| Commit message (Collapse) | Author | Age |
|
|
|
|
|
|
|
|
|
|
|
| |
Currently the IOs are returned back in slot reset, this
could be late and can cause error handler to invoke.
If error handler invokes, eh_abort fails and escalate to
device/bus/host resets causing issues.
The commands need to be returned back to upper layer in
io_error_detected.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
| |
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
| |
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
| |
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
| |
fail.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
| |
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We have been seeing the flush request timeout with a wide
range of hardware from tgt+iser to FC targets from a major vendor.
After discussions about if the value should be configurable and
what the best value should be, this patch just increases the flush/sync
cache timeout to 1 minute. 2 minutes was determined to be too long, and
making it configurable was troublesome for users.
This patch was made over Linus's tree. It is not made over scsi-misc
or scsi-rc-fixes, because Linus's had block layer changes that my
patch was built over.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
| |
Also updated maintainer info.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
In the case when an ep_connect request is interrupted due to route
request stall, if the iSCSI daemon is terminated by the user, the chip
will be left in a state which will not get cleaned up upon module
removal. Upon module reload, when the same context id is used for a
new connection, chip panic would occur.
This patch adds chip cleanup in the module removal path.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specific to the Broadcom 10g chipset, the CFC delete operation must be
coupled with the cm_abort/close with does the SRC delete/terminate offload
operation prior.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Acked-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
| |
Expanded the TMF request routine to support other TMFs such as LUN
RESET, etc.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
| |
According to RFC3720, nopout packet sent in response to unsolicited
nopin packet requesting a response must retain the TTT of the requester.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
| |
Bump the driver version.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
| |
This patch fixes a resource address formatting problem where the first byte
was being zeroed out.
Also, the device ID is now made available as a sysfs attribute.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
| |
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Added cxgb4i iSCSI driver.
This patch implements the cxgb4i iscsi connection acceleration for the
open-iscsi initiator.
The cxgb4i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
[PATCH v5 1/3] libcxgbi: common library for cxgb3i and cxgb4i
From: Karen Xie <kxie@chelsio.com>
Extracts common functions to libcxgbi.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
In lpfc_cleanup_pending_mbox() we already have IRQs disabled so we don't
need to disable them again.
Also in lpfc_sli_intr_handler() there is a typo where it has
spin_unlock_irq() instead of just spin_unlock().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Patch has only been compile tested.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
| |
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Patch has only been compile tested.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
| |
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
| |
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds a fc_host setting to store the
default dev_loss_tmo. It is used if the driver
has a callack to get the value from the LLD. If
the callback is not set, then we use the fc class
module default value.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
gcc-4.0.2:
drivers/scsi/qla4xxx/ql4_os.c: In function 'qla4_8xxx_error_recovery':
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2377: sorry, unimplemented: called from here
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2393: sorry, unimplemented: called from here
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
| |
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (28 commits)
[SCSI] qla4xxx: fix compilation warning
[SCSI] make error handling more robust in the face of reservations
[SCSI] tgt: fix warning
[SCSI] drivers/message/fusion: Adjust confusing if indentation
[SCSI] Return NEEDS_RETRY for eh commands with status BUSY
[SCSI] ibmvfc: Driver version 1.0.9
[SCSI] ibmvfc: Fix terminate_rport_io
[SCSI] ibmvfc: Fix rport add/delete race resulting in oops
[SCSI] lpfc 8.3.16: Change LPFC driver version to 8.3.16
[SCSI] lpfc 8.3.16: FCoE Discovery and Failover Fixes
[SCSI] lpfc 8.3.16: SLI Additions, updates, and code cleanup
[SCSI] pm8001: introduce missing kfree
[SCSI] qla4xxx: Update driver version to 5.02.00-k3
[SCSI] qla4xxx: Added AER support for ISP82xx
[SCSI] qla4xxx: Handle outstanding mbx cmds on hung f/w scenarios
[SCSI] qla4xxx: updated mbx_sys_info struct to sync with FW 4.6.x
[SCSI] qla4xxx: clear AF_DPC_SCHEDULED flage when exit from do_dpc
[SCSI] qla4xxx: Stop firmware before doing init firmware.
[SCSI] qla4xxx: Use the correct request queue.
[SCSI] qla4xxx: set correct value in sess->recovery_tmo
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fix following warning:
drivers/scsi/qla4xxx/ql4_nx.c: In function 'qla4_8xxx_get_flash_info':
drivers/scsi/qla4xxx/ql4_nx.c:1952: warning: 'mid' may be used uninitialized in this function
drivers/scsi/qla4xxx/ql4_nx.c:1952: note: 'mid' was declared here
drivers/scsi/qla4xxx/ql4_nx.c:1952: warning: 'fid' may be used uninitialized in this function
drivers/scsi/qla4xxx/ql4_nx.c:1952: note: 'fid' was declared here
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
commit 5f91bb050ecc4ff1d8d3d07edbe550c8f431c5e1
Author: Michael Reed <mdr@sgi.com>
Date: Mon Aug 10 11:59:28 2009 -0500
[SCSI] reservation conflict after timeout causes device to be taken offline
Flipped us from always returning failed to always returning success in
the name of fixing the problem where reservation conflict returns from
test unit ready cause the device always to be taken offline.
Unfortuantely, it also introduced a problem whereby for commands other
than test unit ready, the eh dispatcher thinks they succeeded when
reservation conflict is returned, whereas in reality they failed. Fix
this by only returning success for the test unit ready case.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Using scsi_tgt_lib in a new target module, we were getting
the following warning and a stack traceback on every I/O completion:
WARNING: at block/blk-core.c:1108
Which is claiming we may be leaking a bio.
We don't leak bios (blk_rq_unmap_user should free them).
Set rq->bio to NULL before calling scsi_host_put_command().
This was as advised by Fujita Tomonori.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
When the transport is busy and we're sending an EH command drivers
occasionally return 'BUSY'. As this in most cases is the TUR
command sent as part of the error recovery this is a sure way
to make the error recovery escalate. Returning 'NEEDS_RETRY'
here will just retry the TUR command and eventually abort the
original command, thus making error handling far smoother.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| | |
Bump driver version.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The ibmvfc driver was incorrectly obtaining a scsi_target pointer
from an fc_rport. The way it is coded ensures that ibmvfc's
terminate_rport_io handler does absolutely nothing. Fix this up
to iterate through affected devices differently, sending cancel
and abort task set as appropriate. Without this patch,
fast_io_fail_tmo is broken for ibmvfc.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit 43c8da907ccc656935d1085701f4db83385d8a59 introduced a race
condition which can occur when adding/deleting rports. There are
two possible threads now that can be deleting rports in the ibmvfc
driver, which can result in list_del being called twice, resulting
in an oops. This patch adds a new state to the ibmvfc_target struct
to indicate the target has been removed from the list and is in
the process of being deleted.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| | |
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
- Add support for re-reg'ing changed VPI w/o unregister VPI
- Copy WWN and state from old nodelist when target DID change.
- Clean up old nodelist rport and put the nodelist when target DID change.
- Clear the VFI_REGISTERED flag when UNREG_VFI completes.
- Made both checks of port_state against LPFC_FLOGI and LPFC_FDISC
non-inclusive for ignoring CVL events.
- Added logic to stop retrying of the ongoing PLOGI and FDISC if
transitioned back to the FCF rediscovery state in reaction to CVL.
- Removed the dependency of scanning of all the available FCF table
entries for bulding round-robin bitmap.
- Use the lpfc_sli4_fcf_rr_read_fcf_rec() in responding to
individual New FCF found event.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
- Remove unneeded Endian swap for Block Guard IOCB response
- Add a check for mailbox active before issuing the heartbeat command
- Correct heartbeat last_completion updates to avoid unneeded heartbeats
- Add Security crypto support to CONFIG_PORT mailbox command
- Add fips level and fips spec revision sysfs parameters
- Remove duplicate setting of ext_byte_len fields in lpfc_bsg_issue_mbox
- Switch call to memcpy_toio to __write32_copy to prevent unaligned 64 bit copy
- Change log message 0318 from an error to a warning as it is not an error
- Patch an incorrect call to lpfc_drain_txq on SLI-3 functions
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
identifier f,f1;
position p1,p2;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
<... when != x
when != if (...) { <+...x...+> }
when != (x) == NULL
when != (x) != NULL
when != (x) == 0
when != (x) != 0
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return <+...x...+>;
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: jack wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| | |
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Added support for PCI error handling
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Outstanding mailbox commands, have no way to recover on f/w hung, and we
timeout on waiting for mbx response. This in turn affects the recovery process
as follows:
- We might already be in dpc while waiting for mbx to complete, so recovery for
that pci function will never get invoked. Reset Timeout (10 sec) is far less
than mbx timeout (30 sec).
- Other mbx cmds will get stuck due to serial mbx access.
Solution is to identify fw-hung scenario and handle outstanding mbx commands to
have an early-exit instead of waiting for response.
Other mbx commands waiting for access will also do an early-exit if fw-hung is
still applicable.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Also, changed boundary checking from size of total
structure to verification that we received the amount of
data needed to cache inernally. This change will provide
compatibility with mbx_sys_info structure sizes in both
older and newer firmware versions.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| | |
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
If BIOS is enabled then drivers init firmware fails since
BIOS has done the init once.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| | |
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| | |
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The rport port state and flags are set under the host lock,
so this patch calls fc_remote_port_chkready with the host lock
held like is also done in the other fc drivers.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Fake "address-of" expressions that evaluate to NULL generally confuse
readers and can provoke compiler warnings. This patch (as1411)
removes one such fake expression introduced by:
commit db5bd1e0b505c54ff492172ce4abc245cf6cd639
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Thu Jun 17 10:36:49 2010 -0400
[SCSI] convert to the new PM framework
using an "#ifdef" in its place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
iscsi_boot_sysfs does not depend on firmware. Any iscsi driver
can use it. This patch moves iscsi_boot_sysfs to the scsi
dir, so that it can be used on any arch with any driver.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Acked-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
be2iscsi uses iscsi_boot_*() interfaces, so it should ensure that
ISCSI_BOOT_SYSFS is enabled.
ERROR: "iscsi_boot_create_target" [drivers/scsi/be2iscsi/be2iscsi.ko] undefined!
ERROR: "iscsi_boot_create_ethernet" [drivers/scsi/be2iscsi/be2iscsi.ko] undefined!
ERROR: "iscsi_boot_create_host_kset" [drivers/scsi/be2iscsi/be2iscsi.ko] undefined!
ERROR: "iscsi_boot_create_initiator" [drivers/scsi/be2iscsi/be2iscsi.ko] undefined!
ERROR: "iscsi_boot_destroy_kset" [drivers/scsi/be2iscsi/be2iscsi.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|