aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/net/ethernet/intel/i40e/i40e.h
Commit message (Collapse)AuthorAge
* i40e: Remove limit of 64 max queues per channelAmritha Nambiar2017-11-22
| | | | | | | | | | | It is safe to remove the upper limit of 64 queues on a channel VSI. The upper bound is determined by the VSI's num_queue_pairs and gets validated when the queue mapping info through mqprio interface is subject to bound checking in the driver. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Enable cloud filters via tc-flowerAmritha Nambiar2017-10-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables tc-flower based hardware offloads. tc flower filter provided by the kernel is configured as driver specific cloud filter. The patch implements functions and admin queue commands needed to support cloud filters in the driver and adds cloud filters to configure these tc-flower filters. The classification function of the filter is to direct matched packets to a traffic class. The hardware traffic class is set based on the the classid reserved in the range :ffe0 - :ffef. Match Dst MAC and route to TC0: prio 1 flower dst_mac 3c:fd:fe:a0:d6:70 skip_sw\ hw_tc 1 Match Dst IPv4,Dst Port and route to TC1: prio 2 flower dst_ip 192.168.3.5/32\ ip_proto udp dst_port 25 skip_sw\ hw_tc 2 Match Dst IPv6,Dst Port and route to TC1: prio 3 flower dst_ip fe8::200:1\ ip_proto udp dst_port 66 skip_sw\ hw_tc 2 Delete tc flower filter: Example: Flow Director Sideband is disabled while configuring cloud filters via tc-flower and until any cloud filter exists. Unsupported matches when cloud filters are added using enhanced big buffer cloud filter mode of underlying switch include: 1. source port and source IP 2. Combined MAC address and IP fields. 3. Not specifying L4 port These filter matches can however be used to redirect traffic to the main VSI (tc 0) which does not require the enhanced big buffer cloud filter support. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com> Signed-off-by: Jingjing Wu <jingjing.wu@intel.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Clean up of cloud filtersAmritha Nambiar2017-10-31
| | | | | | | | | | Introduce the cloud filter data structure and cleanup of cloud filters associated with the device. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Map TCs with the VSI seidsAmritha Nambiar2017-10-31
| | | | | | | | | | | Add mapping of TCs with the seids of the channel VSIs. TC0 will be mapped to the main VSI seid and all other TCs are mapped to the seid of the corresponding channel VSI. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: fix u64 division usageAlan Brady2017-10-17
| | | | | | | | | | | | | | | | Commit 52eb1ff93e98 ("i40e: Add support setting TC max bandwidth rates") and commit 1ea6f21ae530 ("i40e: Refactor VF BW rate limiting") add some needed functionality for TC bandwidth rate limiting. Unfortunately they introduce several usages of unsigned 64-bit division which needs to be handled special by the kernel to support all architectures. Fixes: 52eb1ff93e98 ("i40e: Add support setting TC max bandwidth rates") Fixes: 1ea6f21ae530 ("i40e: Refactor VF BW rate limiting") Signed-off-by: Alan Brady <alan.brady@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Add support setting TC max bandwidth ratesAmritha Nambiar2017-10-13
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch enables setting up maximum Tx rates for the traffic classes in i40e. The maximum rate is offloaded to the hardware through the mqprio framework by specifying the mode option as 'channel' and shaper option as 'bw_rlimit' and is configured for the VSI. Configuring minimum Tx rate limit is not supported in the device. The minimum usable value for Tx rate is 50Mbps. Example: # tc qdisc add dev eth0 root mqprio num_tc 2 map 0 0 0 0 1 1 1 1\ queues 4@0 4@4 hw 1 mode channel shaper bw_rlimit\ max_rate 4Gbit 5Gbit To dump the bandwidth rates: # tc qdisc show dev eth0 qdisc mqprio 804a: root tc 2 map 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 queues:(0:3) (4:7) mode:channel shaper:bw_rlimit max_rate:4Gbit 5Gbit Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Refactor VF BW rate limitingAmritha Nambiar2017-10-13
| | | | | | | | | | This patch refactors the BW rate limiting for Tx traffic on the VF to be reused in the next patch for rate limiting Tx traffic for the VSIs on the PF as well. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Enable 'channel' mode in mqprio for TC configsAmritha Nambiar2017-10-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The i40e driver is modified to enable the new mqprio hardware offload mode and factor the TCs and queue configuration by creating channel VSIs. In this mode, the priority to traffic class mapping and the user specified queue ranges are used to configure the traffic classes by setting the mode option to 'channel'. Example: map 0 0 0 0 1 2 2 3 queues 2@0 2@2 1@4 1@5\ hw 1 mode channel qdisc mqprio 8038: root tc 4 map 0 0 0 0 1 2 2 3 0 0 0 0 0 0 0 0 queues:(0:1) (2:3) (4:4) (5:5) mode:channel shaper:dcb The HW channels created are removed and all the queue configuration is set to default when the qdisc is detached from the root of the device. This patch also disables setting up channels via ethtool (ethtool -L) when the TCs are configured using mqprio scheduler. The patch also limits setting ethtool Rx flow hash indirection (ethtool -X eth0 equal N) to max queues configured via mqprio. The Rx flow hash indirection input through ethtool should be validated so that it is within in the queue range configured via tc/mqprio. The bound checking is achieved by reporting the current rss size to the kernel when queues are configured via mqprio. Example: map 0 0 0 1 0 2 3 0 queues 2@0 4@2 8@6 11@14\ hw 1 mode channel Cannot set RX flow hash configuration: Invalid argument Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Add infrastructure for queue channel supportAmritha Nambiar2017-10-13
| | | | | | | | | | | | | | | | | | | | | This patch sets up the infrastructure for offloading TCs and queue configurations to the hardware by creating HW channels(VSI). A new channel is created for each of the traffic class configuration offloaded via mqprio framework except for the first TC (TC0). TC0 for the main VSI is also reconfigured as per user provided queue parameters. Queue counts that are not power-of-2 are handled by reconfiguring RSS by reprogramming LUTs using the queue count value. This patch also handles configuring the TX rings for the channels, setting up the RX queue map for channel. Also, the channels so created are removed and all the queue configuration is set to default when the qdisc is detached from the root of the device. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Signed-off-by: Kiran Patil <kiran.patil@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Add macro for PF reset bitAmritha Nambiar2017-10-13
| | | | | | | | | | | | Introduce a macro for the bit setting the PF reset flag and update its usages. This makes it easier to use this flag in functions to be introduced in future without encountering checkpatch issues related to alignment and line over 80 characters. Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e/i40evf: always set the CLEARPBA flag when re-enabling interruptsJacob Keller2017-10-09
| | | | | | | | | | | | | | | | | In the past we changed driver behavior to not clear the PBA when re-enabling interrupts. This change was motivated by the flawed belief that clearing the PBA would cause a lost interrupt if a receive interrupt occurred while interrupts were disabled. According to empirical testing this isn't the case. Additionally, the data sheet specifically says that we should set the CLEARPBA bit when re-enabling interrupts in a polling setup. This reverts commit 40d72a509862 ("i40e/i40evf: don't lose interrupts") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: fix flags declarationJacob Keller2017-10-09
| | | | | | | | | | | | | | | Since we don't yet have more than 32 flags, we'll use a u32 for both the hw_features and flag field. Should we gain more flags in the future, we may need to convert to a u64 or separate flags out into two fields. This was overlooked in the previous commit 2781de2134c4 ("i40e/i40evf: organize and re-number feature flags"), where the feature flag was not converted form u64 to u32. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e/i40evf: organize and re-number feature flagsJacob Keller2017-10-06
| | | | | | | | | | | | | | | | | | | | | | | Now that we've reduced the number of flags, organize similar flags together and re-number them accordingly. Since we don't yet have more than 32 flags, we'll use a u32 for both the hw_features and flag field. Should we gain more flags in the future, we may need to convert to a u64 or separate flags out into two fields. One alternative approach considered, but not implemented here, was to use an enumeration for the flag variables, and create a macro I40E_FLAG() which used string concatenation to generate BIT_ULL values. This has the advantage of making the actual bit values compile-time dynamic so that we do not need to worry about matching the order to the bit value. However, this does produce a high level of code churn, and makes it more difficult to read a dumped flags value when debugging. Change-ID: I8653fff69453cd547d6fe98d29dfa9d8710387d1 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Display error message if module does not meet thermal requirementsFilip Sadowski2017-10-06
| | | | | | | | | This patch causes error message to be displayed when NIC detects insertion of module that does not meet thermal requirements. Signed-off-by: Filip Sadowski <filip.sadowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: add private flag to control source pruningMitch Williams2017-10-06
| | | | | | | | | | | | | | | | | | By default, our devices do source pruning, that is, they drop receive packets that have the source MAC matching one of the receive filters. Unfortunately, this breaks ARP monitoring in channel bonding, as the bonding driver expects devices to receive ARPs containing their own source address. Add an ethtool private flag to control this feature. Also, remove the netif_running() check when we process our private flags. It's OK to reset when the device is closed and in most cases we need the reset the apply these changes. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: fix a typo in i40e_pf documentationRami Rosen2017-10-06
| | | | | | | | | This patch fixes a typo in i40e_pf object documentation; num_req_vfs refers to the number of VFs requested for the PF. Signed-off-by: Rami Rosen <rami.rosen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Enable VF to negotiate number of allocated queuesAlan Brady2017-09-29
| | | | | | | | | | | | | | | | | | | | | | | Currently the PF allocates a default number of queues for each VF and cannot be changed. This patch enables the VF to request a different number of queues allocated to it. This patch also adds a new virtchnl op and capability flag to facilitate this negotiation. After the PF receives a request message, it will set a requested number of queues for that VF. Then when the VF resets, its VSI will get a new number of queues allocated to it. This is a best effort request and since we only allocate a guaranteed default number, if the VF tries to ask for more than the guaranteed number, there may not be enough in HW to accommodate it unless other queues for other VFs are freed. It should also be noted decreasing the number queues allocated to a VF to below the default will NOT enable the allocation of more than 32 VFs per PF and will not free queues guaranteed to each VF by default. Signed-off-by: Alan Brady <alan.brady@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: use separate state bit for miscellaneous IRQ setupJacob Keller2017-09-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We currently (mis)use the __I40E_RECOVERY_PENDING bit to determine when we should actually request a new IRQ in i40e_setup_misc_vector(). This led to a design mistake where we open-coded the re-setup of the miscellaneous vector in i40e_resume() instead of using the function provided. If we did not open-code this and instead tried to use the i40e_setup_misc_vector() function, it would lead to never reallocating the IRQ. This would lead to a second i40e_suspend() call failing to free the vector due to a NULL pointer dereference. A future patch is going to re-work how the i40e_suspend() and i40e_resume() flows work to clear all IRQ vectors, which would require us to use i40e_setup_misc_vector() directly. Since during this time the __I40E_RECOVERY_PENDING bit is set, we'll never re-allocate the vector. Rather than leaving the open-coded setup in i40e_resume() lets just fix the problem properly in i40e_setup_misc_vector(). Introduce a new state bit which indicates when the IRQ has been assigned, which will be set when i40e_setup_misc_vector is first called. This ultimately resolves the issue of re-requesting the vector, without overloading the __I40E_RECOVERY_PENDING state. This ensures that the suspend/resume cycle can use the setup function instead of open-coding the re-request during resume. Additionally, since the only callers of i40e_stop_misc_vector also want to free it, move this code directly into the function to avoid duplication. Due to the new functionality, rename it to i40e_free_misc_vector(). This lets us drop the extra calls to free and re-enable the vector during i40e_suspend() and i40e_resume(). We don't need to call i40e_setup_misc_Vector() in i40e_resume() because it gets called by the i40e_rebuild() call. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: remove workaround for Open Firmware MAC addressJacob Keller2017-08-25
| | | | | | | | | | | | | | | | | | | | | | | | | | Since commit b499ffb0a22c ("i40e: Look up MAC address in Open Firmware or IDPROM"), we've had support for obtaining the MAC address form Open Firmware or IDPROM. This code relied on sending the Open Firmware address directly to the device firmware instead of relying on our MAC/VLAN filter list. Thus, a work around was introduced in commit b1b15df59232 ("i40e: Explicitly write platform-specific mac address after PF reset") We refactored the Open Firmware address enablement code in the ill-named commit 41c4c2b50d52 ("i40e: allow look-up of MAC address from Open Firmware or IDPROM") Since this refactor, we no longer even set I40E_FLAG_PF_MAC. Further, we don't need this work around, because we actually store the MAC address as part of the MAC/VLAN filter hash. Thus, we will restore the address correctly upon reset. The refactor above failed to revert the workaround, so do that now. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: separate hw_features from runtime changing flagsJacob Keller2017-08-25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The number of flags found in pf->flags has grown quite large, and there are a lot of different types of flags. Most of the flags are simply hardware features which are enabled on some firmware or some MAC types. Other flags are dynamic run-time flags which enable or disable certain features of the driver. Separate these two types of flags into pf->hw_features and pf->flags. The hw_features list will contain a set of features which are enabled at init time. This will not contain toggles or otherwise dynamically changing features. These flags should not need atomic protections, as they will be set once during init and then be essentially read only. Everything else will remain in the flags variable. These flags may be modified at any time during run time. A future patch may wish to convert these flags into set_bit/clear_bit/test_bit or similar approach to ensure atomic correctness. The I40E_FLAG_MFP_ENABLED flag may be a good fit for hw_features but currently is used by ethtool in the private flags settings, and thus has been left as part of flags. Additionally, I40E_FLAG_DCB_CAPABLE may be a good fit for the hw_features but this patch has not tried to untangle it yet. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Add support for OEM firmware versionFilip Sadowski2017-06-20
| | | | | | | | | | This patch adds support for OEM firmware version. If OEM specific adapter is detected ethtool reports OEM product version in firmware version string instead of etrack id. Signed-off-by: Filip Sadowski <filip.sadowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: genericize the partition bandwidth controlShannon Nelson2017-06-20
| | | | | | | | | | | | | Partition bandwidth control is not in just one form of MFP (multi-function partitioning), so make the code more generic and be sure to nudge the Tx scheduler for all MFP. Copyright updated to 2017. Signed-off-by: Shannon Nelson <shannon.nelson@intel.com> Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: add support for XDP_TX actionBjörn Töpel2017-06-20
| | | | | | | | | | | | This patch adds proper XDP_TX action support. For each Tx ring, an additional XDP Tx ring is allocated and setup. This version does the DMA mapping in the fast-path, which will penalize performance for IOMMU enabled systems. Further, debugfs support is not wired up for the XDP Tx rings. Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: add XDP support for pass and drop actionsBjörn Töpel2017-06-20
| | | | | | | | | This commit adds basic XDP support for i40e derived NICs. All XDP actions will end up in XDP_DROP. Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-06-15
|\ | | | | | | | | | | | | The conflicts were two cases of overlapping changes in batman-adv and the qed driver. Signed-off-by: David S. Miller <davem@davemloft.net>
| * i40e: fix handling of HW ATR evictionJacob Keller2017-06-12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A recent commit to refactor the driver and remove the hw_disabled_flags field accidentally introduced two regressions. First, we overwrote pf->flags which removed various key flags including the MSI-X settings. Additionally, it was intended that we have now two flags, HW_ATR_EVICT_CAPABLE and HW_ATR_EVICT_ENABLED, but this was not done, and we accidentally were mis-using HW_ATR_EVICT_CAPABLE everywhere. This patch adds the missing piece, HW_ATR_EVICT_ENABLED, and safely updates pf->flags instead of overwriting it. Without this patch we will have many problems including disabling MSI-X support, and we'll attempt to use HW ATR eviction on devices which do not support it. Fixes: 47994c119a36 ("i40e: remove hw_disabled_flags in favor of using separate flag bits", 2017-04-19) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | i40e: use new unified virtchnl header fileJesse Brandeburg2017-06-01
| | | | | | | | | | | | | | | | | | | | This patch changes the i40e driver to start using the new virtchnl interface header file, and removes an already existing duplicate of the i40e_virtchnl.h file contained in the i40e directory. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | i40e: check for Tx timestamp timeouts during watchdogJacob Keller2017-05-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The i40e driver has logic to handle only one Tx timestamp at a time, using a state bit lock to avoid multiple requests at once. It may be possible, if incredibly unlikely, that a Tx timestamp event is requested but never completes. Since we use an interrupt scheme to determine when the Tx timestamp occurred we would never clear the state bit in this case. Add an i40e_ptp_tx_hang() function similar to the already existing i40e_ptp_rx_hang() function. This function runs in the watchdog routine and makes sure we eventually recover from this case instead of permanently disabling Tx timestamps. Note: there is no currently known way to cause this without hacking the driver code to force it. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | i40e: use pf data structure directly in i40e_ptp_rx_hangJacob Keller2017-05-31
| | | | | | | | | | | | | | | | | | There's no reason to pass a *vsi pointer if we already have the *pf pointer in the only location where we call this function. Lets update the signature and directly pass the *pf data structure pointer. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* | i40e: add statistic indicating number of skipped Tx timestampsJacob Keller2017-05-31
|/ | | | | | | | | | | | The i40e driver can only handle one Tx timestamp request at a time. This means it is possible for an application timestamp request to be ignored. There is no easy way for an administrator to determine if this occurred. Add a new statistic which tracks this, tx_hwtstamp_skipped. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: remove hw_disabled_flags in favor of using separate flag bitsJacob Keller2017-04-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The hw_disabled_flags field was added as a way of signifying that a feature was automatically or temporarily disabled. However, we actually only use this for FDir features. Replace its use with new _AUTO_DISABLED flags instead. This is more readable, because you aren't setting an *_ENABLED flag to *disable* the feature. Additionally, clean up a few areas where we used these bits. First, we don't really need to set the auto-disable flag for ATR if we're fully disabling the feature via ethtool. Second, we should always clear the auto-disable bits in case they somehow got set when the feature was disabled. However, avoid displaying a message that we've re-enabled the feature. Third, we shouldn't be re-enabling ATR in the SB ntuple add flow, because it might have been disabled due to space constraints. Instead, we should just wait for the fdir_check_and_reenable to be called by the watchdog. Overall, this change allows us to simplify some code by removing an extra field we didn't need, and the result should make it more clear as to what we're actually doing with these flags. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: use DECLARE_BITMAP for state fieldsJacob Keller2017-04-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | Instead of assuming our flags fit within an unsigned long, use DECLARE_BITMAP which will ensure that we always allocate enough space. Additionally, use __I40E_STATE_SIZE__ markers as the last element of the enumeration so that the size of the BITMAP is compile-time assigned rather than programmer-time assigned. This ensures that potential future flag additions do not actually overrun the array. This is especially important as 32bit systems would only have 32bit longs instead of 64bit longs as we generally have assumed in the prior code. This change also removes a dereference of the state fields throughout the code, so it does have a bit of code churn. The conversions were automated using sed replacements with an alternation s/&(vsi->back|vsi|pf)->state/\1->state/ s/&adapter->vsi.state/adapter->vsi.state/ For debugfs, we modify the printing so that we can display chunks of the state value on new lines. This ensures that we can print the entire set of state values. Additionally, we now print them as 08lx to ensure that they display nicely. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: separate PF and VSI state flagsJacob Keller2017-04-30
| | | | | | | | | | | | | | | Avoid using the same named flags for both vsi->state and pf->state. This makes code review easier, as it is more likely that future authors will use the correct state field when checking bits. Previous commits already found issues with at least one check, and possibly others may be incorrect. This reduces confusion as it is more clear what each flag represents, and which flags are valid for which state field. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: rename index to port to avoid confusionJacob Keller2017-04-30
| | | | | | | | | The .index field of i40e_udp_port_config represents the udp port number. Rename this variable to port so that it is more obvious. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: use i40e_stop_rings_no_wait to implement PORT_SUSPENDED stateJacob Keller2017-04-19
| | | | | | | | | | | | | | | | | | | | | This state bit was added as a way for DCB to avoid having to wait for the queues to disable when handling LLDP events. The logic for this was burried deep within stop Tx and stop Rx queue code. First, let's rename it so that it does not appear to only affect Tx when infact it modifies both Tx and Rx flow. Second we can move it up into the i40e_stop_rings() function, and we can simply re-use the i40e_stop_rings_no_wait() so that we don't have to bury the implementation as deep into the call stack. An alternative might be to remove the state bit and instead attempt to shut down everything directly in DCP flow. This, however, is not ideal because it creates yet another separate shutdown routine that we'd have to maintain. In the current implementation any changes will be made to both flows. Change-ID: I68e1ccb901af320862bca395e9c9746f08e8b17c Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: reset all VFs in parallel when rebuilding PFJacob Keller2017-04-19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When there are a lot of active VFs, it can take multiple seconds to finish resetting all of them during certain flows., which can cause some VFs to fail to wait long enough for the reset to occur. The user might see messages like "Never saw reset" or "Reset never finished" and the VF driver will stop functioning properly. The naive solution would be to simply increase the wait timer. We can get much more clever. Notice that i40e_reset_vf is run in a serialized fashion, and includes lots of delays. There are two prominent delays which take most of the time. First, when we begin resetting VFs, we have multiple 10ms delays which accrue because we reset each VF in a serial fashion. These delays accumulate to almost 4 seconds when handling the maximum number of VFs (128). Secondly, there is a massive 50ms delay for each time we disable queues on a VSI. This delay is necessary to allow HW to finish disabling queues before we restore functionality. However, just like with the first case, we are paying the cost for each VF, rather than disabling all VFs and waiting once. Both of these can be fixed, but required some previous refactoring to handle the special case. First, we will need the i40e_vsi_wait_queues_disabled function which was previously DCB specific. Second, we will need to implement our own i40e_vsi_stop_rings_no_wait function which will handle the stopping of rings without the delays. Finally, implement an i40e_reset_all_vfs function, which will first start the reset of all VFs, and pay the wait cost all at once, rather than serially waiting for each VF before we start processing then next one. After the VF has been reset, we'll disable all the VF queues, and then wait for them to disable. Again, we'll organize the flow such that we pay the wait cost only once. Finally, after we've disabled queues we'll go ahead and begin restoring VF functionality. The result is reducing the wait time by a large factor and ensuring that VFs do not timeout when waiting in the VF driver. Change-ID: Ia6e8cf8d98131b78aec89db78afb8d905c9b12be Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Fix support for flow director programming statusAlexander Duyck2017-04-19
| | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes an issue I introduced when I converted the code over to using the length field to determine if a descriptor was done or not. It turns out that we are also processing programming descriptors in the Rx path and need to have these processed even though the length field will be 0 on these packets. What will happen with a programming descriptor is that we will receive a descriptor that has the SPH bit set, and the header length and packet length fields cleared. To account for this we should be checking for the bit for split header being set even though we aren't actually using header split. This bit is set in the length field to indicate if a programming descriptor response is contained in the descriptor. Since we don't support header split we don't need to perform the extra checks of using a fixed value for the entire length field. In addition I am moving the function for checking if a filter is a programming status filter into the i40e_txrx.c file since there is no longer support for FCoE it doesn't make sense to keep this file in i40e.h. Change-ID: I12c359c3dc70adb9d6b92b27324bb2c7f04c1a06 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: clean up historic deprecated flag definitionsJacob Keller2017-04-08
| | | | | | | | | | Since an early commit a few flags have no longer been used. Remove these definitions to reduce code clutter. Change-ID: I3589be4622574e747013cd4dc403e18b039f4965 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: remove I40E_FLAG_NEED_LINK_UPDATEAlice Michael2017-04-08
| | | | | | | | | | The I40E_FLAG_NEED_LINK_UPDATE was never used. Remove the flag definitions. Change-ID: If59d0c6b4af85ca27281f3183c54b055adb439a4 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Simplify i40e_detect_recover_hung_queue logicAlan Brady2017-04-08
| | | | | | | | | | | | | | | | | | | | This patch greatly reduces the unneeded complexity in the i40e_detect_recover_hung_queue code path. The previous implementation set a 'hung bit' which would then get cleared while polling. If the detection routine was called a second time with the bit already set, we would issue a software interrupt. This patch makes it such that if interrupts are disabled and we have pending TX descriptors, we trigger a software interrupt since in, the worst case, queues are already clean and we have an extra interrupt. Additionally this patch removes the workaround for lost interrupts as calling napi_reschedule in this context can cause software interrupts to fire on the wrong CPU. Change-ID: Iae108582a3ceb6229ed1d22e4ed6e69cf97aad8d Signed-off-by: Alan Brady <alan.brady@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Decrease the scope of rtnl lockMaciej Sosin2017-04-08
| | | | | | | | | | | | Previously rtnl lock was held during whole reset procedure that was stopping other PFs running their reset procedures. In the result reset was not handled properly and host reset was the only way to recover. Change-ID: I23c0771c0303caaa7bd64badbf0c667e25142954 Signed-off-by: Maciej Sosin <maciej.sosin@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e/i40evf: Add legacy-rx private flag to allow fallback to old Rx flowAlexander Duyck2017-03-29
| | | | | | | | | | | | | This patch adds a control which will allow us to toggle into and out of the legacy Rx mode. The legacy Rx mode is what we currently do when performing Rx. As I make further changes what should happen is that the driver will fall back to the behavior for Rx as of this patch should the "legacy-rx" flag be set to on. Change-ID: I0342998849bbb31351cce05f6e182c99174e7751 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: remove FDIR_REQUIRES_REINIT driver flagJacob Keller2017-03-29
| | | | | | | | | | | | This flag hasn't been used since commit 1e1be8f622ee ("i40e: ATR policy change to flush the table to clean stale ATR rules"). Lets simplify things and just remove it. Change-ID: I76279d84db8a2fd96f445b96aa413059f9256879 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Clean up handling of private flagsAlexander Duyck2017-03-29
| | | | | | | | | | | | | | | | | | | | | | This patch cleans up and addresses several issues in the way that i40e handles private flags. Previously the code was choosing fixed bits and trying to match them up with strings in a somewhat haphazard way. This resulted in the possibility for adding a new bit and causing a mismatch as the private flags are linear bits starting at 0, and the private flags in the driver were split up over a group specific to the PF and a group that was global. What this change does is define an array of structs used to represent the private flags. Contained within the structs are the bits necessary to know which flags to set and/or clear depending on the state of the bit. By doing this we can add new bits in the future with minimal overhead and avoid creating possible mis-matches should we need to remove a flag based on compile options. Change-ID: Ia3214ab04f0ab2f70354ac0997a135f1d01b0acd Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Drop FCoE code that always evaluates to false or 0Alexander Duyck2017-03-27
| | | | | | | | | | | | | Since FCoE isn't supported by the i40e products there isn't much point in carrying around code that will always evaluate to false. This patch goes through and strips out the code in several spots so that we don't go around carrying variables and/or code that is always going to evaluate to false or 0. Change-ID: I39d1d779c66c638b75525839db2b6208fdc809d7 Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: Drop FCoE code from core driver filesAlexander Duyck2017-03-27
| | | | | | | | | | | | | Looking over the code for FCoE it looks like the Rx path has been broken at least since the last major Rx refactor almost a year ago. It seems like FCoE isn't supported for any of the Fortville/Fortpark hardware so there isn't much point in carrying the code around, especially if it is broken and untested. Change-ID: I892de8fa551cb129ce2361e738ff82ce55fa229e Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: add support for SCTPv4 FDir filtersJacob Keller2017-03-24
| | | | | | | | | | | Enable FDir filters for SCTPv4 packets using the ethtool ntuple interface to enable filters. The ethtool API does not allow masking on the verification tag. Change-Id: I093e88a8143994c7e6f4b7b17a0bd5cf861d18e4 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: implement support for flexible word payloadJacob Keller2017-03-24
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for flexible payloads passed via ethtool user-def field. This support is somewhat limited due to hardware design. The input set can only be programmed once per filter type, and the flexible offset is part of this filter input set. This means that the user cannot program both a regular and a flexible filter at the same time for a given flow type. Additionally, the user may not program two flexible filters of the same flow type with different offsets, although they are allowed to configure different values at that offset location. We support a single flexible word (2byte) value per protocol type, and we handle the FLX_PIT register using a list of flexible entries so that each flow type may be configured separately. Due to hardware implementation, the flexible data is offset from the start of the packet payload, and thus may not be in part of the header data. For this reason, the offset provided by the user defined data is interpreted as a byte offset from the start of the matching payload. Previous implementations have tried to represent the offset as from the start of the frame, but this is not feasible because header sizes may change due to options. Change-Id: 36ed27995e97de63f9aea5ade5778ff038d6f811 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: add parsing of flexible filter fields from userdefJacob Keller2017-03-24
| | | | | | | | | | | | | | | | | | | | | | | | | | Add code to parse the user-def field into a data structure format. This code is intended to allow future extensions of the user-def field by keeping all code that actually reads and writes the field into a single location. This ensures that we do not litter the driver with references to the user-def field and minimizes the amount of bitwise operations we need to do on the data. Add code which parses the lower 32bits into a flexible word and its offset. This will be used in a future patch to enable flexible filters which can match on some arbitrary data in the packet payload. For now, we just return -EOPNOTSUPP when this is used. Add code to fill in the user-def field when reporting the filter back, even though we don't actually implement any user-def fields yet. Additionally, ensure that we mask the extended FLOW_EXT bit from the flow_type now that we will be accepting filters which have the FLOW_EXT bit set (and thus make use of the user-def field). Change-Id: I238845035c179380a347baa8db8223304f5f6dd7 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* i40e: restore default input set for each flow typeJacob Keller2017-03-24
| | | | | | | | | | | | | | | | | | | | | Ensure that the default input set is correctly reprogrammed when cleaning up after disabling flow director support. This ensures that the programmed value will be in a clean state. Although we do not yet have support for SCTPv4 filters, a future patch will add support for this protocol, so we will correctly restore the SCTPv4 input set here as well. Note that strictly speaking the default hardware value for SCTP includes matching the verification tag. However, the ethtool API does not have support for specifying this value, so there is no reason to keep the verification field enabled. This patch is the next step on the way to enabling partial tuple filters which will be implemented in a following patch. Change-Id: Ic22e1c267ae37518bb036aca4a5694681449f283 Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.2 (git 2.25.0) at 2025-08-02 10:19:01 -0400