aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/e1000e/netdev.c
Commit message (Collapse)AuthorAge
...
* | e1000e: store EEPROM version number to prevent unnecessary NVM readsBruce Allan2008-11-21
| | | | | | | | | | | | | | | | | | | | Rather than reading the NVM to get the EEPROM version number everytime the ethool get_drvinfo function is called, read it once during probe and save it for future reference. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: sync change flow control variables with ixgbeBruce Allan2008-11-21
| | | | | | | | | | | | | | | | | | Sync flow control variables and usage model with that found in the ixgbe driver. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: link up/down messages must follow a specific formatBruce Allan2008-11-21
| | | | | | | | | | | | | | | | | | The system log messages created on a link status change need to follow a specific format to work with tools some customers use. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: ESB2 config after link upBruce Allan2008-11-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | On ESB2, the MAC-to-PHY (Kumeran) interface must be configured after link is up before any traffic is sent; a new PHY operations function pointer is provided for this. To facilitate read/write of the Kumeran registers without blocking PHY register writes, the driver/firmware synchronization method which previously used a hardware semaphore for both PHY and Kumeran register accesses is now split. New Kumeran register read/write functions utilize this new synchronization method. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: check return of pci_save_stateBruce Allan2008-11-21
| | | | | | | | | | | | | | | | Check return of pci_save_state and error out accordingly. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: disable correctable errors for quad ports while going to D3Alexander Duyck2008-11-21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | There has been an issue seen with the pci-e quad port adapters that will cause them to generate a pci-e correctable error on some system while transitioning to D3. Since no action is needed on this correctable error the simplest solution is to mask off the reporting of correctable errors. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | netdev: add more functions to netdevice opsStephen Hemminger2008-11-20
| | | | | | | | | | | | | | | | | | | | | | | | This patch moves neigh_setup and hard_start_xmit into the network device ops structure. For bisection, fix all the previously converted drivers as well. Bonding driver took the biggest hit on this. Added a prefetch of the hard_start_xmit in the fast path to try and reduce any impact this would have. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | e1000e: convert to net_device_opsStephen Hemminger2008-11-20
| | | | | | | | | | | | Convert e1000e to network device ops. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
* | Merge branch 'master' of ↵David S. Miller2008-11-19
|\| | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/isdn/i4l/isdn_net.c fs/cifs/connect.c
| * e1000e: fix IPMI trafficJeff Kirsher2008-11-16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some users reported that they have machines with BMCs enabled that cannot receive IPMI traffic after e1000e is loaded. http://marc.info/?l=e1000-devel&m=121909039127414&w=2 http://marc.info/?l=e1000-devel&m=121365543823387&w=2 This fixes the issue if they load with the new parameter = 0 by disabling crc stripping, but leaves the performance feature on for most users. Based on work done by Hong Zhang. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * e1000e: fix warn_on reload after phy_id errorJeff Kirsher2008-11-16
| | | | | | | | | | | | | | | | | | | | If the driver fails to initialize the first time due to the failure in the phy_id check the kernel triggers a warn_on on the second try to load the driver because the driver did not free the msi/x resources in the first load because of the previous failure in phy_id check. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * e1000e: Use device_set_wakeup_enable\"Rafael J. Wysocki\2008-11-16
| | | | | | | | | | | | | | | | | | | | | | | | Since dev->power.should_wakeup bit is used by the PCI core to decide whether the device should wake up the system from sleep states, set/unset this bit whenever WOL is enabled/disabled using e1000_set_wol(). Accordingly, use device_can_wakeup() for checking if wake-up is supported by the device. Signed-off-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | netdevice: safe convert to netdev_priv() #part-2Wang Chen2008-11-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have some reasons to kill netdev->priv: 1. netdev->priv is equal to netdev_priv(). 2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously netdev_priv() is more flexible than netdev->priv. But we cann't kill netdev->priv, because so many drivers reference to it directly. This patch is a safe convert for netdev->priv to netdev_priv(netdev). Since all of the netdev->priv is only for read. But it is too big to be sent in one mail. I split it to 4 parts and make every part smaller than 100,000 bytes, which is max size allowed by vger. Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | drivers/net: Kill now superfluous ->last_rx stores.David S. Miller2008-11-04
| | | | | | | | | | | | | | | | | | | | | | | | | | The generic packet receive code takes care of setting netdev->last_rx when necessary, for the sake of the bonding ARP monitor. Drivers need not do it any more. Some cases had to be skipped over because the drivers were making use of the ->last_rx value themselves. Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: convert more to %pMJohannes Berg2008-10-27
|/ | | | | | | | | A number of places still use %02x:...:%02x because it's in debug statements or for no real reason. Make a few of them use %pM. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
* e1000e: don't generate bad checksums for tcp packets with 0 csumDave Graham2008-10-09
| | | | | | | | | | | | | | When offloading transmit checksums only, the driver was not correctly configuring the hardware to handle the case of a zero checksum. For UDP the correct behavior is to leave it alone, but for tcp the checksum must be changed from 0x0000 to 0xFFFF. The hardware takes care of this case but only if it is told the packet is tcp. Signed-off-by: Dave Graham <david.graham@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2008-10-08
|\ | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/e1000e/ich8lan.c drivers/net/e1000e/netdev.c
| * e1000e: update version from k4 to k6Jesse Brandeburg2008-10-02
| | | | | | | | | | Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * e1000e: drop stats lockJesse Brandeburg2008-10-02
| | | | | | | | | | | | | | | | | | | | | | | | the stats lock is left over from e1000, e1000e no longer has the adjust tbi stats function that required the addition of the stats lock to begin with. adding a mutex to acquire_swflag helped catch this one too. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * e1000e: remove phy read from inside spinlockJesse Brandeburg2008-10-02
| | | | | | | | | | | | | | | | | | | | | | thanks to tglx, we're finding some interesting reentrancy issues. this patch removes the phy read from inside a spinlock, paving the way for removing the spinlock completely. The phy read was only feeding a statistic that wasn't used. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * e1000e: do not ever sleep in interrupt contextJesse Brandeburg2008-10-02
| | | | | | | | | | | | | | | | | | | | | | | | | | e1000e was apparently calling two functions that attempted to reserve the SWFLAG bit for exclusive (to hardware and firmware) access to the PHY and NVM (aka eeprom). These accesses could possibly call msleep to wait for the resource which is not allowed from interrupt context. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
| * e1000e: write protect ICHx NVM to prevent malicious write/eraseBruce Allan2008-10-01
| | | | | | | | | | | | | | | | | | | | | | | | Set the hardware to ignore all write/erase cycles to the GbE region in the ICHx NVM. This feature can be disabled by the WriteProtectNVM module parameter (enabled by default) only after a hardware reset, but the machine must be power cycled before trying to enable writes. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> CC: arjan@linux.intel.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | e1000e: avoid duplicated output of device name in kernel warningFrans Pop2008-09-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With 2.6.27-rc3 I noticed the following messages in my boot log: 0000:01:00.0: 0000:01:00.0: Warning: detected DSPD enabled in EEPROM 0000:01:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:16:76:04:ff:09 The second seems correct, but the first has a silly repetition of the PCI device before the actual message. The message originates from e1000_eeprom_checks in e1000e/netdev.c. With this patch below the first message becomes e1000e 0000:01:00.0: Warning: detected DSPD enabled in EEPROM which makes it similar to directly preceding messages. Use dev_warn instead of e_warn in e1000_eeprom_checks() as the interface name has not yet been assigned at that point. [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Frans Pop <elendil@planet.nl> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | e1000e: add support for new 82574L partBruce Allan2008-09-03
| | | | | | | | | | | | | | | | | | This new part has the same feature set as previous parts with the addition of MSI-X support. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | e1000e: add support for 82567LM-3 and 82567LF-3 (ICH10D) partsBruce Allan2008-09-03
| | | | | | | | | | | | | | | | Add support for new LOM devices on the latest generation ICHx platforms. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | e1000e: add support for the 82567LM-4 deviceBruce Allan2008-09-03
|/ | | | | | | | | Enable PCI device ID for a new combination of MAC and PHY already supported in the driver. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: test for unusable MSI supportBruce Allan2008-08-14
| | | | | | | | | | | Some systems do not like 82571/2 use of 16-bit MSI messages and some other systems claim to support MSI, but neither really works. Setup a test MSI handler to detect whether or not MSI is working properly, and if not, fallback to legacy INTx interrupts. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: increase minimum frame size allowedBruce Allan2008-08-14
| | | | | | | | | | Setting an MTU value below 68 was disabling the network connection and would not reconnect until the driver was reloaded. Prevent changing the MTU to anything below 68. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: Increase Tx timeout factor for 10MbpsBruce Allan2008-08-14
| | | | | | | | | Prevent Tx hangs from happening on 10Mb flood ping by increasing the timeout factor. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: Use skb_copy_to_linear_data_offset introduced in 2.6.22Bruce Allan2008-08-14
| | | | | | | | | | The e1000e driver was based on a version of e1000 prior to acme's introduction of skb_copy_to_linear_data_offset, and was submitted after acme went through and coverted all the drivers to use it. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: remove inapplicable test for ioportBruce Allan2008-08-07
| | | | | | | | | | There are currently no devices supported by the e1000e driver which need ioport resources, remove the test for it and all unnecessary code associated with it (struct e1000_adapter elements, local variables, etc.) Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: fix drv load issuesJesse Brandeburg2008-08-07
| | | | | | | | | | | | a few people seem to have problems maintaining gigabit link and it was root caused to an interaction between the managability firmware on the host and the driver, not communicating. The form of communication they use is the drv_load bit. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: perform basic 82573 EEPROM checks for known issuesAuke Kok2008-08-07
| | | | | | | | | | | 82573 EEPROMs have been shipped out with known issues. While most people will never see the issues some people do and we know how to address them. Warn the user if we find one of these EEPROM issues. Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: convert ndev_ printks to something smallerJeff Kirsher2008-08-07
| | | | | | | | | The ndev_* printk's are too lenghty and we don't need to specify the adapter/netdev struct at all, making this a lot more readable. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* dma-mapping: add the device argument to dma_mapping_error()FUJITA Tomonori2008-07-26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER architecture does: This enables us to cleanly fix the Calgary IOMMU issue that some devices are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423). I think that per-device dma_mapping_ops support would be also helpful for KVM people to support PCI passthrough but Andi thinks that this makes it difficult to support the PCI passthrough (see the above thread). So I CC'ed this to KVM camp. Comments are appreciated. A pointer to dma_mapping_ops to struct dev_archdata is added. If the pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's NULL, the system-wide dma_ops pointer is used as before. If it's useful for KVM people, I plan to implement a mechanism to register a hook called when a new pci (or dma capable) device is created (it works with hot plugging). It enables IOMMUs to set up an appropriate dma_mapping_ops per device. The major obstacle is that dma_mapping_error doesn't take a pointer to the device unlike other DMA operations. So x86 can't have dma_mapping_ops per device. Note all the POWER IOMMUs use the same dma_mapping_error function so this is not a problem for POWER but x86 IOMMUs use different dma_mapping_error functions. The first patch adds the device argument to dma_mapping_error. The patch is trivial but large since it touches lots of drivers and dma-mapping.h in all the architecture. This patch: dma_mapping_error() doesn't take a pointer to the device unlike other DMA operations. So we can't have dma_mapping_ops per device. Note that POWER already has dma_mapping_ops per device but all the POWER IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device argument. [akpm@linux-foundation.org: fix sge] [akpm@linux-foundation.org: fix svc_rdma] [akpm@linux-foundation.org: build fix] [akpm@linux-foundation.org: fix bnx2x] [akpm@linux-foundation.org: fix s2io] [akpm@linux-foundation.org: fix pasemi_mac] [akpm@linux-foundation.org: fix sdhci] [akpm@linux-foundation.org: build fix] [akpm@linux-foundation.org: fix sparc] [akpm@linux-foundation.org: fix ibmvscsi] Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Muli Ben-Yehuda <muli@il.ibm.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@elte.hu> Cc: Avi Kivity <avi@qumranet.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* e1000e: fix e1000_netpoll(), remove extraneous e1000_clean_tx_irq() callIngo Molnar2008-07-23
| | | | | | | | | | | | | | | | | | | | | | | | | Evgeniy Polyakov noticed that drivers/net/e1000e/netdev.c:e1000_netpoll() was calling e1000_clean_tx_irq() without taking the TX lock. David Miller suggested to remove the call altogether: since in this callpah there's periodic calls to ->poll() anyway which will do e1000_clean_tx_irq() and will garbage-collect any finished TX ring descriptors. This fix solved the e1000e+netconsole crashes i've been seeing: ============================================================================= BUG skbuff_head_cache: Poison overwritten ----------------------------------------------------------------------------- INFO: 0xf658ae9c-0xf658ae9c. First byte 0x6a instead of 0x6b INFO: Allocated in __alloc_skb+0x2c/0x110 age=0 cpu=0 pid=5098 INFO: Freed in __kfree_skb+0x31/0x80 age=0 cpu=1 pid=4440 INFO: Slab 0xc16cc140 objects=16 used=1 fp=0xf658ae00 flags=0x400000c3 INFO: Object 0xf658ae00 @offset=3584 fp=0xf658af00 Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: David S. Miller <davem@davemloft.net>
* igb/ixgbe/e1000e: resolve tx multiqueue bugJeff Kirsher2008-07-18
| | | | | | | | | | | With the recent changes to tx mutiqueue, igb/ixgbe/e1000e was not calling netif_tx_start_all_queues() before calling netif_tx_wake_all_queues(). This causes an issue during loading of the driver. In addition, updated e1000e to use the updated tx mutliqueue api. Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netdrv intel: always enable VLAN filtering except in promiscous modePatrick McHardy2008-07-16
| | | | | | | | | | | | Currently VLAN filtering is enabled when the first VLAN is added. Obviously before that there's no point in receiving any VLAN packets. Now that we disable VLAN filtering in promiscous mode, we can keep the VLAN filters enabled the remaining time. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netdrv intel: disable VLAN filtering in promiscous modePatrick McHardy2008-07-16
| | | | | | | | | | | | | | | As discussed in this thread: http://www.mail-archive.com/netdev@vger.kernel.org/msg53976.html promiscous mode means to disable *all* filters. Currently only unicast and multicast filtering is disabled. This patch changes all Intel drivers to also disable VLAN filtering. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netdrv: don't truncate VLAN TCI with VLAN strippingPatrick McHardy2008-07-06
| | | | | | | | | The vlan_hwaccel_{rx,receive_skb} functions expect the full TCI field for priority mappings, don't truncate the upper 4 bits. Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'davem-next' of ↵David S. Miller2008-06-29
|\ | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
| * e1000e: make ioport freeTaku Izumi2008-06-28
| | | | | | | | | | | | | | | | | | This patch makes e1000e driver ioport-free. This corrects behavior in probe function so as not to request ioport resources as long as they are not really needed. Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | Merge branch 'master' of ↵David S. Miller2008-06-28
|\ \ | |/ |/| | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/wireless/iwlwifi/iwl4965-base.c
| * e1000e: fix EEH recovery during reset on PPCJeff Kirsher2008-06-27
| | | | | | | | | | | | | | | | | | EEH is not recovering in a reasonable amount of time on PPC during e1000e_down(). Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* | e1000e: allow VLAN devices to use TSO and TCP CSUM offloadJeff Kirsher2008-06-11
|/ | | | | | | | | Using the new interface for propagating device feature flags into VLAN devices, turn on TSO and CSUM offload on VLAN devices. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: use resource_size_t, not unsigned long, for phys addrsBecky Bruce2008-05-22
| | | | | | | | The use of unsigned long causes the driver to fail on 32-bit systems which support 64-bit resources. Signed-off-by: Becky Bruce <becky.bruce@freescale.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: Add support for BM PHYs on ICH9Bruce Allan2008-05-06
| | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the BM PHY, a new PHY model being used on ICH9-based implementations. This new PHY exposes issues in the ICH9 silicon when receiving jumbo frames large enough to use more than a certain part of the Rx FIFO, and this unfortunately breaks packet split jumbo receives. For this reason we re-introduce (for affected adapters only) the jumbo single-skb receive routine back so that people who do wish to use jumbo frames on these ich9 platforms can do so. Part of this problem has to do with CPU sleep states and to make sure that all the wake up timings are correctly we force them with the recently merged pm_qos infrastructure written by Mark Gross. (See http://lkml.org/lkml/2007/10/4/400). To make code read a bit easier we introduce a _IS_ICH flag so that we don't need to do mac type checks over the code. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: Increment version to 0.2.1Jesse Brandeburg2008-04-25
| | | | | | Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: save and restore pcie/msi state to support EEH recoveryWendy Xiong2008-04-25
| | | | | | | | | | | | To enable EEH support for pci-express network adapters, pcie/msi state needs to be saved and restored for that adapter. Tested this EEH patch with 2ports and 4ports pci-express e1000e adapters. Signed-off-by: Wendy Xiong <wendyx@us.ibm.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* e1000e: cleanup several stats issuesBruce Allan2008-04-25
| | | | | | | | | | | | | | | | | | | | | Several stats registers are completely unused and we just waste pci bus time reading them. We also omit using the high 32 bits of the GORC/ GOTC counters. We can just read clear them and only read the low registers. Mii-tool can also break es2lan if it executes a MII PHY register ioctl while the device is in autonegotiation. Unfortunately it seems that several applications and installations still perform this ioctl call periodically and especially in this crucial startup time. We can fool the ioctl by providing fail safe information that mimics the "down" link state and only perform the dangerous PHY reads once after link comes up to fill in the real values. As long as link stays up the information will not change. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-19 18:41:25 -0500