAMFS_SOURCE="" CONFIG_CC_OPTIMIZE_FOR_SIZE=y @@ -153,11 +163,6 @@ CONFIG_DEFAULT_AS=y # CONFIG_DEFAULT_CFQ is not set # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="anticipatory" -CONFIG_CLASSIC_RCU=y -# CONFIG_TREE_RCU is not set -# CONFIG_PREEMPT_RCU is not set -# CONFIG_TREE_RCU_TRACE is not set -# CONFIG_PREEMPT_RCU_TRACE is not set # CONFIG_FREEZER is not set # @@ -294,7 +299,6 @@ CONFIG_NET=y # # Networking options # -# CONFIG_NET_NS is not set CONFIG_COMPAT_NET_DEV_OPS=y CONFIG_PACKET=y CONFIG_PACKET_MMAP=y @@ -508,8 +512,8 @@ CONFIG_MTD_CONCAT=y CONFIG_MTD_PARTITIONS=y # CONFIG_MTD_TESTS is not set # CONFIG_MTD_REDBOOT_PARTS is not set -# CONFIG_MTD_CMDLINE_PARTS is not set -# CONFIG_MTD_OF_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_OF_PARTS=y # CONFIG_MTD_AR7_PARTS is not set # @@ -587,7 +591,6 @@ CONFIG_MTD_PHYSMAP=y # LPDDR flash memory drivers # # CONFIG_MTD_LPDDR is not set -# CONFIG_MTD_QINFO_PROBE is not set # # UBI - Unsorted block images @@ -617,13 +620,19 @@ CONFIG_BLK_DEV_RAM_SIZE=8192 # CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_PHANTOM is not set -# CONFIG_EEPROM_93CX6 is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set # CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_HP_ILO is not set # CONFIG_C2PORT is not set + +# +# EEPROM support +# +# CONFIG_EEPROM_AT24 is not set +CONFIG_EEPROM_LEGACY=m +# CONFIG_EEPROM_93CX6 is not set CONFIG_HAVE_IDE=y # CONFIG_IDE is not set @@ -839,6 +848,7 @@ CONFIG_R8169=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set +# CONFIG_ATL1C is not set # CONFIG_JME is not set CONFIG_NETDEV_10000=y # CONFIG_CHELSIO_T1 is not set @@ -1037,8 +1047,6 @@ CONFIG_I2C_MPC=y # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set -# CONFIG_EEPROM_AT24 is not set -CONFIG_EEPROM_LEGACY=m # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set diff --git a/arch/powerpc/configs/storcenter_defconfig b/arch/powerpc/configs/storcenter_defconfig index 86512c8790d..94903465ea1 100644 --- a/arch/powerpc/configs/storcenter_defconfig +++ b/arch/powerpc/configs/storcenter_defconfig @@ -1,7 +1,7 @@ # # Automatically generated make config: don't edit -# Linux kernel version: 2.6.29-rc2 -# Mon Jan 26 15:35:46 2009 +# Linux kernel version: 2.6.29-rc6 +# Fri Mar 6 00:09:08 2009 # # CONFIG_PPC64 is not set @@ -71,6 +71,15 @@ CONFIG_SYSVIPC_SYSCTL=y # CONFIG_BSD_PROCESS_ACCT is not set # CONFIG_TASKSTATS is not set # CONFIG_AUDIT is not set + +# +# RCU Subsystem +# +CONFIG_CLASSIC_RCU=y +# CONFIG_TREE_RCU is not set +# CONFIG_PREEMPT_RCU is not set +# CONFIG_TREE_RCU_TRACE is not set +# CONFIG_PREEMPT_RCU_TRACE is not set # CONFIG_IKCONFIG is not set CONFIG_LOG_BUF_SHIFT=14 CONFIG_GROUP_SCHED=y @@ -144,11 +153,6 @@ CONFIG_IOSCHED_CFQ=y CONFIG_DEFAULT_CFQ=y # CONFIG_DEFAULT_NOOP is not set CONFIG_DEFAULT_IOSCHED="cfq" -CONFIG_CLASSIC_RCU=y -# CONFIG_TREE_RCU is not set -# CONFIG_PREEMPT_RCU is not set -# CONFIG_TREE_RCU_TRACE is not set -# CONFIG_PREEMPT_RCU_TRACE is not set # CONFIG_FREEZER is not set # @@ -377,8 +381,8 @@ CONFIG_MTD=y CONFIG_MTD_PARTITIONS=y # CONFIG_MTD_TESTS is not set # CONFIG_MTD_REDBOOT_PARTS is not set -# CONFIG_MTD_CMDLINE_PARTS is not set -# CONFIG_MTD_OF_PARTS is not set +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_OF_PARTS=y # CONFIG_MTD_AR7_PARTS is not set # @@ -452,7 +456,6 @@ CONFIG_MTD_PHYSMAP=y # LPDDR flash memory drivers # # CONFIG_MTD_LPDDR is not set -# CONFIG_MTD_QINFO_PROBE is not set # # UBI - Unsorted block images @@ -478,13 +481,19 @@ CONFIG_BLK_DEV=y # CONFIG_BLK_DEV_HD is not set CONFIG_MISC_DEVICES=y # CONFIG_PHANTOM is not set -# CONFIG_EEPROM_93CX6 is not set # CONFIG_SGI_IOC4 is not set # CONFIG_TIFM_CORE is not set # CONFIG_ICS932S401 is not set # CONFIG_ENCLOSURE_SERVICES is not set # CONFIG_HP_ILO is not set # CONFIG_C2PORT is not set + +# +# EEPROM support +# +# CONFIG_EEPROM_AT24 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_EEPROM_93CX6 is not set CONFIG_HAVE_IDE=y CONFIG_IDE=y @@ -677,6 +686,7 @@ CONFIG_R8169=y # CONFIG_QLA3XXX is not set # CONFIG_ATL1 is not set # CONFIG_ATL1E is not set +# CONFIG_ATL1C is not set # CONFIG_JME is not set # CONFIG_NETDEV_10000 is not set # CONFIG_TR is not set @@ -818,8 +828,6 @@ CONFIG_I2C_MPC=y # Miscellaneous I2C Chip support # # CONFIG_DS1682 is not set -# CONFIG_EEPROM_AT24 is not set -# CONFIG_EEPROM_LEGACY is not set # CONFIG_SENSORS_PCF8574 is not set # CONFIG_PCF8575 is not set # CONFIG_SENSORS_PCA9539 is not set @@ -1159,6 +1167,7 @@ CONFIG_JFFS2_RTIME=y # CONFIG_SYSV_FS is not set # CONFIG_UFS_FS is not set # CONFIG_NETWORK_FILESYSTEMS is not set +CONFIG_EXPORTFS=m # # Partition Types diff --git a/arch/powerpc/platforms/embedded6xx/linkstation.c b/arch/powerpc/platforms/embedded6xx/linkstation.c index 2ca7be65c2d..244f997de79 100644 --- a/arch/powerpc/platforms/embedded6xx/linkstation.c +++ b/arch/powerpc/platforms/embedded6xx/linkstation.c @@ -12,7 +12,6 @@ #include #include -#include #include #include @@ -22,39 +21,6 @@ #include "mpc10x.h" -static struct mtd_partition linkstation_physmap_partitions[] = { - { - .name = "mtd_firmimg", - .offset = 0x000000, - .size = 0x300000, - }, - { - .name = "mtd_bootcode", - .offset = 0x300000, - .size = 0x070000, - }, - { - .name = "mtd_status", - .offset = 0x370000, - .size = 0x010000, - }, - { - .name = "mtd_conf", - .offset = 0x380000, - .size = 0x080000, - }, - { - .name = "mtd_allflash", - .offset = 0x000000, - .size = 0x400000, - }, - { - .name = "mtd_data", - .offset = 0x310000, - .size = 0x0f0000, - }, -}; - static __initdata struct of_device_id of_bus_ids[] = { { .type = "soc", }, { .compatible = "simple-bus", }, @@ -99,10 +65,6 @@ static int __init linkstation_add_bridge(struct device_node *dev) static void __init linkstation_setup_arch(void) { struct device_node *np; -#ifdef CONFIG_MTD_PHYSMAP - physmap_set_partitions(linkstation_physmap_partitions, - ARRAY_SIZE(linkstation_physmap_partitions)); -#endif /* Lookup PCI host bridges */ for_each_compatible_node(np, "pci", "mpc10x-pci") diff --git a/arch/powerpc/platforms/embedded6xx/storcenter.c b/arch/powerpc/platforms/embedded6xx/storcenter.c index 8864e488498..613070e9ddb 100644 --- a/arch/powerpc/platforms/embedded6xx/storcenter.c +++ b/arch/powerpc/platforms/embedded6xx/storcenter.c @@ -14,7 +14,6 @@ #include #include #include -#include #include #include @@ -26,32 +25,6 @@ #include "mpc10x.h" -#ifdef CONFIG_MTD_PHYSMAP -static struct mtd_partition storcenter_physmap_partitions[] = { - { - .name = "kernel", - .offset = 0x000000, - .size = 0x170000, - }, - { - .name = "rootfs", - .offset = 0x170000, - .size = 0x590000, - }, - { - .name = "uboot", - .offset = 0x700000, - .size = 0x040000, - }, - { - .name = "config", - .offset = 0x740000, - .size = 0x0c0000, - }, -}; -#endif - - static __initdata struct of_device_id storcenter_of_bus[] = { { .name = "soc", }, {}, @@ -96,11 +69,6 @@ static void __init storcenter_setup_arch(void) { struct device_node *np; -#ifdef CONFIG_MTD_PHYSMAP - physmap_set_partitions(storcenter_physmap_partitions, - ARRAY_SIZE(storcenter_physmap_partitions)); -#endif - /* Lookup PCI host bridges */ for_each_compatible_node(np, "pci", "mpc10x-pci") storcenter_add_bridge(np); -- cgit v1.2.2 From ba087e6f69381de6c91d6634aa0f603a2fdc96a9 Mon Sep 17 00:00:00 2001 From: Nobuhiro Iwamatsu Date: Fri, 6 Mar 2009 02:51:14 +0000 Subject: sh: Add media/soc_camera.h to board setup of Renesas AP325RXA Other compilation errors were revised by commit of "sh: ap325rxa: Revert ov772x support" (08c2f5b4d76f83213e379b12df504269d21c9e7c) but other compilation errors are given. We revert this commit and need to add new header(media/soc_camera.h). This change revises new compilation error. Signed-off-by: Nobuhiro Iwamatsu Signed-off-by: Paul Mundt --- arch/sh/boards/board-ap325rxa.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/sh/boards/board-ap325rxa.c b/arch/sh/boards/board-ap325rxa.c index 72da416f616..15b6d450fbf 100644 --- a/arch/sh/boards/board-ap325rxa.c +++ b/arch/sh/boards/board-ap325rxa.c @@ -22,6 +22,7 @@ #include #include #include +#include #include #include #include