| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds support for a new copper device for 82599, device id 0x151c.
This 82599 10GBase-T device uses the PHY's internal temperature sensor
to guard against over-temp conditions. In this scenario the PHY will be
put in a low power mode and link will no longer be able to transmit or
receive any data. When this occurs, the over-temp interrupt is latched
and driver logs this error message. A HW reset or power cycle is
required to clear this status.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
| |
This patch adds support of active DA cables. This is
renaming and adding some PHY type enumerations.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
| |
Includes one minor indentation fix to placate checkpatch.
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
| |
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Several small fixes around negative test case of the insertion of a
IXGBE_ERR_NOT_SUPPORTED module.
- mdio45_probe call was always failing due to mdio.prtad not being
set. The function set to mdio.mdio_read was still working as we just
happen to always be at prtad == 0. This will allow us to set the phy_id
and phy.type correctly now.
- There was timing issue with i2c calls when initiated from a tasklet.
A small delay was added to allow the electrical oscillation to calm down.
- Logic change in ixgbe_sfp_task that allows NOT_SUPPORTED condition
to be recognized.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
82599 supports multispeed fiber optical modules (10Gbps/1Gbps). Some
scenarios can cause the autotry mechanism to not negotiate link properly.
What needs to happen is the driver must flap the Tx laser to induce an Rx
Loss of Signal on the link partner. This will restart the autotry
mechanism to get link into a known state. The software definable pin (SDP)
3 on the 0x10fb NIC is wired to cause a Tx LOS event, which triggers the
Rx LOS we require.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
If we loaded the driver with out a SFP module plugged in it would
leave it in a state that make it later unable to link when a module
was plugged in. This patch corrects that by:
ixgbe_probe() - moving the check for IXGBE_ERR_SFP_NOT_PRESENT from
after get_invariants() to after reset_hw() as now reset_hw() is
where this condition will be indentified.
ixgbe_reset_hw_82598() - Enable this function to now return
IXGBE_ERR_SFP_NOT_PRESENT.
ixgbe_identify_sfp_module_generic() - This where the lack of SFP
module is detected. Modifications are added to allow a different
return value for modules that just haven't been plugged in yet.
Other functions were updated to allow correct logging.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
The SFF specification for Direct Attach cable detection has now been
ratified. Previously, DA cable detect was looking at the Twinaxial bit in
byte 9 of the SFP+ EEPROM. The spec now defines active and passive DA
cables in byte 8 of the SFP+ EEPROM. This patch changes the cable
detection for both 82598 and 82599 SFP+ adapters to conform to the new
spec.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
| |
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
82598 and 82599 do not support SFP 1G modules. Instead of allowing the
driver to load, but never get link, rejecting the module and displaying
a useful message is more preferrable. The framework for displaying the
failure message already exists, now we just need to detect and reject the
SFP modules.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Not all physical connection types are being correctly identified. This
fixes that issue, and cleans up the logic to make it more maintainable.
Also clean up the code for device capabilities from the EEPROM to support
multiple SKUs of the same hardware.
Bump the version to reflect all the updates since the 82599 merge.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
| |
This patch does two things:
1) On 82599, the PHY is emedded in the MAC. On 82598, the SFP+ NIC has an external PHY. The reset in the SFP+ setup patch for 82598 is unnecessary on 82599, and adds extra dead time to device initialization. This removes that PHY reset for 82599 only.
2) On 82599, the SFP+ modules are multispeed fiber modules (10G/1G). We need to make sure to identify them properly for the remaining init sections to properly set them up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
This patch adds the hardware initialization code specific to 82599. This
is similar to the 82598 hardware initialization code. It also includes all
changes to the existing hardware init code to support 82599.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
| |
New year, new copyright date ranges. Also bump the driver version
number to reflect many of the recent changes.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds support for SFP+ PHY in the following device ID's (10DB,
10F1, 10E1). These SFP+ PHY's are accessed via an I2C interface so the
patch also includes functions to support this.
Another feature of note is that the PHY is pluggable and some
rearchitecting was needed to support this.
Signed-off-by: Donald Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |
|
|
|
|
|
|
|
|
| |
Intel is currently shipping support for adapters with a phy
that does 10GBase-T (copper), which is 10 Gigabit ethernet
over standard Category 6 cabling.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
| |
|
|
|
|
|
|
|
|
| |
This patch cleans up a bit of whitespace issues with the driver, updates
the copyright information, and bumps the version number up.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
This is a massive update that includes infrastructure for further patches
where we will add support for more phy types and eeprom types.
This code is shared as much as possible with other drivers, so the code may
seem a little obtuse at times but wherever possible we keep to the linux
style and methods.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
|
This patch adds support for the Intel 82598 PCI-Express 10GbE
chipset. Devices will be available on the market soon.
This version of the driver is largely the same as the last release:
* Driver uses a single RX and single TX queue, each using 1 MSI-X
irq vector.
* Driver runs in NAPI mode only
* Driver is largely multiqueue-ready (TM)
Changes since 20070803:
* removed wrappers for hardware functions
* incorporated e1000e-style HW api reorganization code
* sparse/checkpatch cleanups, namespace cleanups
* driver prints out extra debugging information at load time
identifying adapter board number, mac, phy types
* removed ixgbe_api.c, ixgbe_api.h, ixgbe_osdep.h
* driver update to 1.1.18
* removed ixgbe.txt which contained no useful info anymore
[ Integrated napi_struct changes from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Ayyappan Veeraiyan <ayyappan.veeraiyan@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
