| Commit message (Collapse) | Author | Age |
|---|
| |\
| |
| |
| |
| | |
Merge Mario's get_vblank_counter fix forward to prevent conflicts with
his followon patch to add precise vblank timestamping.
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Protect both the setup of the pageflip event and the
latching of the new requested displaylist head pointer
by the event lock, so we can't get into a situation
where vc4_atomic_flush latches the new display list via
HVS_WRITE, then immediately gets preempted before queueing
the pageflip event, then the page-flip completes in hw and
the vc4_crtc_handle_page_flip() runs and no-ops due to
lack of a pending pageflip event, then vc4_atomic_flush
continues and only then queues the pageflip event - after
the page flip handling already no-oped. This would cause
flip completion handling only at the next vblank - one
frame too late.
In vc4_crtc_handle_page_flip() check the actual DL head
pointer in SCALER_DISPLACTX against the requested pointer
for page flip to make sure that the flip actually really
completed in the current vblank and doesn't get deferred
to the next one because the DL head pointer was written
a bit too late into SCALER_DISPLISTX, after start of
vblank, and missed the boat. This avoids handling a
pageflip completion too early - one frame too early.
According to Eric, DL head pointer updates which were
written into the HVS DISPLISTX reg get committed to hardware
at the last pixel of active scanout. Our vblank interrupt
handler, as triggered by PV_INT_VFP_START irq, gets to run
earliest at the first pixel of HBLANK at the end of the
last scanline of active scanout, ie. vblank irq handling
runs at least 1 pixel duration after a potential pageflip
completion happened in hardware.
This ordering of events in the hardware, together with the
lock protection and SCALER_DISPLACTX sampling of this patch,
guarantees that pageflip completion handling only runs at
exactly the vblank irq of actual pageflip completion in all
cases.
Background info from Eric about the relative timing of
HVS, PV's and trigger points for interrupts, DL updates:
https://lists.freedesktop.org/archives/dri-devel/2016-May/107510.html
Tested on RPi 2B with hardware timing measurement equipment
and shown to no longer complete flips too early or too late.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Contrary to other flags to DRM_IOCTL_DEF_DRV(), which restrict usage,
the flag for render node is an enabler (the IOCTL can't be used from
render node if it's not present). So DRM_RENDER_ALLOW needs to be
added to all the flags that were previously 0.
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Reviewed-by: Eric Anholt <eric@anholt.net>
Fixes: 0cd3e2747662 ("drm/vc4: Add missing render node support")
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
As per the documentation in drm_crtc.h, atomic_commit should return
-EBUSY if an asynchronous update is requested and there is an earlier
update pending.
v2: Rebase on the s/async/nonblock/ change.
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The async page flip path was missing drm_crtc_vblank_get/put
completely. The sync flip path was missing a vblank put, so async
flips only reported proper pageflip completion events by chance,
and vblank irq's never turned off after a first vsync'ed page flip
until system reboot.
Tested against Raspian kernel 4.4.8 tree on RPi 2B.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Fixes: b501bacc6060 ("drm/vc4: Add support for async pageflips.")
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
get_vblank_counter hooked up to drm_vblank_count() which alway was
non-sensical but didn't hurt in the past. Since Linux 4.4 it
triggers a WARN_ON_ONCE in drm_update_vblank_count on first vblank
irq disable, so fix it by hooking to drm_vblank_no_hw_counter().
Tested against Raspian kernel 4.4.8 tree on RPi 2B.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Fixes: c8b75bca92cb ("drm/vc4: Add KMS support for Raspberry Pi.")
|
| | |
| |
| |
| |
| |
| |
| |
| | |
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
DRM_FORMAT_XBGR8888 and DRM_FORMAT_ABGR8888 are 2 of the native formats
used in Android, so enable them for VC4. There seems to be no logic behind
HVS_PIXEL_ORDER_xxxx naming, but HVS_PIXEL_ORDER_ARGB seems to work
correctly.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
| |/
|
|
|
|
|
|
|
|
|
|
| |
There is redundant code in the clean up exit path when dpi_connector
fails to be allocated. The current code checks if connector is NULL
before destroying it, in fact, connector is NULL at this point so
the check is redundant and can be removed. The final clean up is
that we can remove the goto fail with a simple return and the unused
variable ret.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull drm fixes from Dave Airlie:
- one IMX built-in regression fix
- a set of amdgpu fixes, mostly powerplay and polaris GPU stuff
- a set of i915 fixes all over, many cc'ed to stable.
The i915 batch contain support for DP++ dongle detection, which is
used to fix some regressions in the HDMI color depth area
* tag 'drm-fixes-v4.7-rc1' of git://people.freedesktop.org/~airlied/linux: (44 commits)
drm/amd: add Kconfig dependency for ACP on DRM_AMDGPU
drm/amdgpu: Fix hdmi deep color support.
drm/amdgpu: fix bug in fence driver fini
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/imx: Match imx-ipuv3-crtc components using device node in platform data
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
...
|
| | |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://anongit.freedesktop.org/drm-intel into drm-next
I see the main drm pull got merged, here's the first batch of fixes for
4.7 already. Fixes all around, a large portion cc: stable stuff.
[airlied: the DP++ stuff is a regression fix].
* tag 'drm-intel-next-fixes-2016-05-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Following a GPU hang, we break out of the request loop in order to
unlock the struct_mutex for use by the GPU reset. However, if we retire
all the requests at that moment, we cannot identify the guilty request
after performing the reset.
v2: Not automatically retiring requests forces us to recheck for
available ringspace.
Fixes: f4457ae71fd6 ("drm/i915: Prevent leaking of -EIO from i915_wait_request()")
Testcase: igt/gem_reset_stats/ban-*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463137042-9669-4-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit e075a32f515becef66dc849f5eca47409ccf5473)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Combine the near identical implementations of intel_logical_ring_begin()
and intel_ring_begin() - the only difference is that the logical wait
has to check for a matching ring (which is assumed by legacy).
In the process some debug messages are culled as there were following a
WARN if we hit an actual error.
v2: Updated commentary
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-12-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 987046ad65361a8b038fbf8d76d152237fb7acf1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When we resume the watermark register may contain some BIOS leftovers,
or just the hardware reset values. We should ignore those as the
pipes will be off anyway, and so frobbing around with intermediate
watermarks doesn't make much sense.
In fact I think we should just throw the skip_intermediate_wm flag
out, and instead properly sanitize the "active" watermarks to match
the current plane and pipe states. The actual wm state readout might
also need a bit of work. But for now, let's continue with the
skip_intermediate_wm to keep the fix more minimal.
Fixes this sort of errors on resume
[drm:ilk_validate_pipe_wm] LP0 watermark invalid
[drm:intel_crtc_atomic_check] No valid intermediate pipe watermarks are possible
[drm:intel_display_resume [i915]] *ERROR* Restoring old state failed with -22
and a boatload of subsequent modeset BAT fails on my ILK.
v2:
- Rebase; the SKL atomic WM patches that just landed changed the WM
structure fields in intel_crtc_state slightly. (Matt)
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: ed4a6a7ca853 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463159442-20478-1-git-send-email-matthew.d.roper@intel.com
(cherry picked from commit e3d5457c7caabb77b3f1d0b09c4a63362e9b04d2)
[Jani: rebase on drm-next while cherry-picking]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The default of 0 is 500us of link training, but that's not enough for
some platforms. Decoding this correctly means we're using 2.5ms of
link training on these platforms, which fixes flickering issues
associated with enabling PSR.
v2: Unbotch the math a bit.
v3: Drop debug hunk.
v4: Improve commit message.
Tested-by: Lyude <cpaul@redhat.com>
Cc: Lyude <cpaul@redhat.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95176
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: "Pandiyan, Dhinakaran" <dhinakaran.pandiyan@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: fritsch@kodi.tv
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463590036-17824-2-git-send-email-daniel.vetter@ffwll.ch
(cherry picked from commit 50db139018f9c94376d5f4db94a3bae65fdfac14)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
In BXT DSI there is no regs programmed with few horizontal timings
in Pixels but txbyteclkhs.. So retrieval process adds some
ROUND_UP ERRORS in the process of PIXELS<==>txbyteclkhs.
Actually here for the given adjusted_mode, we are calculating the
value programmed to the port and then back to the horizontal timing
param in pixels. This is the expected value at the end of get_config,
including roundup errors. And if that is same as retrieved value
from port, then retrieved (HW state) adjusted_mode's horizontal
timings are corrected to match with SW state to nullify the errors.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461053894-5058-2-git-send-email-ramalingam.c@intel.com
(cherry picked from commit 042ab0c3c40be1efcaad6b526173b5536fc6c3bf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
When we read out the watermark state from the hardware we're supposed to
transfer that into the active watermarks, but currently we fail to any
part of the active watermarks that isn't explicitly written. Let's clear
it all upfront.
Looks like this has been like this since the beginning, when I added the
readout. No idea why I didn't clear it up.
Cc: Matt Roper <matthew.d.roper@intel.com>
Fixes: 243e6a44b9ca ("drm/i915: Init HSW watermark tracking in intel_modeset_setup_hw_state()")
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463151318-14719-2-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 15606534bf0a65d8a74a90fd57b8712d147dbca6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
SKL DPLLs shouldn't be called DPPLs.
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 2edd6443e3d0 ("drm/i915: Use a table to initilize shared dplls")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462993473-8254-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
(cherry picked from commit d5aab9d40135725cbe81ed5e3af5209382063193)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
With the introduction of a distinct engine->id vs the hardware id, we need
to fix up the value we use for selecting the target engine when signaling
a semaphore. Note that these values can be merged with engine->guc_id.
Fixes: de1add360522c876c25ef2bbbbab1c94bdb509ab
Cc: stable@vger.kernel.org # v4.6
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461932305-14637-3-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 215a7e3210eb208abe634480741e418b5a8bf60c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Set the lane count for HDMI to 4. This will make it easier to
unduplicate CHV phy code.
This also fixes the the soft reset programming for HDMI with CHV. After
commit a8f327fb8464 ("drm/i915: Clean up CHV lane soft reset
programming"), it wouldn't set the right bits for PCS23 since it relied
on a lane count that was never set.
v2: Set lane_count in *_get_config() to please state checker. (0day)
v3: Set lane_count for DDI in DVI mode too. (CI)
v4: Add note about CHV soft lane reset. (Ander)
Fixes: a8f327fb8464 ("drm/i915: Clean up CHV lane soft reset programming")
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461761065-21195-2-git-send-email-ander.conselvan.de.oliveira@intel.com
(cherry picked from commit d4d6279abe9a4a2d52115bad122118db4995df17)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Retriving the horizontal timings from the port registers as part of
get_config().
This fixes a division by zero:
[ 56.916557] divide error: 0000 [#1] PREEMPT SMP
[ 56.921741] Modules linked in: i915(+) drm_kms_helper syscopyarea
sysfillrect sysimgblt fb_sys_fops drm intel_gtt agpgart cf
g80211 rfkill binfmt_misc ax88179_178a kvm_intel kvm irqbypass crc32c_intel
efivars tpm_tis tpm fuse
[ 56.944106] CPU: 3 PID: 1097 Comm: modprobe Not tainted 4.6.0-rc4+ #433
[ 56.951501] Hardware name: Intel Corp. Broxton M/RVP, BIOS
BXT1RVPA.X64.0131.B30.1604142217 04/14/2016
[ 56.961908] task: ffff88007a854d00 ti: ffff88007aea0000 task.ti:
ffff88007aea0000
[ 56.970273] RIP: 0010:[<ffffffffa01235b2>] [<ffffffffa01235b2>]
drm_mode_hsync+0x22/0x40 [drm]
[ 56.980043] RSP: 0018:ffff88007aea3788 EFLAGS: 00010206
[ 56.985982] RAX: 000000000788b600 RBX: ffff880073c22108 RCX:
0000000000000000
[ 56.993957] RDX: 0000000000000000 RSI: ffff88007ab06800 RDI:
ffff880073c22108
[ 57.001935] RBP: ffff88007aea3788 R08: 0000000000000001 R09:
ffff880073c221e8
[ 57.009903] R10: ffff880073c22108 R11: 0000000000000001 R12:
ffff88007a300000
[ 57.017872] R13: ffff880073c22000 R14: ffff880175f78000 R15:
ffff880175f78798
[ 57.025849] FS: 00007f105d3e6700(0000) GS:ffff88017fd80000(0000)
knlGS:0000000000000000
[ 57.034894] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 57.041317] CR2: 00007f4d485101d0 CR3: 000000007a820000 CR4:
00000000003406e0
[ 57.049292] Stack:
[ 57.051539] ffff88007aea37a0 ffffffffa043b632 ffff880175f787c8
ffff88007aea3810
[ 57.059825] ffffffffa043d59e ffff880175f787b0 ffff88007ab68c00
ffff88007aea37f0
[ 57.068128] ffff880073c221e8 ffff880073c22108 ffff880175f78780
ffff880100000000
[ 57.076430] Call Trace:
[ 57.079254] [<ffffffffa043b632>] intel_mode_from_pipe_config+0x82/0xb0
[i915]
[ 57.087405] [<ffffffffa043d59e>] intel_modeset_setup_hw_state+0x55e/0xd60
[i915]
[ 57.095847] [<ffffffffa043ff94>] intel_modeset_init+0x8e4/0x1630 [i915]
[ 57.103415] [<ffffffffa047bcf0>] i915_driver_load+0xbe0/0x1980 [i915]
[ 57.110745] [<ffffffffa0116c19>] drm_dev_register+0xa9/0xc0 [drm]
[ 57.117681] [<ffffffffa011921d>] drm_get_pci_dev+0x8d/0x1e0 [drm]
[ 57.124600] [<ffffffff8195f942>] ? _raw_spin_unlock_irqrestore+0x42/0x70
[ 57.132253] [<ffffffffa03b0384>] i915_pci_probe+0x34/0x50 [i915]
[ 57.139070] [<ffffffff8149c375>] local_pci_probe+0x45/0xa0
[ 57.145303] [<ffffffff8149d300>] ? pci_match_device+0xe0/0x110
[ 57.151924] [<ffffffff8149d6cb>] pci_device_probe+0xdb/0x130
[ 57.158355] [<ffffffff81579b93>] driver_probe_device+0x223/0x440
[ 57.165169] [<ffffffff81579e85>] __driver_attach+0xd5/0x100
[ 57.171500] [<ffffffff81579db0>] ? driver_probe_device+0x440/0x440
[ 57.178510] [<ffffffff81577736>] bus_for_each_dev+0x66/0xa0
[ 57.184841] [<ffffffff815793de>] driver_attach+0x1e/0x20
[ 57.190881] [<ffffffff81578d6e>] bus_add_driver+0x1ee/0x280
[ 57.197212] [<ffffffff8157abc0>] driver_register+0x60/0xe0
[ 57.203447] [<ffffffff8149bc50>] __pci_register_driver+0x60/0x70
[ 57.210285] [<ffffffffa0119450>] drm_pci_init+0xe0/0x110 [drm]
[ 57.216911] [<ffffffff810dcd8d>] ? trace_hardirqs_on+0xd/0x10
[ 57.223434] [<ffffffffa023a000>] ? 0xffffffffa023a000
[ 57.229237] [<ffffffffa023a092>] i915_init+0x92/0x99 [i915]
[ 57.235570] [<ffffffff810003db>] do_one_initcall+0xab/0x1d0
[ 57.241900] [<ffffffff810f9eef>] ? rcu_read_lock_sched_held+0x7f/0x90
[ 57.249205] [<ffffffff81204f18>] ? kmem_cache_alloc_trace+0x248/0x2b0
[ 57.256509] [<ffffffff811a5eee>] ? do_init_module+0x27/0x1d9
[ 57.262934] [<ffffffff811a5f26>] do_init_module+0x5f/0x1d9
[ 57.269167] [<ffffffff8112392f>] load_module+0x20ef/0x27b0
[ 57.275401] [<ffffffff8111f8e0>] ? store_uevent+0x40/0x40
[ 57.281541] [<ffffffff81124243>] SYSC_finit_module+0xc3/0xf0
[ 57.287969] [<ffffffff8112428e>] SyS_finit_module+0xe/0x10
[ 57.294203] [<ffffffff81960069>] entry_SYSCALL_64_fastpath+0x1c/0xac
[ 57.301406] Code: ff 5d c3 66 0f 1f 44 00 00 0f 1f 44 00 00 8b 87 d8 00 00
00 55 48 89 e5 85 c0 75 22 8b 4f 68 85 c9 78 1b 69 47 58 e8 03 00 00 99 <f7> f9
b9 d3 4d 62 10 05 f4 01 00 00 f7 e1 89 d0 c1 e8 06 5d c3
[ 57.322964] RIP [<ffffffffa01235b2>] drm_mode_hsync+0x22/0x40 [drm]
[ 57.330103] RSP <ffff88007aea3788>
[ 57.334276] ---[ end trace d414224cb2e2a4cf ]---
[ 57.339861] modprobe (1097) used greatest stack depth: 12048 bytes left
Fixes: 6f0e7535e7e1 ("drm/i915/BXT: Get pipe conf from the port registers")
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461053894-5058-1-git-send-email-ramalingam.c@intel.com
(cherry picked from commit cefc4e18785123326c5d4d985085e32160fef7f5)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Faced with sporadic machine hangs on gen7, that mimic the issue of
concurrent writes to the same cacheline and seem to start with
commit 9b9ed3093613 (drm/i915: Remove forcewake dance from seqno/irq
barrier on legacy gen6+), let us restore the spinlock around the mmio
read.
Fixes: 9b9ed3093613 (drm/i915: Remove forcewake dance from seqno/irq...)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461744121-27051-1-git-send-email-chris@chris-wilson.co.uk
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
(cherry picked from commit bcbdb6d01150dcc1769ddc9baaaf7f102f27f919)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Move the intel_enable_gtt() call to happen before we touch the GTT
during resume. Right now it's done way too late. Before
commit ebb7c78d358b ("agp/intel-gtt: Only register fake agp driver for gen1")
it was actually done earlier on account of also getting called from
the resume hook of the fake agp driver. With the fake agp driver
no longer getting registered we must move the call up.
The symptoms I've seen on my 830 machine include lowmem corruption,
other kinds of memory corruption, and straight up hung machine during
or just after resume. Not really sure what causes the memory corruption,
but so far I've not seen any with this fix.
I think we shouldn't really need to call this during init, but we have
been doing that so I've decided to keep the call. However moving that
call earlier could be prudent as well. Doing it right after the
intel-gtt probe seems appropriate.
Also tested this on 946gz,elk,ilk and all seemed quite happy with
this change.
v2: Reorder init_hw vs. enable_hw functions (Chris)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: ebb7c78d358b ("agp/intel-gtt: Only register fake agp driver for gen1")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462559755-353-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit ac840ae53573d9f435c88c131f6707a79aecb466)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
DP dual mode type 1 DVI adaptors aren't required to implement any
registers, so it's a bit hard to detect them. The best way would
be to check the state of the CONFIG1 pin, but we have no way to
do that. So as a last resort, check the VBT to see if the HDMI
port is in fact a dual mode capable DP port.
v2: Deal with VBT code reorganization
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Reduce DEVICE_TYPE_DP_DUAL_MODE_BITS a bit
Accept both DP and HDMI dvo_port in VBT as my BSW
at least declare its DP port as HDMI :(
v3: Ignore DEVICE_TYPE_NOT_HDMI_OUTPUT (Shashank)
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa623446 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462362322-31278-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit d61992565bd3cc5b66d74ed2e96df043c2a207e2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
To save a bit of power, let's try to turn off the TMDS output buffers
in DP++ adaptors when we're not driving the port.
v2: Let's not forget DDI, toss in a debug message while at it
v3: Just do the TMDS output control based on adaptor type. With the
helper getting passed the type, we wouldn't actually have to
check at all in the driver, but the check eliminates the debug
output more honest
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b2ccb822d376d1bbbe5d1f9118d1488b25e6bc6d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Try to detect the max TMDS clock limit for the DP++ adaptor (if any)
and take it into account when checking the port clock.
Note that as with the sink (HDMI vs. DVI) TMDS clock limit we'll ignore
the adaptor TMDS clock limit in the modeset path, in case users are
already "overclocking" their TMDS links. One subtle change here is that
we'll have to respect the adaptor TMDS clock limit when we decide whether
to do 12bpc or 8bpc, otherwise we might end up picking 12bpc and
accidentally driving the TMDS link out of spec even when the user chose
a mode that fits wihting the limits at 8bpc. This means you can't
"overclock" your DP++ dongle at 12bpc anymore, but you can continue to
do so at 8bpc.
Note that for simplicity we'll use the I2C access method for all dual
mode adaptors including type 2. Otherwise we'd have to start mixing
DP AUX and HDMI together. In the future we may need to do that if we
come across any board designs that don't hook up the DDC pins to the
DP++ connectors. Such boards would obviously only work with type 2
dual mode adaptors, and not type 1.
v2: Store adaptor type under indel_hdmi->dp_dual_mode
Deal with DRM_DP_DUAL_MODE_UNKNOWN
Pass adaptor type to drm_dp_dual_mode_max_tmds_clock(),
and use it for type1 adaptors as well
Cc: stable@vger.kernel.org
Reported-by: Tore Anderson <tore@fud.no>
Fixes: 7a0baa623446 ("Revert "drm/i915: Disable 12bpc hdmi for now"")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1462216105-20881-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
(cherry picked from commit b1ba124d8e95cca48d33502a4a76b1ed09d213ce)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Add a helper which aids in the identification of DP dual mode
(aka. DP++) adaptors. There are several types of adaptors
specified: type 1 DVI, type 1 HDMI, type 2 DVI, type 2 HDMI
Type 1 adaptors have a max TMDS clock limit of 165MHz, type 2 adaptors
may go as high as 300MHz and they provide a register informing the
source device what the actual limit is. Supposedly also type 1 adaptors
may optionally implement this register. This TMDS clock limit is the
main reason why we need to identify these adaptors.
Type 1 adaptors provide access to their internal registers and the sink
DDC bus through I2C. Type 2 adaptors provide this access both via I2C
and I2C-over-AUX. A type 2 source device may choose to implement either
of these methods. If a source device implements the I2C-over-AUX
method, then the driver will obviously need specific support for such
adaptors since the port is driven like an HDMI port, but DDC
communication happes over the AUX channel.
This helper should be enough to identify the adaptor type (some
type 1 DVI adaptors may be a slight exception) and the maximum TMDS
clock limit. Another feature that may be available is control over
the TMDS output buffers on the adaptor, possibly allowing for some
power saving when the TMDS link is down.
Other user controllable features that may be available in the adaptors
are downstream i2c bus speed control when using i2c-over-aux, and
some control over the CEC pin. I chose not to provide any helper
functions for those since I have no use for them in i915 at this time.
The rest of the registers in the adaptor are mostly just information,
eg. IEEE OUI, hardware and firmware revision, etc.
v2: Pass adaptor type to helper functions to ease driver implementation
Fix a bunch of typoes (Paulo)
Add DRM_DP_DUAL_MODE_UNKNOWN for the case where we don't (yet) know
the type (Paulo)
Reject 0x00 and 0xff DP_DUAL_MODE_MAX_TMDS_CLOCK values (Paulo)
Adjust drm_dp_dual_mode_detect() type2 vs. type1 detection to
ease future LSPCON enabling
Remove the unused DP_DUAL_MODE_LAST_RESERVED define
v3: Fix kernel doc function argument descriptions (Jani)
s/NONE/UNKNOWN/ in drm_dp_dual_mode_detect() docs
Add kernel doc for enum drm_dp_dual_mode_type
Actually build the docs
Fix more typoes
v4: Adjust code indentation of type2 adaptor detection (Shashank)
Add debug messages for failurs cases (Shashank)
v5: EXPORT_SYMBOL(drm_dp_dual_mode_read) (Paulo)
Cc: stable@vger.kernel.org
Cc: Tore Anderson <tore@fud.no>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com> (v4)
Link: http://patchwork.freedesktop.org/patch/msgid/1462542412-25533-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit ede53344dbfd1dd43bfd73eb6af743d37c56a7c3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
| | |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
into drm-next
AMD GPU bugfixes:
- Various powerplay bug fixes
- Add some new polaris pci ids
- misc bug fixes and code cleanups
* 'drm-next-4.7' of git://people.freedesktop.org/~agd5f/linux: (27 commits)
drm/amd: add Kconfig dependency for ACP on DRM_AMDGPU
drm/amdgpu: Fix hdmi deep color support.
drm/amdgpu: fix bug in fence driver fini
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay: fix bugs of checking if dpm is running on Tonga
drm/amdgpu: update Polaris11 golden setting
drm/amdgpu: Add more Polaris 11 PCI IDs
drm/amdgpu: update Polaris10 golden setting
drm/amdgpu: add more Polaris10 DID
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu/cz_dpm: Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/powerplay: use ARRAY_SIZE() to calculate array size.
drm/amdgpu: fix array out of bounds
drm/radeon: fix array out of bounds
drm/amd/powerplay: fix a bug on updating sclk for Tonga
...
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
The DRM_AMD_ACP option doesn't have any dependencies and selects
MFD_CORE, which results in MFD_CORE=y. Since the code is only called
from DRM_AMDGPU, it should depend on it. Adding the dependency results
in MFD_CORE being selected as a module again if amdgpu is also a module.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When porting the hdmi deep color detection code from
radeon-kms to amdgpu-kms apparently some kind of
copy and paste error happened, attaching an else
branch to the wrong if statement.
The result is that hdmi deep color mode is always
disabled, regardless of gpu and display capabilities and
user wishes, as the code mistakenly thinks that the display
doesn't provide the required max_tmds_clock limit and falls
back to 8 bpc.
This patch fixes deep color support, as tested on a
R9 380 Tonga Pro + suitable display, and should be
backported to all kernels with amdgpu-kms support.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Using wrong counter for walking fences. Fixes
a crash when unloading the driver.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Fixes OD failures on Tonga.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove unused variable 'ret', and directly return 0.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove unused variable 'ret', and directly return 0.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove unused variable 'ret', and directly return 0.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove unused variable 'ret' from functions where it
was not used anyway, and directly return 0.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Remove unused variable 'ret', and directly return 0.
Reviewed-by: Junwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
It is preferred to use ARRAY_SIZE() for size calculation, instead
using sizeof(array)/sizeof(*array). It makes the code more readable.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When the initial value of i is greater than zero,
it may cause endless loop, resulting in array out
of bounds, fix it.
This is a port of the radeon fix to amdgpu.
Signed-off-by: tom will <os@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
When the initial value of i is greater than zero,
it may cause endless loop, resulting in array out
of bounds, fix it.
Signed-off-by: tom will <os@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Update sclk smc table rather than mclk smc table for sclk updates.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
| | | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Update sclk smc table rather than mclk smc table for sclk updates.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Huang <JinHuiEric.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
