aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* [XFS] Fixed a few bugs in xfs_buf_associate_memory()Lachlan McIlroy2007-12-09
| | | | | | | | | | | | | | | | | | - calculation of 'page_count' was incorrect as it did not consider the offset of 'mem' into the first page. The logic to bump 'page_count' didn't work if 'len' was <= PAGE_CACHE_SIZE (ie offset = 3k, len = 2k). - setting b_buffer_length to 'len' is incorrect if 'offset' is > 0. Set it to the total length of the buffer. - I suspect that passing a non-aligned address into mem_to_page() for the first page may have been causing issues - don't know but just tidy up that code anyway. SGI-PV: 971596 SGI-Modid: xfs-linux-melb:xfs-kern:30143a Signed-off-by: Lachlan McIlroy <lachlan@sgi.com> Signed-off-by: Christoph Hellwig <hch@infradead.org>
* [XFS] 971064 Various fixups for xfs_bulkstat().Lachlan McIlroy2007-12-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - sanity check for NULL user buffer in xfs_ioc_bulkstat[_compat]() - remove the special case for XFS_IOC_FSBULKSTAT with count == 1. This special case causes bulkstat to fail because the special case uses xfs_bulkstat_single() instead of xfs_bulkstat() and the two functions have different semantics. xfs_bulkstat() will return the next inode after the one supplied while skipping internal inodes (ie quota inodes). xfs_bulkstate_single() will only lookup the inode supplied and return an error if it is an internal inode. - in xfs_bulkstat(), need to initialise 'lastino' to the inode supplied so in cases were we return without examining any inodes the scan wont restart back at zero. - sanity check for valid *ubcountp values. Cannot sanity check for valid ubuffer here because some users of xfs_bulkstat() don't supply a buffer. - checks against 'ubleft' (the space left in the user's buffer) should be against 'statstruct_size' which is the supplied minimum object size. The mixture of checks against statstruct_size and 0 was one of the reasons we were skipping inodes. - if the formatter function returns BULKSTAT_RV_NOTHING and an error and the error is not ENOENT or EINVAL then we need to abort the scan. ENOENT is for inodes that are no longer valid and we just skip them. EINVAL is returned if we try to lookup an internal inode so we skip them too. For a DMF scan if the inode and DMF attribute cannot fit into the space left in the user's buffer it would return ERANGE. We didn't handle this error and skipped the inode. We would continue to skip inodes until one fitted into the user's buffer or we completed the scan. - put back the recalculation of agino (that got removed with the last fix) at the end of the while loop. This is because the code at the start of the loop expects agino to be the last inode examined if it is non-zero. - if we found some inodes but then encountered an error, return success this time and the error next time. If the formatter aborted with ENOMEM we will now return this error but only if we couldn't read any inodes. Previously if we encountered ENOMEM without reading any inodes we returned a zero count and no error which falsely indicated the scan was complete. SGI-PV: 973431 SGI-Modid: xfs-linux-melb:xfs-kern:30089a Signed-off-by: Lachlan McIlroy <lachlan@sgi.com> Signed-off-by: David Chinner <dgc@sgi.com>
* [XFS] Fix dbflush panic in xfs_qm_sync.Donald Douwsma2007-12-09
| | | | | | | | | | | | | | | | The recent behaviour layer removal dropped the check for quotas that have been requested at mount time but have subsequently been turned off. This results in a panic when accessing m_quotainfo which has been freed. This patch adds the check originally made by xfs_qm_syncall() to xfs_qm_sync(). SGI-PV: 969769 SGI-Modid: xfs-linux-melb:xfs-kern:29908a Signed-off-by: Donald Douwsma <donaldd@sgi.com> Signed-off-by: David Chinner <dgc@sgi.com> Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
* [XFS] cleanup fid types messChristoph Hellwig2007-10-19
| | | | | | | | | | | | | | | | | | Currently XFs has three different fid types: struct fid, struct xfs_fid and struct xfs_fid2 with hte latter two beeing identicaly and the first one beeing the same size but an unstructured array with the same size. This patch consolidates all this to alway uuse struct xfs_fid. This patch is required for an upcoming patch series from me that revamps the nfs exporting code and introduces a Linux-wide struct fid. SGI-PV: 970336 SGI-Modid: xfs-linux-melb:xfs-kern:29651a Signed-off-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Lachlan McIlroy <lachlan@sgi.com> Signed-off-by: Tim Shimmin <tes@sgi.com>
* [XFS] fixups after behavior removal merge into mainline gitChristoph Hellwig2007-10-19
| | | | | | | | | Fixup for lack of dmapi support and no quota module support. SGI-PV: 969985 Signed-off-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Tim Shimmin <tes@sgi.com>
* Merge branch 'upstream-linus' of ↵Linus Torvalds2007-10-18
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6 * 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: pcnet32: remove private net_device_stats structure vortex_up should initialize "err" pcnet32: remove compile warnings in non-napi mode pcnet32: fix non-napi packet reception fix EMAC driver for proper napi_synchronize API sky2: shutdown cleanup napi_synchronize: waiting for NAPI forcedeth msi bugfix gianfar: fix obviously wrong #ifdef CONFIG_GFAR_NAPI placement fs_enet: Update for API changes gianfar: remove orphan struct. forcedeth: fix rx-work condition in nv_rx_process_optimized() too
| * pcnet32: remove private net_device_stats structureDon Fry2007-10-17
| | | | | | | | | | | | | | | | | | | | | | | | | | Remove the statistics from the private structure. Use the net_device_stats in netn_device structure. Following Jeff Garzik's massive cleanup Sep 01. pcnet32 was not "low-hanging fruit". Tested x86_64. Signed-off-by: Don Fry <pcnet32@verizon.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * vortex_up should initialize "err"Badari Pulavarty2007-10-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Simple compile warning fix. (against 2.6.23-git12) Thanks, Badari vortex_up() should initialize 'err' for a successful return. drivers/net/3c59x.c: In function `vortex_up': drivers/net/3c59x.c:1494: warning: `err' might be used uninitialized in this function Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * pcnet32: remove compile warnings in non-napi modeDon Fry2007-10-17
| | | | | | | | | | | | | | Remove compile warning when in non-napi mode. Signed-off-by: Don Fry <pcnet32@verizon.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * pcnet32: fix non-napi packet receptionDon Fry2007-10-17
| | | | | | | | | | | | | | | | | | | | | | Recent changes to the driver for the new napi API broke the reception of packets when in non-napi mode. The initialization of napi.weight was removed for the non-napi case leaving the value zero. Tested NAPI and non-NAPI on x86_64. Signed-off-by: Don Fry <pcnet32@verizon.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * fix EMAC driver for proper napi_synchronize APIBenjamin Herrenschmidt2007-10-17
| | | | | | | | | | | | | | | | | | The EMAC driver "fix" was merged by mistake before the dust had settled on the new napi synchronize interface (and before it got merged). The final version of that function is spelled without underscores. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * sky2: shutdown cleanupStephen Hemminger2007-10-17
| | | | | | | | | | | | | | | | | | | | Solve issues with dual port devices due to shared NAPI. * shutting down one device shouldn't kill other one. * suspend shouldn't hang. Also fix potential race between restart and shutdown. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * napi_synchronize: waiting for NAPIStephen Hemminger2007-10-17
| | | | | | | | | | | | | | | | Some drivers with shared NAPI need a synchronization barrier. Also suggested by Benjamin Herrenschmidt for EMAC. Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * forcedeth msi bugfixManfred Spraul2007-10-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | pci_enable_msi() replaces the INTx irq number in pci_dev->irq with the new MSI irq number. The forcedeth driver did not update the copy in netdevice->irq and parts of the driver used the stale copy. See bugzilla.kernel.org, bug 9047. The patch - updates netdevice->irq - replaces all accesses to netdevice->irq with pci_dev->irq. The patch is against 2.6.23.1. IMHO suitable for both 2.6.23 and 2.6.24 Signed-Off-By: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * gianfar: fix obviously wrong #ifdef CONFIG_GFAR_NAPI placementAnton Vorontsov2007-10-17
| | | | | | | | | | | | | | | | | | Erroneous #ifdef introduced by 293c8513398657f6263fcdb03c87f2760cf61be4 causing NAPI-less ethernet malfunctioning. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * fs_enet: Update for API changesScott Wood2007-10-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This driver was recently broken by several changes for which this driver was not (or was improperly) updated: 1. SET_MODULE_OWNER() was removed. 2. netif_napi_add() was only being called when building with the old CPM binding. 3. The received/budget test was backwards. 4. to_net_dev() was wrong -- the device struct embedded in the net_device struct is not the same as the of_platform device in the private struct. 5. napi_disable/napi_enable was being called even when napi was not being used. These changes have been fixed, and napi is now on by default. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * gianfar: remove orphan struct.Sebastian Siewior2007-10-17
| | | | | | | | | | | | | | | | | | struct net_device_stats is no longer used in driver's private struct but in struct net_device. Cc: Li Yang <leoli@freescale.com> Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: Jeff Garzik <jeff@garzik.org>
| * forcedeth: fix rx-work condition in nv_rx_process_optimized() tooIngo Molnar2007-10-17
| | | | | | | | | | | | | | | | | | | | The merge of my previous fix to forcedeth.c, bcb5febb248f7cc1e4a39ff61507f6343ba1c594, lost an important hunk. We need to fix nv_rx_process_optimized() too, as it contains duplicate logic. Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* | Merge master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6Linus Torvalds2007-10-18
|\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6: (37 commits) ide: set drive->autotune in ide_pci_setup_ports() triflex: always tune PIO opti621: always tune PIO cy82c693: always tune PIO cs5520: always tune PIO alim15x3: always tune PIO ide: add IDE_HFLAG_LEGACY_IRQS host flag ide: add IDE_HFLAG_SERIALIZE host flag ide: add IDE_HFLAG_ERROR_STOPS_FIFO host flag piix: add DECLARE_ICH_DEV() macro pdc202xx_old: add DECLARE_PDC2026X_DEV() macro pdc202xx_new: add DECLARE_PDCNEW_DEV() macro aec62xx: no need to disable UDMA in ->init_hwif method for ATP850UF ide: remove .init_setup from ide_pci_device_t serverworks: remove ->init_setup scc_pata: remove ->init_setup pdc202xx_old: remove ->init_setup pdc202xx_new: remove ->init_setup hpt366: remove ->init_setup cmd64x: remove ->init_setup ...
| * | ide: set drive->autotune in ide_pci_setup_ports()Bartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Majority of host drivers using IDE PCI layer set drive->autotune, the only exceptions are: generic.c ns87415.c rz1000.c trm290.c * no ->set_pio_mode method it821x.c: * if memory allocation fails drive->autotune won't be set (but there also won't be ->set_pio_mode method in such case) piix.c: * MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method) However if there is no ->set_pio_mode method there are no changes in behavior w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | triflex: always tune PIOBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | opti621: always tune PIOBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | cy82c693: always tune PIOBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | cs5520: always tune PIOBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | Since cs5520 uses VDMA best PIO mode was tuned anyway by ide_dma_check() but only if DMA was successfully initialized. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | alim15x3: always tune PIOBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: add IDE_HFLAG_LEGACY_IRQS host flagBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add IDE_HFLAG_LEGACY_IRQS host flag to tell ide_pci_setup_ports() to set hwif->irq to legacy IRQ 14/15 (iff hwif->irq is not already set) and convert atiixp, piix, serverworks, sis5513 and slc90e66 host drivers to use it. While at it: * In piix.c add IDE_HFLAGS_PIIX define and don't use ->init_hwif for MPIIX. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: add IDE_HFLAG_SERIALIZE host flagBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | Add IDE_HFLAG_SERIALIZE host flag to tell ide_pci_setup_ports() to set hwif/mate->serialized and convert aec62xx, cs5530 and sc1200 host drivers to use it. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: add IDE_HFLAG_ERROR_STOPS_FIFO host flagBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | Add IDE_HFLAG_ERROR_STOPS_FIFO host flag and use it instead of hwif->err_stops_fifo. As a side-effect this change fixes hwif->err_stops_fifo not being restored by ide_hwif_restore(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | piix: add DECLARE_ICH_DEV() macroBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add DECLARE_ICH_DEV() macro. While at it: * Add init_hwif_ich() (->init_hwif method) for ICH controllers. * Rename init_chipset_piix() to init_chipset_ich() and use it only for ICH controllers. * Remove no longer needed piix_is_ichx() helper. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | pdc202xx_old: add DECLARE_PDC2026X_DEV() macroBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | pdc202xx_new: add DECLARE_PDCNEW_DEV() macroBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | aec62xx: no need to disable UDMA in ->init_hwif method for ATP850UFBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * No need to disable UDMA in ->init_hwif method for ATP850UF (and since we now always tune PIO it will be disabled by ->set_pio_mode calls anyway). * Bump driver version. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: remove .init_setup from ide_pci_device_tBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | Now that all users were fixed we can safely remove it. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | serverworks: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Merge init_setup_{svwks,csb6}() into svwks_init_one(). While at it: * Remove redundant dev->device checks. * Operate on a local copy of serverworks_chipsets[] entry. * Use pci_resource_start(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | scc_pata: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | pdc202xx_old: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | * Split off pdc202ata4_fixup_irq() helper from init_setup_pdc202ata4(). * Merge init_setup_{pdc202ata4,pdc20265,pdc202xx}() into pdc202xx_init_one(). Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | pdc202xx_new: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Split off pdc20270_get_dev2() helper from init_setup_pdc20270(). * Merge init_setup_{pdcnew,pdc20270,pdc20276}() into pdc202new_init_one(). While at it: * Change KERN_ level of interrupt fixup message from KERN_WARNING to KERN_INFO. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | hpt366: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Split off hpt{374,371,366}_init() helper from init_setup_hpt{374,371,366}(). * Merge init_setup_{374,372n,371,372a,302,366}() into hpt366_init_one(). While at it: * Use "HPT36x" name for HPT366/HPT368 chipsets. * Add .chip_name to struct hpt_info and use it to set set d->name. * Convert .max_ultra in struct hpt_info to .udma_mask and use it to set d->udma_mask. * Fix hpt302 to use HPT302_ALLOW_ATA133_6 define. * Change HPT366/HPT374 interrupt fixup message from KERN_WARNING to KERN_INFO. * Use the second hpt366_chipsets[] entry for HPT37x chipsets using HPT36x PCI device ID and fix .enablebits/.host_flags for HPT36x hpt366_chipsets[] entry. * Bump driver version. Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | cmd64x: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | Merge init_setup_{cmd64x,cmd646}() into cmd64x_init_one(). Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | aec62xx: remove ->init_setupBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Merge init_setup_{aec62xx,aec6x80}() into aec62xx_init_one(). While at it: * Use id->driver_data instead of dev->device. * Use ATA_UDMA6 define. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: use I/O ops directly part #2 (take 2)Bartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | v2: - bump host driver versions (as suggested by Sergei) - use I/O ops directly in drivers/ide/setup-pci.c Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: use pci_dev->revisionBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID so they were not converted by commit 44c10138fd4bbc4b6d6bff0873c24902f2a9da65. Cc: Auke Kok <auke-jan.h.kok@intel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | cmd64x: Use dev->revisionAuke Kok2007-10-18
| | | | | | | | | | | | | | | | | | Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | amd74xx: Omit PCI_REVISION_ID readAuke Kok2007-10-18
| | | | | | | | | | | | | | | | | | Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: add ->mwdma_mask and ->swdma_mask to ide_pci_device_t (take 2)Bartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t. * Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif method may still override them). * Convert IDE PCI host drivers to use ide_pci_device_t DMA masks. While at it: * Use ATA_{UDMA,MWDMA,SWDMA}* defines. * hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345. * serverworks.c: fix DMA masks being set before checking DMA base. v2: * Add missing masks to DECLARE_GENERIC_PCI_DEV() macro. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | pdc202xx_old: remove broken SWDMA supportBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | Documentation doesn't mention SWDMA and moreover all timings used for SWDMA modes were over-clocked when compared to ATA spec. Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: add IDE_HFLAG_NO_LBA48 and IDE_HFLAG_NO_LBA48_DMA host flagsBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma] and then remove no longer needed hwif->no_lba48[_dma]. As a side-effect this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore(). Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: remove ->init_setup_dma from ide_pci_device_t (take 2)Bartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * Make ide_pci_device_t.host_flags u32 and add IDE_HFLAG_CS5520 host flag. * Pass ide_pci_device_t *d to setup-pci.c::ide_get_or_set_dma_base() and use d->name instead of hwif->cds->name. * Set IDE_HFLAG_CS5520 host flag in cs5520 host driver and use it in ide_get_or_set_dma_base() to find out which PCI BAR to use, remove no longer needed cs5520.c::cs5520_init_setup_dma() and ide_pci_device_t.init_setup_dma. This fixes PCI bus-mastering not being checked for CS5510/CS5520 hosts. v2: * It is wrong to check simplex bits on CS5510/CS5520 as v1 did. (Noticed by Alan). Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: add IDE_HFLAG_NO_{DMA,AUTODMA} host flagsBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags. Convert all host drivers using ide_pci_device_t to use these flags instead of d->autodma and then remove no longer needed d->autodma. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
| * | ide: add IDE_HFLAG_BOOTABLE host flagBartlomiej Zolnierkiewicz2007-10-18
| | | | | | | | | | | | | | | | | | | | | | | | Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define. Convert all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD} instead of d->bootable and then remove no longer needed d->bootable. Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
generated by cgit v1.2.2 (git 2.25.0) at 2024-12-27 08:36:31 -0500