Pull IOMMU updates from Joerg Roedel:
 "A few new features this merge-window.  The most important one is
  probably, that dma-debug now warns if a dma-handle is not checked with
  dma_mapping_error by the device driver.  This requires minor changes
  to some architectures which make use of dma-debug.  Most of these
  changes have the respective Acks by the Arch-Maintainers.

  Besides that there are updates to the AMD IOMMU driver for refactor
  the IOMMU-Groups support and to make sure it does not trigger a
  hardware erratum.

  The OMAP changes (for which I pulled in a branch from Tony Lindgren's
  tree) have a conflict in linux-next with the arm-soc tree.  The
  conflict is in the file arch/arm/mach-omap2/clock44xx_data.c which is
  deleted in the arm-soc tree.  It is safe to delete the file too so
  solve the conflict.  Similar changes are done in the arm-soc tree in
  the common clock framework migration.  A missing hunk from the patch
  in the IOMMU tree will be submitted as a seperate patch when the
  merge-window is closed."

* tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (29 commits)
  ARM: dma-mapping: support debug_dma_mapping_error
  ARM: OMAP4: hwmod data: ipu and dsp to use parent clocks instead of leaf clocks
  iommu/omap: Adapt to runtime pm
  iommu/omap: Migrate to hwmod framework
  iommu/omap: Keep mmu enabled when requested
  iommu/omap: Remove redundant clock handling on ISR
  iommu/amd: Remove obsolete comment
  iommu/amd: Don't use 512GB pages
  iommu/tegra: smmu: Move bus_set_iommu after probe for multi arch
  iommu/tegra: gart: Move bus_set_iommu after probe for multi arch
  iommu/tegra: smmu: Remove unnecessary PTC/TLB flush all
  tile: dma_debug: add debug_dma_mapping_error support
  sh: dma_debug: add debug_dma_mapping_error support
  powerpc: dma_debug: add debug_dma_mapping_error support
  mips: dma_debug: add debug_dma_mapping_error support
  microblaze: dma-mapping: support debug_dma_mapping_error
  ia64: dma_debug: add debug_dma_mapping_error support
  c6x: dma_debug: add debug_dma_mapping_error support
  ARM64: dma_debug: add debug_dma_mapping_error support
  intel-iommu: Prevent devices with RMRRs from being placed into SI Domain
  ...

Pull ARM SoC fixes from Olof Johansson:
 "This is a batch of fixes for arm-soc platforms, most of it is for OMAP
  but there are others too (i.MX, Tegra, ep93xx).  Fixes warnings, some
  broken platforms and drivers, etc.  A bit all over the map really."

There was some concern about commit 68136b10 ("RM: sunxi: Change device
tree naming scheme for sunxi"), but Tony says:
 "Looks like that's trivial to fix as needed, no need to rebuild the
  branch to fix that AFAIK.

  The fix can be done once Olof is available online again.

  Linus, I suggest that you go ahead and pull this if there are no other
  issues with this branch."

* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
  ARM: sunxi: Change device tree naming scheme for sunxi
  ARM: ux500: fix missing include
  ARM: u300: delete custom pin hog code
  ARM: davinci: fix build break due to missing include
  ARM: exynos: Fix warning due to missing 'inline' in stub
  ARM: imx: Move platform-mx2-emma to arch/arm/mach-imx/devices
  ARM i.MX51 clock: Fix regression since enabling MIPI/HSP clocks
  ARM: dts: mx27: Fix the AIPI bus for FEC
  ARM: OMAP2+: common: remove use of vram
  ARM: OMAP3/4: cpuidle: fix sparse and checkpatch warnings
  ARM: OMAP4: clock data: DPLLs are missing bypass clocks in their parent lists
  ARM: OMAP4: clock data: div_iva_hs_clk is a power-of-two divider
  ARM: OMAP4: Fix EMU clock domain always on
  ARM: OMAP4460: Workaround ABE DPLL failing to turn-on
  ARM: OMAP4: Enhance support for DPLLs with 4X multiplier
  ARM: OMAP4: Add function table for non-M4X dplls
  ARM: OMAP4: Update timer clock aliases
  ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
  ARM: dts: Add build target for omap4-panda-a4
  ARM: dts: OMAP2420: Correct H4 board memory size
  ...

Pull MTD updates from David Woodhouse:
 - Various cleanups especially in NAND tests
 - Add support for NAND flash on BCMA bus
 - DT support for sh_flctl and denali NAND drivers
 - Kill obsolete/superceded drivers (fortunet, nomadik_nand)
 - Fix JFFS2 locking bug in ENOMEM failure path
 - New SPI flash chips, as usual
 - Support writing in 'reliable mode' for DiskOnChip G4
 - Debugfs support in nandsim

* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
  mtd: nand: typo in nand_id_has_period() comments
  mtd: nand/gpio: use io{read,write}*_rep accessors
  mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
  mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
  mtd: nand/docg4: fix and improve read of factory bbt
  mtd: nand/docg4: reserve bb marker area in ecclayout
  mtd: nand/docg4: add support for writing in reliable mode
  mtd: mxc_nand: reorder part_probes to let cmdline override other sources
  mtd: mxc_nand: fix unbalanced clk_disable() in error path
  mtd: nandsim: Introduce debugfs infrastructure
  mtd: physmap_of: error checking to prevent a NULL pointer dereference
  mtg: docg3: potential divide by zero in doc_write_oob()
  mtd: bcm47xxnflash: writing support
  mtd: tests/read: initialize buffer for whole next page
  mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
  mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
  mtd: nand: onfi need to be probed in 8 bits mode
  mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
  mtd: nand: print flash size during detection
  mted: nand_wait_ready timeout fix
  ...

Pull i2c-embedded changes from Wolfram Sang:
 - CBUS driver (an I2C variant)
 - continued rework of the omap driver
 - s3c2410 gets lots of fixes and gains pinctrl support
 - at91 gains DMA support
 - the GPIO muxer gains devicetree probing
 - typical fixes and additions all over

* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
  i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
  i2c: at91: add dma support
  i2c: at91: change struct members indentation
  i2c: at91: fix compilation warning
  i2c: mxs: Do not disable the I2C SMBus quick mode
  i2c: mxs: Handle i2c DMA failure properly
  i2c: s3c2410: Remove recently introduced performance overheads
  i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
  i2c: s3c2410: Add fix for i2c suspend/resume
  i2c: s3c2410: Fix code to free gpios
  i2c: i2c-cbus-gpio: introduce driver
  i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
  i2c: ocores: Add irq support for sparc
  i2c: omap: Move the remove constraint
  ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
  i2c: s3c2410: do not special case HDMIPHY stuck bus detection
  i2c: s3c2410: use exponential back off while polling for bus idle
  i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
  i2c: s3c2410: grab adapter lock while changing i2c clock
  i2c: s3c2410: Add support for pinctrl
  ...

From Tony Lindgren:

These patches fixes a build error caused by a merge
conflict with the fb code, few timer warnings, and longer
term regressions for tfp410 and omap h4 ethernet. Also
included is a GPIO mode fix for the legacy mux code.

* tag 'omap-for-v3.8/fixes-for-merge-window-v4-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: common: remove use of vram
  ARM: OMAP: Move plat/omap-serial.h to include/linux/platform_data/serial-omap.h
  ARM: dts: Add build target for omap4-panda-a4
  ARM: dts: OMAP2420: Correct H4 board memory size
  mfd: omap-usb-host: get rid of cpu_is_omap..() macros
  ARM: OMAP: Remove debug-devices.c
  ARM: OMAP2420: Fix ethernet support for OMAP2420 H4
  OMAP2+: mux: Fixed gpio mux mode analysis
  OMAP: board-files: fix i2c_bus for tfp410
  ARM: OMAP2+: Fix sparse warnings in timer.c
  ARM: AM335x: Fix warning in timer.c
  ARM: OMAP2+: Fix realtime_counter_init warning in timer.c

The LP855x family devices support the PWM input for the backlight control.
 Period of the PWM is configurable in the platform side.  Platform
specific functions are unnecessary anymore because generic PWM functions
are used inside the driver.

(PWM input mode)
To set the brightness, new lp855x_pwm_ctrl() is used.
If a PWM device is not allocated, devm_pwm_get() is called.
The PWM consumer name is from the chip name such as 'lp8550' and 'lp8556'.
To get the brightness value, no additional handling is required.
Just the value of 'props.brightness' is returned.

If the PWM driver is not ready while initializing the LP855x driver, it's
OK.  The PWM device can be retrieved later, when the brightness value is
changed.

Documentation is updated with an example.

[akpm@linux-foundation.org: coding-style simplification, per Thierry]
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <bryan.wu@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull MFS update from Samuel Ortiz:
 "This is the MFD patch set for the 3.8 merge window.

  We have several new drivers, most of the time coming with their sub
  devices drivers:

   - Austria Microsystem's AS3711
   - Nano River's viperboard
   - TI's TPS80031, AM335x TS/ADC,
   - Realtek's MMC/memstick card reader
   - Nokia's retu

  We also got some notable cleanups and improvements:

   - tps6586x got converted to IRQ domains.
   - tps65910 and tps65090 moved to the regmap IRQ API.
   - STMPE is now Device Tree aware.
   - A general twl6040 and twl-core cleanup, with moves to the regmap
     I/O and IRQ APIs and a conversion to the recently added PWM
     framework.
   - sta2x11 gained regmap support.

  Then the rest is mostly tiny cleanups and fixes, among which we have
  Mark's wm5xxx and wm8xxx patchset."

Far amount of annoying but largely trivial conflicts.  Many due to
__devinit/exit removal, others due to one or two of the new drivers also
having come in through another tree.

* tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits)
  mfd: tps6507x: Convert to devm_kzalloc
  mfd: stmpe: Update DT support for stmpe driver
  mfd: wm5102: Add readback of DSP status 3 register
  mfd: arizona: Log if we fail to create the primary IRQ domain
  mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ
  mfd: tps80031: Add terminating entry for tps80031_id_table
  mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask()
  mfd: wm5102: Add tuning for revision B
  mfd: arizona: Defer patch initialistation until after first device boot
  mfd: tps65910: Fix wrong ack_base register
  mfd: tps65910: Remove unused data
  mfd: stmpe: Get rid of irq_invert_polarity
  mfd: ab8500-core: Fix invalid free of devm_ allocated data
  mfd: wm5102: Mark DSP memory regions as volatile
  mfd: wm5102: Correct default for LDO1_CONTROL_2
  mfd: arizona: Register haptics devices
  mfd: wm8994: Make current device behaviour the default
  mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ
  mfd: Fix stmpe.c build when OF is not enabled
  mfd: jz4740-adc: Use devm_kzalloc
  ...