aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/rt2x00/rt2800.h
Commit message (Collapse)AuthorAge
* rt2x00: Add debugfs access for rfcsr registerAnisse Astier2012-05-08
| | | | | | | | | | RFCSR is only used in rt2800. For other chipsets, the debug struct for rfcsr should be zeroed, which isn't be an issue, since the code can now cope with that. Signed-off-by: Anisse Astier <anisse@astier.eu> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2800: add chipset revision RT5390R supportAnisse Astier2012-04-23
| | | | | | | | | | | | | | | | | | | About 70% of the chips with revision RT5390R initialize incorrectly, using the auxiliary antenna instead of the main one. The net result is that signal reception is very poor (no AP further than 1M). This chipset differs from RT5390 and RT5390F by its support of hardware antenna diversity. Therefore antenna selection should be done differently, by disabling software features and previously selected antenna. This changeset does just that, and makes all RT5390R work properly. This is based on Ralink's 2012_03_22_RT5572_Linux_STA_v2.6.0.0_DPO driver. Signed-off-by: Anisse Astier <anisse@astier.eu> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2800: debugfs register access: BBP is 256 bytes bigAnisse Astier2012-04-23
| | | | | | | | | We're already using BBP for values > 128. Make that explicit and allow debugfs access. Signed-off-by: Anisse Astier <anisse@astier.eu> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix beacon skew in rt2800pciHelmut Schaa2012-03-12
| | | | | | | | | | | | | | | | rt2800pci is suffering from beacon skew in AP mode. Some powersaving clients (like VOIP phones) are getting into trouble after some time when the beacon skew is getting too big. The ralink legacy drivers contain a function that indicates that the beacon timer is off by 1us per tbtt. And this function works around that by reducing the beacon interval for every 64th beacon transmission by 64us (the smallest possible value). Do the same in rt2800pci. This allows proper powersaving when rt2800pci is used in AP mode. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2800: Add documentation on MCU requestsJakub Kicinski2012-02-27
| | | | | | | | | | Add documentation on MCU communication, some of known commands and their arguments. Supplement command ids. Signed-off-by: Jakub Kicinski <kubakici@wp.pl> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00:Add RT5372 chipset supportJohn Li2012-02-27
| | | | | | | Signed-off-by: John Li <chen-yang.li@mediatek.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00:Add VCO recalibrationJohn Li2012-02-27
| | | | | | | Signed-off-by: John Li <chen-yang.li@mediatek.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Correctly set txmixer_gain in RT3572 channel switching.Gertjan van Wingerde2012-02-08
| | | | | | | | | | | | Align with the v2.5.0.0 Ralink RT3572 driver. Save the EEPROM txmixer_gain values inside the rt2800 driver data structure and use it throughout the code. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix RT3572 channel switch RFCSR 7 programming.Gertjan van Wingerde2012-02-08
| | | | | | | | | Align with the v2.5.0.0 Ralink RT3572 driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Use saved BBP 25 and 26 values when configuring channel on RT3572.Gertjan van Wingerde2012-02-08
| | | | | | | | | This brings the rt2800 channel switching code for RT3572 closer to the v2.5.0.0 Ralink RT3572 driver. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Use struct rt2x00_dev driver data in rt2800{pci,usb}.Gertjan van Wingerde2012-02-08
| | | | | | | | | Start using the struct rt2x00_dev driver data in rt2800 for the calibration data. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2800: document RF_R03 register bits [7:4]Stanislaw Gruszka2012-02-06
| | | | | | | | | | Taken from: 2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO (based on function RT33xx_ChipSwitchChannel) Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2800: radio 3xxxx: channel switch RX/TX calibration fixesStanislaw Gruszka2012-02-06
| | | | | | | | | | | | | | | Synchronize code with Ralink driver: 2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO Based on functions: RT30xx_ChipSwitchChannel RT33xx_ChipSwitchChannel NICInitRT3370RFRegisters and defines from: include/chip/rt33xx.h Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2800: radio 3xxx: reprogram only lower bits of RF_R3Stanislaw Gruszka2012-02-06
| | | | | | | | | | Synchronize code with Ralink driver: 2011_0719_RT3070_RT3370_RT5370_RT5372_Linux_STA_V2.5.0.3_DPO (functions: RT33xx_ChipSwitchChannel() and RT30xx_ChipSwitchChannel()) Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Change RF3853 to RF3053.Gertjan van Wingerde2012-01-04
| | | | | | | | | According to the latest Ralink vendor drivers, this seems to be the real RF chipset type. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add LED_CFG register descriptionHelmut Schaa2011-09-14
| | | | | | | Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add support for RT3572/RT3592/RT3592+Bluetooth combo cardGertjan van Wingerde2011-06-01
| | | | | | | | | | | (based on an earlier patch submitted by Shiang) Add support for RT3572/RT3592/RT3592+Bluetooth combo card Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge branch 'master' of ↵John W. Linville2011-05-16
|\ | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: drivers/net/wireless/iwlwifi/iwl-agn-tx.c net/mac80211/sta_info.h
| * rt2x00: Initial support for RT5370 USB devices.Gertjan van Wingerde2011-05-05
| | | | | | | | | | | | | | | | | | Add necessary RF chipset define and basic support for these devices. Tested-by: Juan Carlos Garza <juancarlosgarza@gmail.com> Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | Merge branch 'master' of ↵John W. Linville2011-04-12
|\| | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: drivers/net/wireless/ath/ar9170/main.c drivers/net/wireless/ath/ar9170/phy.c drivers/net/wireless/zd1211rw/zd_rf_rf2959.c
| * rt2x00: Implement tx power temperature compensationHelmut Schaa2011-04-04
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | rt2800 devices should adjust their tx power in accordance with the eeproms temperature calibration values. Add a new driver callback gain_calibration that is called every 4 seconds. The rt2800 gain calibration routine simply runs the tx power configuration that takes care of calculating the temperature compensation delta. We don't need to synchronize the calls to rt2800_config_txpower as they should all happen from mac80211's single threaded workqueue. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* | Fix common misspellingsLucas De Marchi2011-03-31
|/ | | | | | Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
* rt2x00: fix whitespace damage in the rt2800 specific codeGabor Juhos2011-03-04
| | | | | | | | | | | | The rt2800 specific code contains a lots of whitespace damage caused by the commit 'rt2x00: Add support for RT5390 chip'. This patch fixes those whitespace errors. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add support for RT5390 chipRA-Shiang Tu2011-02-21
| | | | | | | | Add new RT5390 chip support Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add/Modify the GPIO register definitionShiang Tu2011-02-21
| | | | | | | | Revise/Add GPIO register related definitions Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add/Modify protection related register definitionsShiang Tu2011-02-21
| | | | | | | | | | Make the definition of protection related registers more precisely Signed-off-by: Shiang Tu <shiang_tu@ralinktech.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix rt2800 txpower setting to correct valueRA-Jay Hung2011-02-21
| | | | | | | | | | | TX_PWR_CFG_* setting need to consider below cases -compesate 20M/40M tx power delta for 2.4/5GHZ band -limit maximum EIRP tx power to power_level of regulatory requirement Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add antenna setting for RT3070/RT3090/RT3390 with RX antenna ↵RA-Jay Hung2011-02-21
| | | | | | | | | | | | | | | | diversity support For RT3070/RT3090/RT3390 with RX antenna diversity support, we must select default antenna using gpio control way even if we do not turn on antenna diversity feature. Seperate the meaning of TX/RX chain and antenna. Some chips use 2x2 TX/RX chain but may have 3 RX antennas or 1x1 TX/RX chain but may have 2 RX antennas to do antenna diversity. Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Correct initial value of US_CYC_CNT register for pcie interfaceRA-Jay Hung2011-01-31
| | | | | | | | | | CLOCK CYCLE: Clock cycle count in 1us PCI:0x21, PCIE:0x7d, USB:0x1e Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix and fine-tune rf registers for RT3070/RT3071/RT3090RA-Jay Hung2011-01-19
| | | | | | | | | | Basically fix and fine-tune RT3070/RT3071/RT3090 chip RF initial value when call rt2800_init_rfcsr Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix WMM Queue namingIvo van Doorn2010-12-13
| | | | | | | | | | | | | | | | | The Queue names were incorrectly copied from the legacy drivers, as a result the queue names were inversed to what was expected. This renames the queues using this mapping: QID_AC_BK -> QID_AC_VO (priority 0) QID_AC_BE -> QID_AC_VI (priority 1) QID_AC_VI -> QID_AC_BE (priority 2) QID_AC_VO -> QID_AC_BK (priority 3) Note that this was a naming problem only, which didn't affect the assignment of frames to their respective queues. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add RF chip definitionRA-Jay Hung2010-12-13
| | | | | | | | Add RF chip definition Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Implement get_survey callback for rt2800Helmut Schaa2010-12-13
| | | | | | | | | Implement the get_survey callback to allow user space to read statistics about the current channel condition. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add rt2800 EEPROM definitionRA-Jay Hung2010-12-13
| | | | | | | | | Add and modify NIC Configuration and LED definition of EEPROM Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add initial support for RT3370/RT3390 devices.Gertjan van Wingerde2010-11-17
| | | | | | | | | Modified from Eddy's patch by adding the RT3370 USB support as well. Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com> Cc: Eddy Tsai <Eddy_Tsai@ralinktech.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add watchdog functions for HW queueIvo van Doorn2010-11-15
| | | | | | | | | | | | | | | Add watchdog functions for managing the Queues inside the hardware. Normally the driver doesn't have much to do with these queues directly, but the Ralink drivers did implement watchdog functions for these. These watchdog functions are not triggered that often, compared to the other watchdog functions, but I have at least seen them trigger once or twice during a long stresstest run. v2: Add extra documentation for register fields Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: checkpatch.pl error fixes for rt2800.hMark Einon2010-11-15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | rt2800.h:1511: ERROR: space prohibited after that open parenthesis '(' rt2800.h:1511: ERROR: space prohibited before that close parenthesis ')' rt2800.h:1513: ERROR: space prohibited after that open parenthesis '(' rt2800.h:1513: ERROR: space prohibited before that close parenthesis ')' rt2800.h:1515: ERROR: space prohibited after that open parenthesis '(' rt2800.h:1515: ERROR: space prohibited before that close parenthesis ')' rt2800.h:1517: ERROR: space prohibited after that open parenthesis '(' rt2800.h:1517: ERROR: space prohibited before that close parenthesis ')' rt2800.h:1519: ERROR: space prohibited after that open parenthesis '(' rt2800.h:1519: ERROR: space prohibited before that close parenthesis ')' rt2800.h:1521: ERROR: space prohibited after that open parenthesis '(' rt2800.h:1521: ERROR: space prohibited before that close parenthesis ')' rt2800.h:1661: ERROR: space prohibited after that open parenthesis '(' rt2800.h:1661: ERROR: space prohibited before that close parenthesis ')' rt2800.h:1662: ERROR: space prohibited after that open parenthesis '(' rt2800.h:1662: ERROR: space prohibited before that close parenthesis ')' rt2800.h:1663: ERROR: space prohibited before that close parenthesis ')' rt2800.h:2013: ERROR: space prohibited after that open parenthesis '(' rt2800.h:2013: ERROR: space prohibited before that close parenthesis ')' rt2800.h:2014: ERROR: space prohibited after that open parenthesis '(' rt2800.h:2014: ERROR: space prohibited before that close parenthesis ')' Signed-off-by: Mark Einon <mark.einon@gmail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add TXOP_CTRL_CFG register definitionHelmut Schaa2010-11-15
| | | | | | | | | | | Remove the magic value initialisation of the TXOP_CTRL_CFG register by defining its fields and using them during intialisation. The field RESERVED_TRUN_EN is referred to as reserved, however it is set to 1 by the legacy drivers. Hence, do the same. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Update comment about the AMPDU flag in the TXWIHelmut Schaa2010-10-05
| | | | | | | | | | | | During testing with AMPDUs it turned out that the rt2800 hw will aggregate consecutive frames with the same RA and TID when the first frame in a possible aggregate has set AMPDU=1 in the TXWI. If a following frame has set AMPDU=0 in its TXWI it might sill end up in the aggregate of the previous frame. Update the comment accordingly. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Improve TX status entry validationIvo van Doorn2010-10-05
| | | | | | | | | | | | | | | | | | | | | | | | | The TX_STA_FIFO contains some information for identifying a outgoing frame, however matching by WCID and ACK status is not sufficient to 100% identify the macthing queue_entry structure (containing the SKB buffer) which belongs to the status report. Within TX_STA_FIFO we have a 4-bit field named PACKETID, which is currently used to encode the queue id. The queue ID is however limited to values from 0 to 3, which means 2 bits are sufficient to encode the value. With the remaining 2 bits we can encode a partial queue_entry index number. The value of PACKETID is not allowed to become 0, with the queue ID ranging from 0 to 3, at least one of the bits for the entry identification must be 1. That leaves us with 3 possible values we can still encode in the bits. Altough this doesn't allow 100% accurate matching of the TX_STA_FIFO queue to a queue_entry structure, it at least improves the accuracy. This allows us to better detect if we have missed the TX_STA_FIFO report, which in turn reduces the number of watchdog warnings regarding the TX status timeout. Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: add field definitions for the TBTT_SYNC_CFG registerHelmut Schaa2010-10-05
| | | | | | Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Add register definition for busy time on secondary channelHelmut Schaa2010-10-05
| | | | | | | | | | Add the register definition CH_BUSY_STA_SEC for reading the busy time on the secondary channel in HT40 mode. Also update the comments about channel busy/idle time registers to express the used unit. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Allow tx duplication for legacy rates in HT40 modeHelmut Schaa2010-10-05
| | | | | | | | | | | Make use of the IEEE80211_TX_RC_DUP_DATA flag to duplicate a transmission with legacy rates to both 20Mhz channels if set. Also update the related comment in rt2800.h to describe the behavior of the BW_40 flag for legacy rates. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Don't overwrite beacon buffers in pairwise key setupHelmut Schaa2010-10-05
| | | | | | | | | | | | rt2800 devices use parts of the pariwise key table to store the beacon frames for beacon 6 and 7. To not overwrite the beacon frame buffers limit the number of entries we store in the pairwise key table to 222. Also add some descriptive comments about this shared memory usage. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Initialize AMPDU_BA_WINSIZE registerHelmut Schaa2010-09-14
| | | | | | | | | Since we're not using the AMPDU_BA_WINSIZE register to force the BlockAck window size (we specify it in every TXWI) we should initialize it to 0. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Update rt2800 comments regarding AMPDU and PACKET_ID in TXWIHelmut Schaa2010-08-31
| | | | | | Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Fix max TX power settingsIvo van Doorn2010-08-25
| | | | | | | | | | | | | | | | | | | | | | During initialization each driver reads the default TX power for each individual channel. However mac80211 only accepts the maximum value (which is also handled as default value). As a result, the TX power of the device was being limited to the default value, which is often quite low compared to the real maximum acceptable value. This patch allows each driver to set the maximum value on a per-channel basis which is forwarded to mac80211. The default value will be preserved for now, in case we want to update mac80211 to differentiate between the maximum and default txpower. This fixes bug complaining about limited TX power values like: https://bugzilla.kernel.org/show_bug.cgi?id=16358 Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* rt2x00: Update comments regarding TXWI and TX_STA_FIFOHelmut Schaa2010-08-16
| | | | | | | | | | Add some comments about the TXWI fields and the TX_STA_FIFO register. Especially describe the relationship between the TXWI field PACKETID and the PID field in the TX_STA_FIFO register. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Merge branch 'master' of ↵John W. Linville2010-07-13
|\ | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem Conflicts: drivers/net/wireless/wl12xx/wl1271_cmd.h
| * rt2x00: Use pretbtt irq for fetching beacons on rt2800pciHelmut Schaa2010-07-12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Updating the beacon on pre tbtt instead of beacondone allows much lower latency in regard to TIM updates. Hence, use the pre tbtt interrupt for updating the beacon in rt2800pci (older devices don't provide a pre tbtt interrupt). Also, add a new driver flag to indicate if a driver has pre tbtt support or not and implement the according behavior in rt2x00lib. Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-10-20 04:43:36 -0400