1 files changed, 18 insertions, 13 deletions

diff --git a/arch/arm/mach-mx5/board-cpuimx51sd.c b/arch/arm/mach-mx5/board-cpuimx51sd.c
index ad931895d8b6..29b180823bf5 100644
--- a/arch/arm/mach-mx5/board-cpuimx51sd.c
+++ b/arch/arm/mach-mx5/board-cpuimx51sd.c
@@ -42,6 +42,7 @@
 
 #include "devices-imx51.h"
 #include "devices.h"
+#include "cpu_op-mx51.h"
 
 #define USBH1_RST               IMX_GPIO_NR(2, 28)
 #define ETH_RST                 IMX_GPIO_NR(2, 31)
@@ -109,7 +110,7 @@ static iomux_v3_cfg_t eukrea_cpuimx51sd_pads[] = {
 
         /* Touchscreen */
         /* IRQ */
-        _MX51_PAD_CSI1_D8__GPIO3_12 | MUX_PAD_CTRL(PAD_CTL_PUS_22K_UP |
+        _MX51_PAD_GPIO_NAND__GPIO_NAND | MUX_PAD_CTRL(PAD_CTL_PUS_22K_UP |
                         PAD_CTL_PKE | PAD_CTL_SRE_FAST |
                         PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
 };
@@ -118,15 +119,9 @@ static const struct imxuart_platform_data uart_pdata __initconst = {
         .flags = IMXUART_HAVE_RTSCTS,
 };
 
-static int ts_get_pendown_state(void)
-{
-        return gpio_get_value(TSC2007_IRQGPIO) ? 0 : 1;
-}
-
 static struct tsc2007_platform_data tsc2007_info = {
         .model                  = 2007,
         .x_plate_ohms           = 180,
-        .get_pendown_state      = ts_get_pendown_state,
 };
 
 static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
@@ -167,7 +162,10 @@ static int initialize_otg_port(struct platform_device *pdev)
         v |= MX51_USB_PLL_DIV_19_2_MHZ;
         __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
         iounmap(usb_base);
-        return 0;
+
+        mdelay(10);
+
+        return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
 }
 
 static int initialize_usbh1_port(struct platform_device *pdev)
@@ -186,13 +184,16 @@ static int initialize_usbh1_port(struct platform_device *pdev)
         __raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN,
                         usbother_base + MX51_USB_CTRL_1_OFFSET);
         iounmap(usb_base);
-        return 0;
+
+        mdelay(10);
+
+        return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
+                        MXC_EHCI_ITC_NO_THRESHOLD);
 }
 
 static struct mxc_usbh_platform_data dr_utmi_config = {
         .init           = initialize_otg_port,
         .portsc = MXC_EHCI_UTMI_16BIT,
-        .flags  = MXC_EHCI_INTERNAL_PHY,
 };
 
 static struct fsl_usb2_platform_data usb_pdata = {
@@ -203,7 +204,6 @@ static struct fsl_usb2_platform_data usb_pdata = {
 static struct mxc_usbh_platform_data usbh1_config = {
         .init           = initialize_usbh1_port,
         .portsc = MXC_EHCI_MODE_ULPI,
-        .flags  = (MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_ITC_NO_THRESHOLD),
 };
 
 static int otg_mode_host;
@@ -242,7 +242,7 @@ static struct mcp251x_platform_data mcp251x_info = {
 static struct spi_board_info cpuimx51sd_spi_device[] = {
         {
                 .modalias        = "mcp2515",
-                .max_speed_hz    = 6500000,
+                .max_speed_hz    = 10000000,
                 .bus_num         = 0,
                 .mode           = SPI_MODE_0,
                 .chip_select     = 0,
@@ -269,6 +269,10 @@ static void __init eukrea_cpuimx51sd_init(void)
         mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
                                         ARRAY_SIZE(eukrea_cpuimx51sd_pads));
 
+#if defined(CONFIG_CPU_FREQ_IMX)
+        get_cpu_op = mx51_get_cpu_op;
+#endif
+
         imx51_add_imx_uart(0, &uart_pdata);
         imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);
 
@@ -329,7 +333,8 @@ MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
         /* Maintainer: Eric Bénard <eric@eukrea.com> */
         .boot_params = MX51_PHYS_OFFSET + 0x100,
         .map_io = mx51_map_io,
+        .init_early = imx51_init_early,
         .init_irq = mx51_init_irq,
-        .init_machine = eukrea_cpuimx51sd_init,
         .timer = &mxc_timer,
+        .init_machine = eukrea_cpuimx51sd_init,
 MACHINE_END