6 files changed, 19 insertions, 11 deletions

diff --git a/Documentation/arm/mem_alignment b/Documentation/arm/mem_alignment
index d145ccca169..c7c7a114c78 100644
--- a/Documentation/arm/mem_alignment
+++ b/Documentation/arm/mem_alignment
@@ -24,7 +24,7 @@ real bad - it changes the behaviour of all unaligned instructions in user
 space, and might cause programs to fail unexpectedly.
 
 To change the alignment trap behavior, simply echo a number into
-/proc/sys/debug/alignment.  The number is made up from various bits:
+/proc/cpu/alignment.  The number is made up from various bits:
 
 bit             behavior when set
 ---             -----------------
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 2919a2e9193..edab81c1318 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -89,6 +89,7 @@ parameter is applicable:
         SPARC   Sparc architecture is enabled.
         SWSUSP  Software suspend (hibernation) is enabled.
         SUSPEND System suspend states are enabled.
+        FTRACE  Function tracing enabled.
         TS      Appropriate touchscreen support is enabled.
         USB     USB support is enabled.
         USBHID  USB Human Interface Device support is enabled.
@@ -2173,6 +2174,9 @@ and is between 256 and 4096 characters. It is defined in the file
         st=             [HW,SCSI] SCSI tape parameters (buffers, etc.)
                         See Documentation/scsi/st.txt.
 
+        stacktrace      [FTRACE]
+                        Enabled the stack tracer on boot up.
+
         sti=            [PARISC,HW]
                         Format: <num>
                         Set the STI (builtin display/keyboard on the HP-PARISC
diff --git a/Documentation/local_ops.txt b/Documentation/local_ops.txt
index f4f8b1c6c8b..23045b8b50f 100644
--- a/Documentation/local_ops.txt
+++ b/Documentation/local_ops.txt
@@ -149,7 +149,7 @@ static void do_test_timer(unsigned long data)
         int cpu;
 
         /* Increment the counters */
-        on_each_cpu(test_each, NULL, 0, 1);
+        on_each_cpu(test_each, NULL, 1);
         /* Read all the counters */
         printk("Counters read from CPU %d\n", smp_processor_id());
         for_each_online_cpu(cpu) {
diff --git a/Documentation/usb/gadget_serial.txt b/Documentation/usb/gadget_serial.txt
index 9b22bd14c34..eac7df94d8e 100644
--- a/Documentation/usb/gadget_serial.txt
+++ b/Documentation/usb/gadget_serial.txt
@@ -114,11 +114,11 @@ modules.
 Then you must load the gadget serial driver.  To load it as an
 ACM device (recommended for interoperability), do this:
 
-  modprobe g_serial use_acm=1
+  modprobe g_serial
 
 To load it as a vendor specific bulk in/out device, do this:
 
-  modprobe g_serial
+  modprobe g_serial use_acm=0
 
 This will also automatically load the underlying gadget peripheral
 controller driver.  This must be done each time you reboot the gadget
diff --git a/Documentation/usb/proc_usb_info.txt b/Documentation/usb/proc_usb_info.txt
index 077e9032d0c..fafcd472326 100644
--- a/Documentation/usb/proc_usb_info.txt
+++ b/Documentation/usb/proc_usb_info.txt
@@ -49,8 +49,10 @@ it and 002/048 sometime later.
 
 These files can be read as binary data.  The binary data consists
 of first the device descriptor, then the descriptors for each
-configuration of the device.  That information is also shown in
-text form by the /proc/bus/usb/devices file, described later.
+configuration of the device.  Multi-byte fields in the device and
+configuration descriptors, but not other descriptors, are converted
+to host endianness by the kernel.  This information is also shown
+in text form by the /proc/bus/usb/devices file, described later.
 
 These files may also be used to write user-level drivers for the USB
 devices.  You would open the /proc/bus/usb/BBB/DDD file read/write,
diff --git a/Documentation/usb/usbmon.txt b/Documentation/usb/usbmon.txt
index 2917ce4ffdc..270481906dc 100644
--- a/Documentation/usb/usbmon.txt
+++ b/Documentation/usb/usbmon.txt
@@ -34,11 +34,12 @@ if usbmon is built into the kernel.
 Verify that bus sockets are present.
 
 # ls /sys/kernel/debug/usbmon
-0s  0t  0u  1s  1t  1u  2s  2t  2u  3s  3t  3u  4s  4t  4u
+0s  0u  1s  1t  1u  2s  2t  2u  3s  3t  3u  4s  4t  4u
 #
 
-Now you can choose to either use the sockets numbered '0' (to capture packets on
-all buses), and skip to step #3, or find the bus used by your device with step #2.
+Now you can choose to either use the socket '0u' (to capture packets on all
+buses), and skip to step #3, or find the bus used by your device with step #2.
+This allows to filter away annoying devices that talk continuously.
 
 2. Find which bus connects to the desired device
 
@@ -99,8 +100,9 @@ on the event type, but there is a set of words, common for all types.
 
 Here is the list of words, from left to right:
 
-- URB Tag. This is used to identify URBs is normally a kernel mode address
- of the URB structure in hexadecimal.
+- URB Tag. This is used to identify URBs, and is normally an in-kernel address
+  of the URB structure in hexadecimal, but can be a sequence number or any
+  other unique string, within reason.
 
 - Timestamp in microseconds, a decimal number. The timestamp's resolution
   depends on available clock, and so it can be much worse than a microsecond