From c95522a7cc9461fd5b2c18cb72b66b46680bffa7 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 3 Dec 2009 17:25:57 +0100 Subject: cy82c693: remove no longer needed debugging code Signed-off-by: Bartlomiej Zolnierkiewicz --- drivers/ide/cy82c693.c | 27 --------------------------- 1 file changed, 27 deletions(-) (limited to 'drivers/ide') diff --git a/drivers/ide/cy82c693.c b/drivers/ide/cy82c693.c index 74fc5401f40..d6e2cbbc53a 100644 --- a/drivers/ide/cy82c693.c +++ b/drivers/ide/cy82c693.c @@ -50,11 +50,6 @@ #define DRV_NAME "cy82c693" -/* - * The following are used to debug the driver. - */ -#define CY82C693_DEBUG_INFO 0 - /* * NOTE: the value for busmaster timeout is tricky and I got it by * trial and error! By using a to low value will cause DMA timeouts @@ -176,11 +171,6 @@ static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode) outb(index, CY82_INDEX_PORT); outb(data, CY82_DATA_PORT); -#if CY82C693_DEBUG_INFO - printk(KERN_INFO "%s (ch=%d, dev=%d): set DMA mode to %d (single=%d)\n", - drive->name, hwif->channel, drive->dn & 1, mode & 3, single); -#endif /* CY82C693_DEBUG_INFO */ - /* * note: below we set the value for Bus Master IDE TimeOut Register * I'm not absolutly sure what this does, but it solved my problem @@ -194,11 +184,6 @@ static void cy82c693_set_dma_mode(ide_drive_t *drive, const u8 mode) data = BUSMASTER_TIMEOUT; outb(CY82_INDEX_TIMEOUT, CY82_INDEX_PORT); outb(data, CY82_DATA_PORT); - -#if CY82C693_DEBUG_INFO - printk(KERN_INFO "%s: Set IDE Bus Master TimeOut Register to 0x%X\n", - drive->name, data); -#endif /* CY82C693_DEBUG_INFO */ } static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio) @@ -239,8 +224,6 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio) pci_write_config_byte(dev, CY82_IDE_MASTER_IOR, pclk.time_16r); pci_write_config_byte(dev, CY82_IDE_MASTER_IOW, pclk.time_16w); pci_write_config_byte(dev, CY82_IDE_MASTER_8BIT, pclk.time_8); - - addrCtrl &= 0xF; } else { /* * set slave drive @@ -257,17 +240,7 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio) pci_write_config_byte(dev, CY82_IDE_SLAVE_IOR, pclk.time_16r); pci_write_config_byte(dev, CY82_IDE_SLAVE_IOW, pclk.time_16w); pci_write_config_byte(dev, CY82_IDE_SLAVE_8BIT, pclk.time_8); - - addrCtrl >>= 4; - addrCtrl &= 0xF; } - -#if CY82C693_DEBUG_INFO - printk(KERN_INFO "%s (ch=%d, dev=%d): set PIO timing to " - "(addr=0x%X, ior=0x%X, iow=0x%X, 8bit=0x%X)\n", - drive->name, hwif->channel, drive->dn & 1, - addrCtrl, pclk.time_16r, pclk.time_16w, pclk.time_8); -#endif /* CY82C693_DEBUG_INFO */ } static void __devinit init_iops_cy82c693(ide_hwif_t *hwif) -- cgit v1.2.2