aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/wireless/ath
Commit message (Collapse)AuthorAge
...
| | * | ath10k: fix throughput regression in multi client modeRajkumar Manoharan2016-09-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 7a0adc83f34d ("ath10k: improve tx scheduling") is causing severe throughput drop in multi client mode. This issue is originally reported in veriwave setup with 50 clients with TCP downlink traffic. While increasing number of clients, the average throughput drops gradually. With 50 clients, the combined peak throughput is decreased to 98 Mbps whereas reverting given commit restored it to 550 Mbps. Processing txqs for every tx completion is causing overhead. Ideally for management frame tx completion, pending txqs processing can be avoided. The change partly reverts the commit "ath10k: improve tx scheduling". Processing pending txqs after all skbs tx completion will yeild enough room to burst tx frames. Fixes: 7a0adc83f34d ("ath10k: improve tx scheduling") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: implement NAPI supportRajkumar Manoharan2016-09-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add NAPI support for rx and tx completion. NAPI poll is scheduled from interrupt handler. The design is as below - on interrupt - schedule napi and mask interrupts - on poll - process all pipes (no actual Tx/Rx) - process Rx within budget - if quota exceeds budget reschedule napi poll by returning budget - process Tx completions and update budget if necessary - process Tx fetch indications (pull-push) - push any other pending Tx (if possible) - before resched or napi completion replenish htt rx ring buffer - if work done < budget, complete napi poll and unmask interrupts This change also get rid of two tasklets (intr_tq and txrx_compl_task). Measured peak throughput with NAPI on IPQ4019 platform in controlled environment. No noticeable reduction in throughput is seen and also observed improvements in CPU usage. Approx. 15% CPU usage got reduced in UDP uplink case. DL: AP DUT Tx UL: AP DUT Rx IPQ4019 (avg. cpu usage %) ======== TOT +NAPI =========== ============= TCP DL 644 Mbps (42%) 645 Mbps (36%) TCP UL 673 Mbps (30%) 675 Mbps (26%) UDP DL 682 Mbps (49%) 680 Mbps (49%) UDP UL 720 Mbps (28%) 717 Mbps (11%) Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath9k: mark ath_fill_led_pin() staticBaoyou Xie2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We get 1 warning about global functions without a declaration in the ath9k gpio driver when building with W=1: drivers/net/wireless/ath/ath9k/gpio.c:25:6: warning: no previous prototype for 'ath_fill_led_pin' [-Wmissing-prototypes] In fact, this function is only used in the file in which it is declared and don't need a declaration, but can be made static. so this patch marks it 'static'. Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: fix spelling mistake "montior" -> "monitor"Colin Ian King2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Trivial fix to spelling mistake in ath10k_warn message. Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: Fix broken NULL func data frame status for 10.4Mohammed Shafi Shajakhan2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Older firmware with HTT delivers incorrect tx status for null func frames to driver, but this fixed in 10.2 and 10.4 firmware versions. Also this workaround results in reporting of incorrect null func status for 10.4. Fix this is by introducing a firmware feature flag for 10.4 so that this workaround is skipped and proper tx status for null func frames are reported Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: replace config_enabled() with IS_REACHABLE()Masahiro Yamada2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 97f2645f358b ("tree-wide: replace config_enabled() with IS_ENABLED()") mostly did away with config_enabled(). This is one of the postponed TODO items as config_enabled() is used for a tristate option here. Theoretically, config_enabled() is equivalent to IS_BUILTIN(), but I guess IS_REACHABLE() is the best fit for this case because both CONFIG_HWMON and CONFIG_ATH10K are tristate. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: Added support for extended dbglog module id for 10.4Maharaja Kennadyrajan2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For 10.4 fw versions, dbglog module id has been extended from u32 to u64, hence this patch fixes the same in the ath10k driver side. This patch doesn't break the older 10.4 releases. The FW change is already present in the older FWs. Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: use complete() instead complete_all()Daniel Wagner2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | There is only one waiter for the completion, therefore there is no need to use complete_all(). Let's make that clear by using complete() instead of complete_all(). The usage pattern of the completion is: waiter context waker context scan.started ------------ ath10k_start_scan() lockdep_assert_held(conf_mutex) auth10k_wmi_start_scan() wait_for_completion_timeout(scan.started) ath10k_wmi_event_scan_start_failed() complete(scan.started) ath10k_wmi_event_scan_started() complete(scan.started) scan.completed -------------- ath10k_scan_stop() lockdep_assert_held(conf_mutex) ath10k_wmi_stop_scan() wait_for_completion_timeout(scan.completed) __ath10k_scan_finish() complete(scan.completed) scan.on_channel --------------- ath10k_remain_on_channel() mutex_lock(conf_mutex) ath10k_start_scan() wait_for_completion_timeout(scan.on_channel) ath10k_wmi_event_scan_foreign_chan() complete(scan.on_channel) offchan_tx_completed -------------------- ath10k_offchan_tx_work() mutex_lock(conf_mutex) reinit_completion(offchan_tx_completed) wait_for_completion_timeout(offchan_tx_completed) ath10k_report_offchain_tx() complete(offchan_tx_completed) install_key_done ---------------- ath10k_install_key() lockep_assert_held(conf_mutex) reinit_completion(install_key_done) wait_for_completion_timeout(install_key_done) ath10k_htt_t2h_msg_handler() complete(install_key_done) vdev_setup_done --------------- ath10k_monitor_vdev_start() lockdep_assert_held(conf_mutex) reinit_completion(vdev_setup_done) ath10k_vdev_setup_sync() wait_for_completion_timeout(vdev_setup_done) ath10k_wmi_event_vdev_start_resp() complete(vdev_setup_done) ath10k_monitor_vdev_stop() lockdep_assert_held(conf_mutex) reinit_completion(vdev_setup_done() ath10k_vdev_setup_sync() wait_for_completion_timeout(vdev_setup_done) ath10k_wmi_event_vdev_stopped() complete(vdev_setup_done) thermal.wmi_sync ---------------- ath10k_thermal_show_temp() mutex_lock(conf_mutex) reinit_completion(thermal.wmi_sync) wait_for_completion_timeout(thermal.wmi_sync) ath10k_thermal_event_temperature() complete(thermal.wmi_sync) bss_survey_done --------------- ath10k_mac_update_bss_chan_survey lockdep_assert_held(conf_mutex) reinit_completion(bss_survey_done) wait_for_completion_timeout(bss_survey_done) ath10k_wmi_event_pdev_bss_chan_info() complete(bss_survey_done) All complete() calls happen while the conf_mutex is taken. That means at max one waiter is possible. Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: fix sending frame in management path in push txq logicAshok Raj Nagarajan2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the wake tx queue path, we are not checking if the frame to be sent takes management path or not. For eg. QOS null func frame coming here will take the management path. Since we are not incrementing the descriptor counter (num_pending_mgmt_tx) w.r.t tx management, on tx completion it is possible to see negative values. When the above counter reaches a negative value, we will not be sending a probe response out. if (is_presp && ar->hw_params.max_probe_resp_desc_thres < htt->num_pending_mgmt_tx) For IPQ4019, max_probe_resp_desc_thres (u32) is 24 is compared against num_pending_mgmt_tx (int) and the above condtions comes true if the counter is negative and we drop the probe response. To avoid this, check on the wake tx queue path as well for the tx path of the frame and increment the appropriate counters Fixes: cac085524cf1 "ath10k: move mgmt descriptor limit handle under mgmt_tx" Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: improve wake_tx_queue ops performanceRajkumar Manoharan2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | txqs_lock is interfering with wake_tx_queue submitting more frames. so queues don't get filled in and don't keep firmware/hardware busy enough. This change helps to reduce the txqs_lock contention and wake_tx_queue() blockage to being possible in txrx_unref(). To reduce turn around time of wake_tx_queue ops and to maintain fairness among all txqs, the callback is updated to push first txq alone from pending list for every wake_tx_queue call. Remaining txqs will be processed later upon tx completion. Below improvements are observed in push-only mode and validated on IPQ4019 platform. With this change, in AP mode ~10Mbps increase is observed in downlink (AP -> STA) traffic and approx. 5-10% of CPU usage is reduced. Major improvement is observed in 1-hop Mesh mode topology in 11ACVHT80. Compared to Infra mode, CPU overhead is higher in Mesh mode due to path lookup and no fast-xmit support. So reducing spin lock contention is helping in Mesh. TOT +change -------- -------- TCP DL 545 Mbps 595 Mbps TCP UL 555 Mbps 585 Mbps Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: suppress warnings when getting wmi WDS peer event idMohammed Shafi Shajakhan2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 'WMI_10_4_WDS_PEER_EVENTID' is not yet handled/implemented for WDS mode, as of now suppress the warning message "Unknown eventid: 36903" Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: fix group privacy action frame decryption for qca4019Rajkumar Manoharan2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Recent commit 46f6b06050b7 ("mac80211: Encrypt "Group addressed privacy" action frames") encrypts group privacy action frames. But qca99x0 family chipset delivers broadcast/multicast management frames as encrypted and it should be decrypted by mac80211. Setting RX_FLAG_DECRYPTED stats for those frames is breaking mesh connection establishment. Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: hide kernel addresses from logs using %pK format specifierMaharaja Kennadyrajan2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With the %pK format specifier we hide the kernel addresses with the help of kptr_restrict sysctl. In this patch, %p is changed to %pK in the driver code. The sysctl is documented in Documentation/sysctl/kernel.txt. Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: Add WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT wmi serviceTamizh chelvam2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT service has missed in the commit 7e247a9e88dc ("ath10k: add dynamic tx mode switch config support for qca4019"). This patch adds the service to avoid mismatch between host and target. Fixes: 7e247a9e88dc ("ath10k: add dynamic tx mode switch config support for qca4019") Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: extract firmware version from file headerLior David2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the FW version is taken from the sw_version field of the FW ready event. This version is based on internal version control revision and it is difficult to map to actual FW version. Fix this by using the actual FW version stored in the FW file header record. Signed-off-by: Lior David <qca_liord@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: extract firmware capabilities from FW fileLior David2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When driver is loaded, extract a capabilities record from the FW file. This record contains bits indicating which optional features are supported by this FW. The driver can use this information to determine which functionality to support and/or expose to user space. The extraction is done before wiphy structure is registered, because the capabilities can affect information published by the this structure. Signed-off-by: Lior David <qca_liord@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: align to latest auto generated wmi.hLior David2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Align to latest version of the auto generated wmi file describing the interface with FW. Signed-off-by: Lior David <qca_liord@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: fix protection of wil->scan_requestLior David2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the places that check wil->scan_request and call cfg80211_scan_done are not consistently protected, so there is a risk that cfg80211_scan_done will be called with NULL scan_request, causing a kernel crash. Fix this by using p2p_wdev_mutex in few other places that access scan_request. This makes sense since scan_request may point to p2p_wdev, and it is not worth the extra complexity of adding a new mutex. Signed-off-by: Lior David <qca_liord@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: fix spurious tx/rx during bootMichal Kazior2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | HW Rx filters and masks are not configured properly by firmware during boot sequences. The MAC_PCU_ADDR1 is set to 0s instead of 1s which allows the HW to ACK any frame that passes through MAC_PCU_RX_FILTER. The MAC_PCU_RX_FILTER itself is misconfigured on boot as well. The combination of these bugs ended up with the following manifestations: - "no channel configured; ignoring frame(s)!" warnings in the driver - spurious ACKs (transmission) on the air during firmware bootup sequences The former was a long standing and known bug originally though mostly harmless. However Marek recently discovered that this problem also involves ACKing *all* frames the HW receives (including beacons ;). Such frames are delivered to host and generate the former warning as well. This could be a problem with regulatory compliance in some rare cases (e.g. Taiwan which forbids transmissions on channel 36 which is the default bootup channel on 5Ghz band cards). The good news is that it'd require someone else to violate regulatory first to coerce our device to generate and transmit an ACK. The problem could be reproduced in a rather busy environment that has a lot of APs. The likelihood could be increased by injecting an msleep() of 5000 or longer immediately after ath10k_htt_setup() in ath10k_core_start(). The reason why the former warnings were only showing up seldom is because the device was either quickly reset again (i.e. during firmware probing) or wmi vdev was created (which fixes hw and fw states). It is technically possible for host driver to override adequate hw registers however this can't work reliably because the bug root cause lies in incorrect firmware state on boot (internal structure used to program MAC_PCU_ADDR1 is not properly initialized) and only vdev create/delete events can fix it. This is why the patch takes dummy vdev approach. This could be fixed in firmware as well but having this fixed in driver is more robust, most notably when thinking of users of older firmware such as 999.999.0.636. Reported-by: Marek Puzyniak <marek.puzyniak@tieto.com> Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: add wmi command barrier utilityMichal Kazior2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This allows placing command barriers for explicit serializing and synchronizing state. Useful for future driver development. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: implement wmi echo eventMichal Kazior2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Will be useful for implementing command barriers. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: implement wmi echo commandMichal Kazior2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Will be useful for implementing command barriers. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: add testmode support for 10.4 firmwareTamizh chelvam2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds testmode support for 10.4 based chipsets and added code swap support for UTF binary. Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: handle testmode events for 10.2 and 10.4 based firmwareTamizh chelvam2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently testmode events for 10.x firmware are processed from 10.1 wmi event processing. This patch is used to handle testmode events in 10.2 and 10.4 based firmware. Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath10k: move firmware_swap_code_seg_info to ath10k_fw_fileTamizh chelvam2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Preparation to make use of firmware_swap_code_seg_info for UTF binary. Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: fix wiphy registration sequenceLior David2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently wiphy structure is initialized and registered in wil_if_alloc, before some information is available such as MAC address and capabilities. As a result there is a small chance user space will get incorrect information from calls such as NL80211_CMD_GET_WIPHY. Fix this by seperating the registration and moving it to wil_if_add which is executed later, after all relevant information is known. Signed-off-by: Lior David <qca_liord@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: prevent usage of incorrect TX hwtailMaya Erez2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | txdata->enabled is used in order to determine if the TX vring is valid. As the data transmit is handled in a different context, in case txdata->enabled is set before vring->hwtail is updated, an old or corrupted vring->hwtail can be used. Protect setting of txdata->enabled and vring->hwtail to prevent a case where TX vring start handling TX packets before setting vring->hwtail. Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: Fix driver down flowLazar Alexei2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Stations disconnection is executed as part of wil_reset so no need to do it in wil_down. Removal of the disconnect operation will also preserve the lock of wil->mutex during the whole reset flow and prevent handling of connect event while resetting. Set wil_status_resetting in earlier stage in the flow to prevent double resetting call in case communication with FW fails while bringing the interface down. Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: fix stop p2p device handlingMaya Erez2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | fix stop p2p device handling to identify between search and listen and update the upper layers with the appropriate notification. The stop of p2p radio operations also needs to be performed in __wil_down. Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: change HALP logging category to IRQLior David2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Change the logging category of HALP functions from MISC to IRQ, since the HALP mechanism is closely related to interrupts. Both HALP and IRQ create a heavy load of logging messages when enabled, so their logging is typically disabled during normal debug scenarios. Having them in the same logging category will make it easier to disable logging for both in one go. Signed-off-by: Lior David <qca_liord@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: support rx key setting for all TIDsMaya Erez2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | According to the spec the PN should be calculated per TID. In the current implementation, the PN and key_set were set only for TID 0, therefore only traffic for TID 0 was supported. In order to support all TIDs, the key_set and PN should be set for all the TIDs. Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: fix HALP handling in case of HALP vote time-outMaya Erez2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In case HALP vote times out, we need to mask the HALP IRQ, as done in case the interrupt is received, as this interrupt should be set until completion of the low latency operation. Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | wil6210: align to latest auto generated wmi.hMaya Erez2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Align to latest version of the auto generated wmi file describing the interface with FW. Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath9k: consider return code onEduardo Abinader2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | just to comply with current ath9k_hw_nvram_read to return value, hence behaving reacting accordingly. Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| | * | ath9k: fix misleading indentBob Copeland2016-08-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fixes smatch warning: ath9k_vif_iter_set_beacon() warn if statement not indented Signed-off-by: Bob Copeland <me@bobcopeland.com> Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
| * | | ath5k: fix EEPROM dumping via debugfsSergey Ryazanov2016-09-03
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | EEPROM size calculated in 16-bit words, so we should take into account this fact during buffer allocation. CC: Jiri Slaby <jirislaby@gmail.com> CC: Nick Kossifidis <mickflemm@gmail.com> CC: Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
| * | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2016-08-18
| |\ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Minor overlapping changes for both merge conflicts. Resolution work done by Stephen Rothwell was used as a reference. Signed-off-by: David S. Miller <davem@davemloft.net>
| * | | net: wireless: ath: ar5523: ar5523: don't print error when allocating urb failsWolfram Sang2016-08-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | kmalloc will print enough information in case of failure. Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | | Merge tag 'driver-core-4.9-rc1' of ↵Linus Torvalds2016-10-03
|\ \ \ \ | |_|_|/ |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core updates from Greg KH: "Here are the "big" driver core patches for 4.9-rc1. Also in here are a number of debugfs fixes that cropped up due to the changes that happened in 4.8 for that filesystem. Overall, nothing major, just a few fixes and cleanups. All of these have been in linux-next with no reported issues" * tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits) drivers: dma-coherent: Move spinlock in dma_alloc_from_coherent() drivers: dma-coherent: Fix DMA coherent size for less than page MAINTAINERS: extend firmware_class maintainer list debugfs: propagate release() call result driver-core: platform: Catch errors from calls to irq_get_irq_data sysfs print name of undiscoverable attribute group carl9170: fix debugfs crashes b43legacy: fix debugfs crash b43: fix debugfs crash debugfs: introduce a public file_operations accessor device core: Remove deprecated create_singlethread_workqueue drivers/base dmam_declare_coherent_memory leaks platform: don't return 0 from platform_get_irq[_byname]() on error cpu: clean up register_cpu func dma-mapping: use vma_pages(). drivers: dma-coherent: use vma_pages(). attribute_container: Fix typo base: soc: make it explicitly non-modular drivers: base: dma-mapping: page align the size when unmap_kernel_range platform driver: fix use-after-free in platform_device_del() ...
| * | | carl9170: fix debugfs crashesChristian Lamparter2016-09-21
| | |/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ben Greear reported: > I see lots of instability as soon as I load up the carl9710 NIC. > My application is going to be poking at it's debugfs files... > > BUG: KASAN: slab-out-of-bounds in carl9170_debugfs_read+0xd5/0x2a0 > [carl9170] at addr 0xffff8801bc1208b0 > Read of size 8 by task btserver/5888 > ======================================================================= > BUG kmalloc-256 (Tainted: G W ): kasan: bad access detected > ----------------------------------------------------------------------- > > INFO: Allocated in seq_open+0x50/0x100 age=2690 cpu=2 pid=772 >... This breakage was caused by the introduction of intermediate fops in debugfs by commit 9fd4dcece43a ("debugfs: prevent access to possibly dead file_operations at file open") Thankfully, the original/real fops are still available in d_fsdata. Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Cc: stable <stable@vger.kernel.org> # 4.7+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* | | ath9k: bring back direction setting in ath9k_{start_stop}Giedrius Statkevičius2016-09-07
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A regression was introduced in commit id 79d4db1214a ("ath9k: cleanup led_pin initial") that broken the WLAN status led on my laptop with AR9287 after suspending and resuming. Steps to reproduce: * Suspend (laptop) * Resume (laptop) * Observe that the WLAN led no longer turns ON/OFF depending on the status and is always red Even though for my case it only needs to be set to OUT in ath9k_start but for consistency bring back the IN direction setting as well. Fixes: 79d4db1214a0 ("ath9k: cleanup led_pin initial") Cc: Miaoqing Pan <miaoqing@codeaurora.org> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: <stable@vger.kernel.org> # 4.7+ Link: https://bugzilla.kernel.org/show_bug.cgi?id=151711 Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com> [kvalo@qca.qualcomm.com: improve commit log] Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* | | ath9k: fix AR5416 access GPIO warningMiaoqing Pan2016-09-02
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The warning was seen on AR5416 chip, which invoke ath9k_hw_gio_get() before the GPIO initialized correctly. WARNING: CPU: 1 PID: 1159 at ~/drivers/net/wireless/ath/ath9k/hw.c:2776 ath9k_hw_gpio_get+0x148/0x1a0 [ath9k_hw] ... CPU: 1 PID: 1159 Comm: systemd-udevd Not tainted 4.7.0-rc7-aptosid-amd64 #1 aptosid 4.7~rc7-1~git92.slh.3 Hardware name: /DH67CL, BIOS BLH6710H.86A.0160.2012.1204.1156 12/04/2012 0000000000000286 00000000f912d633 ffffffff81290fd3 0000000000000000 0000000000000000 ffffffff81063fd4 ffff88040c6dc018 0000000000000000 0000000000000002 0000000000000000 0000000000000100 ffff88040c6dc018 Call Trace: [<ffffffff81290fd3>] ? dump_stack+0x5c/0x79 [<ffffffff81063fd4>] ? __warn+0xb4/0xd0 [<ffffffffa0668fb8>] ? ath9k_hw_gpio_get+0x148/0x1a0 [ath9k_hw] Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Reported-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* | | ath10k: Remove driver log suggesting QCA9887 support is experimentalMohammed Shafi Shajakhan2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | Support for QCA9887 is no longer experimental and if there are any issues we need to address them Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* | | ath10k: fix get rx_status from htt contextAshok Raj Nagarajan2016-08-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On handling amsdu on rx path, get the rx_status from htt context. Without this fix, we are seeing warnings when running DBDC traffic like this. WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4105 ieee80211_rx_napi+0x88/0x7d8 [mac80211]() [ 1715.878248] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.18.21 #1 [ 1715.878273] [<c001d3f4>] (unwind_backtrace) from [<c001a4b0>] (show_stack+0x10/0x14) [ 1715.878293] [<c001a4b0>] (show_stack) from [<c01bee64>] (dump_stack+0x70/0xbc) [ 1715.878315] [<c01bee64>] (dump_stack) from [<c002a61c>] (warn_slowpath_common+0x64/0x88) [ 1715.878339] [<c002a61c>] (warn_slowpath_common) from [<c002a6d0>] (warn_slowpath_null+0x18/0x20) [ 1715.878395] [<c002a6d0>] (warn_slowpath_null) from [<bf4caa98>] (ieee80211_rx_napi+0x88/0x7d8 [mac80211]) [ 1715.878474] [<bf4caa98>] (ieee80211_rx_napi [mac80211]) from [<bf568658>] (ath10k_htt_t2h_msg_handler+0xb48/0xbfc [ath10k_core]) [ 1715.878535] [<bf568658>] (ath10k_htt_t2h_msg_handler [ath10k_core]) from [<bf568708>] (ath10k_htt_t2h_msg_handler+0xbf8/0xbfc [ath10k_core]) [ 1715.878597] [<bf568708>] (ath10k_htt_t2h_msg_handler [ath10k_core]) from [<bf569160>] (ath10k_htt_txrx_compl_task+0xa54/0x1170 [ath10k_core]) [ 1715.878639] [<bf569160>] (ath10k_htt_txrx_compl_task [ath10k_core]) from [<c002db14>] (tasklet_action+0xb4/0x130) [ 1715.878659] [<c002db14>] (tasklet_action) from [<c002d110>] (__do_softirq+0xe0/0x210) [ 1715.878678] [<c002d110>] (__do_softirq) from [<c002d4b4>] (irq_exit+0x84/0xe0) [ 1715.878700] [<c002d4b4>] (irq_exit) from [<c005a544>] (__handle_domain_irq+0x98/0xd0) [ 1715.878722] [<c005a544>] (__handle_domain_irq) from [<c00085f4>] (gic_handle_irq+0x38/0x5c) [ 1715.878741] [<c00085f4>] (gic_handle_irq) from [<c0009680>] (__irq_svc+0x40/0x74) [ 1715.878753] Exception stack(0xc05f9f50 to 0xc05f9f98) [ 1715.878767] 9f40: ffffffed 00000000 00399e1e c000a220 [ 1715.878786] 9f60: 00000000 c05f6780 c05f8000 00000000 c05f5db8 ffffffed c05f8000 c04d1980 [ 1715.878802] 9f80: 00000000 c05f9f98 c0018110 c0018114 60000013 ffffffff [ 1715.878822] [<c0009680>] (__irq_svc) from [<c0018114>] (arch_cpu_idle+0x2c/0x50) [ 1715.878844] [<c0018114>] (arch_cpu_idle) from [<c00530d4>] (cpu_startup_entry+0x108/0x234) [ 1715.878866] [<c00530d4>] (cpu_startup_entry) from [<c05c7be0>] (start_kernel+0x33c/0x3b8) [ 1715.878879] ---[ end trace 6d5e1cc0fef8ed6a ]--- [ 1715.878899] ------------[ cut here ]------------ Fixes: 18235664e7f9 ("ath10k: cleanup amsdu processing for rx indication") Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* | | ath9k: fix using sta->drv_priv before initializing itFelix Fietkau2016-08-22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A station pointer can be passed to the driver on tx, before it has been marked as associated. Since ath9k_sta_state was initializing the entry too late, it resulted in some spurious crashes. Fixes: df3c6eb34da5 ("ath9k: Use sta_state() callback") Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* | | ath9k: fix client mode beacon configurationFelix Fietkau2016-08-22
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For pure station mode, iter_data.primary_beacon_vif was used and passed to ath_beacon_config, but not set to the station vif. This was causing the following warning: [ 100.310919] ------------[ cut here ]------------ [ 100.315683] WARNING: CPU: 0 PID: 7 at compat-wireless-2016-06-20/drivers/net/wireless/ath/ath9k/beacon.c:642 ath9k_calculate_summary_state+0x250/0x60c [ath9k]() [ 100.402028] CPU: 0 PID: 7 Comm: kworker/u2:1 Tainted: G W 4.4.15 #5 [ 100.409676] Workqueue: phy0 ieee80211_ibss_leave [mac80211] [ 100.415351] Stack : 8736e98c 870b4b20 87a25b54 800a6800 8782a080 80400d63 8039b96c 00000007 [ 100.415351] 803c5edc 87875914 80400000 800a47cc 87a25b54 800a6800 803a0fd8 80400000 [ 100.415351] 00000003 87875914 80400000 80094ae0 87a25b54 8787594c 00000000 801ef308 [ 100.415351] 803ffe70 801ef300 87193d58 87b3a400 87b3ad00 70687930 00000000 00000000 [ 100.415351] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 100.415351] ... [ 100.451703] Call Trace: [ 100.454235] [<800a6800>] vprintk_default+0x24/0x30 [ 100.459110] [<800a47cc>] printk+0x2c/0x38 [ 100.463190] [<800a6800>] vprintk_default+0x24/0x30 [ 100.468072] [<80094ae0>] print_worker_info+0x148/0x174 [ 100.473378] [<801ef308>] serial8250_console_putchar+0x0/0x44 [ 100.479122] [<801ef300>] wait_for_xmitr+0xc4/0xcc [ 100.484014] [<87193d58>] ieee80211_ibss_leave+0xb90/0x1900 [mac80211] [ 100.490590] [<80081604>] warn_slowpath_common+0xa0/0xd0 [ 100.495922] [<801a359c>] dump_stack+0x14/0x28 [ 100.500350] [<80071a00>] show_stack+0x50/0x84 [ 100.504784] [<80081604>] warn_slowpath_common+0xa0/0xd0 [ 100.510106] [<87024c60>] ath9k_calculate_summary_state+0x250/0x60c [ath9k] [ 100.517105] [<800816b8>] warn_slowpath_null+0x18/0x24 [ 100.522256] [<87024c60>] ath9k_calculate_summary_state+0x250/0x60c [ath9k] [ 100.529273] [<87025418>] ath9k_set_txpower+0x148/0x498 [ath9k] [ 100.535302] [<871d2c64>] cleanup_module+0xa74/0xd4c [mac80211] [ 100.541237] [<801ef308>] serial8250_console_putchar+0x0/0x44 [ 100.547042] [<800a5d18>] wake_up_klogd+0x54/0x68 [ 100.551730] [<800a6650>] vprintk_emit+0x404/0x43c [ 100.556623] [<871b9db8>] ieee80211_sta_rx_notify+0x258/0x32c [mac80211] [ 100.563475] [<871ba6a4>] ieee80211_sta_rx_queued_mgmt+0x63c/0x734 [mac80211] [ 100.570693] [<871aa49c>] ieee80211_tx_prepare_skb+0x210/0x230 [mac80211] [ 100.577609] [<800af5d4>] mod_timer+0x15c/0x190 [ 100.582220] [<871ba8b8>] ieee80211_sta_work+0xfc/0xe1c [mac80211] [ 100.588539] [<871940b4>] ieee80211_ibss_leave+0xeec/0x1900 [mac80211] [ 100.595122] [<8009ec84>] dequeue_task_fair+0x44/0x130 [ 100.600281] [<80092a34>] process_one_work+0x1f8/0x334 [ 100.605454] [<80093830>] worker_thread+0x2b4/0x408 [ 100.610317] [<8009357c>] worker_thread+0x0/0x408 [ 100.615019] [<8009357c>] worker_thread+0x0/0x408 [ 100.619705] [<80097b68>] kthread+0xdc/0xe8 [ 100.623886] [<80097a8c>] kthread+0x0/0xe8 [ 100.627961] [<80060878>] ret_from_kernel_thread+0x14/0x1c [ 100.633448] [ 100.634956] ---[ end trace aafbe57e9ae6862f ]--- Fixes: cfda2d8e2314 ("ath9k: Fix beacon configuration for addition/removal of interfaces") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* / tree-wide: replace config_enabled() with IS_ENABLED()Masahiro Yamada2016-08-04
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The use of config_enabled() against config options is ambiguous. In practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the author might have used it for the meaning of IS_ENABLED(). Using IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention clearer. This commit replaces config_enabled() with IS_ENABLED() where possible. This commit is only touching bool config options. I noticed two cases where config_enabled() is used against a tristate option: - config_enabled(CONFIG_HWMON) [ drivers/net/wireless/ath/ath10k/thermal.c ] - config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE) [ drivers/gpu/drm/gma500/opregion.c ] I did not touch them because they should be converted to IS_BUILTIN() in order to keep the logic, but I was not sure it was the authors' intention. Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: Stas Sergeev <stsp@list.ru> Cc: Matt Redfearn <matt.redfearn@imgtec.com> Cc: Joshua Kinard <kumba@gentoo.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Borislav Petkov <bp@suse.de> Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: "Dmitry V. Levin" <ldv@altlinux.org> Cc: yu-cheng yu <yu-cheng.yu@intel.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: Brian Gerst <brgerst@gmail.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Will Drewry <wad@chromium.org> Cc: Nikolay Martynov <mar.kolya@gmail.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com> Cc: Rafal Milecki <zajec5@gmail.com> Cc: James Cowgill <James.Cowgill@imgtec.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Alex Smith <alex.smith@imgtec.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: Qais Yousef <qais.yousef@imgtec.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Mikko Rapeli <mikko.rapeli@iki.fi> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com> Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Ingo Molnar <mingo@redhat.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Roland McGrath <roland@hack.frob.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: Kalle Valo <kvalo@qca.qualcomm.com> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Tony Wu <tung7970@gmail.com> Cc: Huaitong Han <huaitong.han@intel.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Juergen Gross <jgross@suse.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: "David S. Miller" <davem@davemloft.net> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Andrea Gelmini <andrea.gelmini@gelma.net> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Rabin Vincent <rabin@rab.in> Cc: "Maciej W. Rozycki" <macro@imgtec.com> Cc: David Daney <david.daney@cavium.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* ath9k_hw: implement temperature compensation support for AR9003+Felix Fietkau2016-07-19
| | | | | Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* ath9k_hw: get rid of some duplicate code in calibration initFelix Fietkau2016-07-19
| | | | | | | Remove a misleading debug message as well Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* ath9k_hw: simplify ar9003_hw_per_calibrationFelix Fietkau2016-07-19
| | | | | | | Reduce indentation, use a variable to save a few pointer dereferences Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-04-10 09:05:54 -0400