aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net
Commit message (Collapse)AuthorAge
* ath9k: Fix rx data corruptionVasanthakumar Thiagarajan2009-09-23
| | | | | | | | Setting bit 20 and 25 of 0x8344 can cause occasional rx data corruption, clear them to fix this issue. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix chip wakeup issueSujith2009-09-23
| | | | | | | | | Waking up the chip after powering it down fails sometimes. In this case the CPU is locked for 200ms. Reduce this interval to 10ms to avoid excessive busy looping. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Restore TSF after RESETSujith2009-09-23
| | | | | | | | For chips requiring RTC reset, TSF has to be restored after power on reset. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Revamp PCIE workaroundsVivek Natarajan2009-09-23
| | | | | | | | | | | | | * Disable L1 state ONLY when device is in D3 mode. * Clear bit 22 of register 0x4004. * Handle power on/off properly Not setting the workarounds properly resulted in the disappearance of the card in certain cases. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Set default noise floor value for AR9287Vivek Natarajan2009-09-23
| | | | | | | | | The default noise floor was never initialized for AR9287.This patch helps in reporting the correct RSSI for this version of chipset. Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Implement RFKILL status for LP PHYLarry Finger2009-09-23
| | | | | | | | The LP (and probably N) PHY has the same radio disabled bit as the higher-revision A and G PHYs. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Remove BROKEN attribute from SDIOMichael Buesch2009-09-23
| | | | | | | | SDIO works (more or less), so remove the BROKEN dependency and let people test it. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: fix build error if !CONFIG_B43_LEDSAlbert Herranz2009-09-23
| | | | | | | | | | | | | Fix the following build error when CONFIG_B43_LEDS is not selected: drivers/net/wireless/b43/main.c: In function 'b43_remove': drivers/net/wireless/b43/main.c:4990: error: 'struct b43_leds' has no member named 'stop' drivers/net/wireless/b43/main.c:4991: error: 'struct b43_leds' has no member named 'work' make[4]: *** [drivers/net/wireless/b43/main.o] Error 1 Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Don't abuse wl->current_dev in the led workMichael Buesch2009-09-23
| | | | | | | | | | Don't abuse wl->current_dev in the LED work for checking whether we're going down. Add an explicit variable. This fixes a crash on rmmod dereferencing the wl->current_dev NULL pointer in various other places of the driver. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Add LP PHY Analog Switch SupportThomas Ilnseher2009-09-23
| | | | | | | | | | | | | | | | | The current verison of b43 uses "b43_phyop_switch_analog_generic" for A, G and LP phys. According to the spec, this is the wrong behaviour for the LP PHY (see: http://bcm-v4.sipsolutions.net/802.11/PHY/Anacore ) While no problems on the x86 plattform where seen, this leads to a crash on the BCM5354 SoC (MIPS 32 LE plattform). This patch implements the analog switch for LP PHYs according to the specs. It fixes the crash signed-off-by: Thomas Ilnseher <illth@gmx.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Disable PMQ mechanismMichael Buesch2009-09-23
| | | | | | | | This reduces IRQ pressure by about one third on a saturated link by disabling the PMQ mechanism. We currently don't use that mechanism. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Add optional verbose runtime statisticsMichael Buesch2009-09-23
| | | | | | | | | | This adds support for verbose runtime statistics. It defaults to off and must be enabled in debugfs, if desired. The first measurement may be incorrect, because statistics are not cleared after they got enabled through debugfs. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Fix IRQ sync for SDIOMichael Buesch2009-09-23
| | | | | | | | synchronize_irq is meaningless for SDIO. sdio_release_irq will sync the IRQ thread for us. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Fix SDIO interrupt handler deadlockMichael Buesch2009-09-23
| | | | | | | We need to release the SDIO host before locking the driver mutex. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Do not use _irqsafe callbacksMichael Buesch2009-09-23
| | | | | | | We don't need to call the irqsafe callbacks. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Add Soft-MAC SDIO device supportAlbert Herranz2009-09-23
| | | | | | | | | | This adds support for Soft-MAC SDIO devices to b43. The driver still lacks some fixes for SDIO devices, so it's currently marked as BROKEN. Signed-off-by: Albert Herranz <albert_herranz@yahoo.es> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Rewrite suspend/resume codeMichael Buesch2009-09-23
| | | | | | | | | This removes most of the b43 suspend/resume code (it's handled by mac80211) and moves the registration of devices to the attachment phase. This is required, because we must not register/unregister devices on suspend/resume. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* p54usb: add Zcomax XG-705A usbidChristian Lamparter2009-09-23
| | | | | | | | | This patch adds a new usbid for Zcomax XG-705A to the device table. Cc: stable@kernel.org Reported-by: Jari Jaakola <jari.jaakola@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: disable powersave for 4965Johannes Berg2009-09-23
| | | | | | | | | | | | | | | | | | | | There's a bug in 4965 powersave that appears to be related to the way it keeps track of its data during sleep, but we haven't found it yet. Due to that, using powersave may spontaneously cause the device to SYSASSERT when transitioning from sleep to wake. Therefore, disable powersave for 4965, until (if ever, unfortunately) we can identify and fix the problem. Cf. http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1982 which was closed, but now has re-appeared with IDLE mode, which probably means we never really fixed it. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: find the correct first antennaWey-Yi Guy2009-09-23
| | | | | | | | | | | We can not assume antenna "A" is the first valid anttena for all the NIC. Need to make sure choice the correct antenna based on h/w configuration for transmit to avoid sending frame on invalid antenna Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: fix potential rx buffer lossReinette Chatre2009-09-23
| | | | | | | | | | | | | | | | | | RX handling maintains a few lists that keep track of the RX buffers. Buffers move from one list to the other as they are used, replenished, and again made available for usage. In one such instance, when a buffer is used it enters the "rx_used" list. When buffers are replenished an skb is attached to the buffer and it is moved to the "rx_free" list. The problem here is that the buffer is first removed from the "rx_used" list _before_ the skb is allocated. Thus, if the skb allocation fails this buffer remains removed from the "rx_used" list and is thus lost for future usage. Fix this by first allocating the skb before trying to attach it to a list. We add an additional check to not do this unnecessarily. Reported-by: Rick Farrington <rickdic@hotmail.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* iwlwifi: fix HT operation in 2.4 GHz bandDaniel C Halperin2009-09-23
| | | | | | | | | | | When we cleaned up the driver to properly tell mac80211 about HT rates ("iwlwifi: use iwl_hwrate_get_mac80211_idx where appropriate"), we broke internal rate indexing in 2.4 GHz band. Signed-off-by: Daniel C Halperin <daniel.c.halperin@intel.com> Tested-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Fix resume failureMichael Buesch2009-09-23
| | | | | | | | | | | | This fixes a resume failure where a signal is pending on resume so the firmware upload fails. This removes the interruptible sleep, because we don't really need it. In the worst case (with broken firmware) the sleep loop will take 1 second. In the common case (working firmware), it will only take a few milliseconds. So we don't really need to be interruptible. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* wireless: default CONFIG_WLAN to yLuis R. Rodriguez2009-09-23
| | | | | | | | | When this was added no defaults were set and it seems this implies n. Default this to y. Reported-by: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* ath9k: Fix bug in ANI channel handlingSujith2009-09-23
| | | | | | | | | | When processing MIB interrupts, OFDM and CCK error handling routines for low RSSI values have to be invoked only when the channel mode is 11G/11B. Since HT channels will also fall under the bands 2Ghz/5Ghz, check appropriately. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* b43: Force-wake queues on initMichael Buesch2009-09-23
| | | | | | | | | Force wake the mac80211 queues on init. Under rare circumstances they may be stopped, if a DMA error or something else causes a device reset while a queue was stopped. Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* hostap: Revert a toxic part of the conversion to net_device_opsMartin Decky2009-09-23
| | | | | | | | | | | | | | | As the hostap driver was converted to use net_device_ops, a mistake was made in hostap_main.c (commit 5ae4efbcd2611562a8b93596be034e63495706a5). Originally, the tx_queue_len was set to 0 for every other interface than HOSTAP_INTERFACE_MASTER, but the new fragment of code sets tx_queue_len to 0 only for HOSTAP_INTERFACE_MASTER. The opposite of the previous behavior makes the driver to drop all packets in AP mode. Change the way 0 is assigned to tx_queue_len according to the original logic. Signed-off-by: Martin Decky <martin@decky.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds2009-09-14
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits) netxen: update copyright netxen: fix tx timeout recovery netxen: fix file firmware leak netxen: improve pci memory access netxen: change firmware write size tg3: Fix return ring size breakage netxen: build fix for INET=n cdc-phonet: autoconfigure Phonet address Phonet: back-end for autoconfigured addresses Phonet: fix netlink address dump error handling ipv6: Add IFA_F_DADFAILED flag net: Add DEVTYPE support for Ethernet based devices mv643xx_eth.c: remove unused txq_set_wrr() ucc_geth: Fix hangs after switching from full to half duplex ucc_geth: Rearrange some code to avoid forward declarations phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs drivers/net/phy: introduce missing kfree drivers/net/wan: introduce missing kfree net: force bridge module(s) to be GPL Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded ... Fixed up trivial conflicts: - arch/x86/include/asm/socket.h converted to <asm-generic/socket.h> in the x86 tree. The generic header has the same new #define's, so that works out fine. - drivers/net/tun.c fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that switched over to using 'tun->socket.sk' instead of the redundantly available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks to the TUN driver") which added a new 'tun->sk' use. Noted in 'next' by Stephen Rothwell.
| * netxen: update copyrightDhananjay Phadke2009-09-11
| | | | | | | | | | | | | | | | | | o Add QLogic copyright, add linux-driver@qlogic.com to MAINTAINERS. o Delete old contact information. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * netxen: fix tx timeout recoveryAmit Kumar Salecha2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Redesign tx timeout handling in line with new firmware reset design that co-ordinates with other PCI function drivers. o For NX3031, first try to reset PCI function's own context before requesting firmware reset. o For NX2031, since firmware heartbit is not supported directly request firmware reset. Signed-off-by: Amit Kumar Salecha <amit@netxen.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * netxen: fix file firmware leakDhananjay Phadke2009-09-11
| | | | | | | | | | | | | | Release file firmware when no firmware reset is required. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * netxen: improve pci memory accessDhananjay Phadke2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | o Access on card memory through memory controller (agent) rather than moving small pci window around. Clean up the code for moving windows around. o Restrict memory accesss to 64 bit, currently only firmware download uses this. Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * netxen: change firmware write sizeAmit Kumar Salecha2009-09-11
| | | | | | | | | | | | | | | | | | | | Use 8 byte strides for firmware download into card memory since oncard memory controller needs 8 byte (64 bit) accesses. This avoids unnecessary rmw cycles. Signed-off-by: Amit Kumar Salecha <amit@netxen.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * tg3: Fix return ring size breakageMatt Carlson2009-09-11
| | | | | | | | | | | | | | | | | | | | Commit f6eb9b1fc1411d22c073f5264e5630a541d0f7df, "tg3: Add 5717 asic rev" changed how the rx return ring size operations are done. It effectively inverts the sense of the previous test, but it failed to also invert the resulting sizes. This patch corrects that error. Signed-off-by: Matt Carlson <mcarlson@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * netxen: build fix for INET=nRandy Dunlap2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | When CONFIG_INET is disabled, netxen has a build failure: netxen_nic_main.c:(.text+0x118fd1): undefined reference to `netxen_config_indev_addr' so make that function just an empty stub when CONFIG_INET=n. (not "inline" since that conflicts with other declarations of it) Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * cdc-phonet: autoconfigure Phonet addressRémi Denis-Courmont2009-09-11
| | | | | | | | | | Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: Add DEVTYPE support for Ethernet based devicesMarcel Holtmann2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Ethernet framing is used for a lot of devices these days. Most prominent are WiFi and WiMAX based devices. However for userspace application it is important to classify these devices correctly and not only see them as Ethernet devices. The daemons like HAL, DeviceKit or even NetworkManager with udev support tries to do the classification in userspace with a lot trickery and extra system calls. This is not good and actually reaches its limitations. Especially since the kernel does know the type of the Ethernet device it is pretty stupid. To solve this problem the underlying device type needs to be set and then the value will be exported as DEVTYPE via uevents and available within udev. # cat /sys/class/net/wlan0/uevent DEVTYPE=wlan INTERFACE=wlan0 IFINDEX=5 This is similar to subsystems like USB and SCSI that distinguish between hosts, devices, disks, partitions etc. The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual device type. All device types are free form, but for convenience the same strings as used with RFKILL are choosen. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
| * mv643xx_eth.c: remove unused txq_set_wrr()Mikael Pettersson2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | The txq_set_wrr() function in drivers/net/mv643xx_eth.c is unused, not even referenced under #if 0 or something like that, which results in a compile-time warning: drivers/net/mv643xx_eth.c:1070: warning: 'txq_set_wrr' defined but not used Fix: remove it. Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
| * ucc_geth: Fix hangs after switching from full to half duplexAnton Vorontsov2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MPC8360 QE UCC ethernet controllers hang when changing link duplex under a load (a bit of NFS activity is enough). PHY: mdio@e0102120:00 - Link is Up - 1000/Full sh-3.00# ethtool -s eth0 speed 100 duplex half autoneg off PHY: mdio@e0102120:00 - Link is Down PHY: mdio@e0102120:00 - Link is Up - 100/Half NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out ------------[ cut here ]------------ Badness at c01fcbd0 [verbose debug info unavailable] NIP: c01fcbd0 LR: c01fcbd0 CTR: c0194e44 ... The cure is to disable the controller before changing speed/duplex and enable it afterwards. Though, disabling the controller might take quite a while, so we better not grab any spinlocks in adjust_link(). Instead, we quiesce the driver's activity, and only then disable the controller. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * ucc_geth: Rearrange some code to avoid forward declarationsAnton Vorontsov2009-09-11
| | | | | | | | | | | | | | | | | | | | | | We'll need ugeth_disable() and ugeth_enable() calls earlier in the file, so rearrange some code to avoid forward declarations. The patch doesn't contain any functional changes. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYsAnton Vorontsov2009-09-11
| | | | | | | | | | | | | | | | | | According to specs, when auto-negotiation is disabled, Marvell PHYs need a software reset after changing speed/duplex forcing bits. Otherwise, the modified bits have no effect. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * drivers/net/phy: introduce missing kfreeJulia Lawall2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Error handling code following a kzalloc should free the allocated data. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
| * drivers/net/wan: introduce missing kfreeJulia Lawall2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Error handling code following a kmalloc should free the allocated data. The semantic match that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
| * Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loadedArnaldo Carvalho de Melo2009-09-11
| | | | | | | | | | | | | | | | | | | | | | | | And also do a better job of returning proper NET_{RX,XMIT}_ values. Based on a patch and suggestions by Mark Smith. This fixes CVE-2009-2903 Reported-by: Mark Smith <lk-netdev@lk-netdev.nosense.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * dm9000: Use resource_size instead of private macroTobias Klauser2009-09-09
| | | | | | | | | | | | | | | | The macro res_size in drivers/net/dm9000.c is a copy of resource_size in linux/ioport.h. Remove the function and use resource_size instead. Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * dm9000: Remove unnecessary memset of netdev private dataTobias Klauser2009-09-09
| | | | | | | | | | | | | | | | | | The memory for the private data is allocated using kzalloc in alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to set it to 0 again. Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
| * netxen: fix tx descriptor structureAmit Kumar Salecha2009-09-09
| | | | | | | | | | | | | | | | Fix the offset of vlan_TCI field in cmd_desc_type0. Signed-off-by: Amit Kumar Salecha <amit@qlogic.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * netxen: fix check for ip addr hashing supportAmit Kumar Salecha2009-09-09
| | | | | | | | | | | | | | | | | | Fix typo in checking dest ip has support before programming destip addresses. Signed-off-by: Amit Kumar Salecha <amit@netxen.com> Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge branch 'master' of ↵David S. Miller2009-09-09
| |\ | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
| | * ath9k: Initialize the priority gpio for BT coex 3-wireVasanthakumar Thiagarajan2009-09-09
| | | | | | | | | | | | | | | | | | | | | | | | Oops, a stupid mistake in the original patch which adds coex 3-wire support. Bluetooth priority gpio needs to be gpio 7. Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-10-23 16:41:34 -0400