aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/gpio
Commit message (Collapse)AuthorAge
...
| * | gpio: zynq: Fix the error pathShubhrajyoti Datta2016-04-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | pm_runtime_disable is called only in remove it is missed out in the error path. Fix the same. Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: Loongson1: add Loongson1 GPIO driverKelvin Cheung2016-04-09
| | | | | | | | | | | | | | | | | | | | | This patch adds GPIO driver for Loongson1B. Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: tps6586x: make explicitly non-modularPaul Gortmaker2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_TPS6586X drivers/gpio/Kconfig: bool "TPS6586X GPIO" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init was not in use by this code, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: tps65910: make explicitly non-modularPaul Gortmaker2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_TPS65910 drivers/gpio/Kconfig: bool "TPS65910 GPIO" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init was not in use by this code, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Graeme Gregory <gg@slimlogic.co.uk> Cc: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: palmas: make explicitly non-modularPaul Gortmaker2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_PALMAS drivers/gpio/Kconfig: bool "TI PALMAS series PMICs GPIO" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init was not in use by this code, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: sx150x: make explicitly non-modularPaul Gortmaker2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_SX150X drivers/gpio/Kconfig: bool "Semtech SX150x I2C GPIO expander" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init was not in use by this code, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information was (or is now) contained at the top of the file in the comments. Cc: Gregory Bean <gbean@codeaurora.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: tc3589x: make explicitly non-modularPaul Gortmaker2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_TC3589X drivers/gpio/Kconfig: bool "TC3589X GPIOs" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init was not in use by this code, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Rabin Vincent <rabin.vincent@stericsson.com> Cc: Hanumath Prasad <hanumath.prasad@stericsson.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: rc5t583: make explicitly non-modularPaul Gortmaker2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_RC5T583 drivers/gpio/Kconfig: bool "RICOH RC5T583 GPIO" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_init was not in use by this code, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: tc3589x: implement open drain/source callbackLinus Walleij2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This makes use of the new .set_single_ended() callback to set the GPIO line as open drain/open source using hardware. The TC3589x can do this by either disabling the N-MOS transistor (open drain) or the P-MOS transistor (open source) of the output driver stage, in the first case making the signal drive actively low and high impedance as "high" and in the second case actively high and high impedance, which is as close to native open drain support as we come. Cc: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: tc3589x: use BIT() macroLinus Walleij2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This switch to use BIT(n) instead of (1 << n) which is less to the point. Most GPIO drivers do this to avoid mistakes. Also switch from using <linux/gpio.h> to the apropriate <linux/gpio/driver.h> include. Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: support native single-ended hardware driversLinus Walleij2016-04-05
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some GPIO controllers has a special hardware bit we can flip to support open drain / source. This means that on these hardwares we do not need to emulate OD/OS by setting the line to input instead of actively driving it high/low. Add an optional vtable callback to the driver set_single_ended() so that driver can implement this in hardware if they have it. We may need a pinctrl_gpio_set_config() call at some point to propagate this down to a backing pin control device on systems with split GPIO/pin control. Reported-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: tpic2810: Make sure cached buffer has consistent status with h/w statusAxel Lin2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | i2c_smbus_write_byte_data() can fail. To ensure the cached buffer has consistent status with h/w status, don't update the cached gpio->buffer if write fails. Also refactor the code a bit by adding a tpic2810_set_mask_bits() helper and use it to simplify the code. Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: zx: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: config GPIO_ZX bool "ZTE ZX GPIO support" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information was (or is now) contained at the top of the file in the comments. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Jun Nie <jun.nie@linaro.org> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: xgene: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_XGENE drivers/gpio/Kconfig: bool "APM X-Gene GPIO controller support" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Feng Kan <fkan@apm.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: sta2x11: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_STA2X11 drivers/gpio/Kconfig: bool "STA2x11/ConneXt GPIO support" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity, so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: pl061: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig for this driver is currently: config GPIO_PL061 bool "PrimeCell PL061 GPIO support" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity, so that when reading the driver there is no doubt it is builtin-only. Since module_init translates to device_initcall in the non-modular case, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information was (or is now) contained at the top of the file in the comments. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org Acked-by: Baruch Siach <baruch@tkos.co.il> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mvebu: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_MVEBU drivers/gpio/Kconfig: def_bool y ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: moxart: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_MOXART drivers/gpio/Kconfig: bool "MOXART GPIO support" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modular references so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. We don't replace module.h with init.h since the file already has that. Cc: Jonas Jensen <jonas.jensen@gmail.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mc9s08dz60: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: drivers/gpio/Kconfig:config GPIO_MC9S08DZ60 drivers/gpio/Kconfig: bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions" ...meaning that it currently is not being built as a module by anyone. Lets remove the modular code that is essentially orphaned, so that when reading the driver there is no doubt it is builtin-only. Since module_i2c_driver() uses the same init level priority as builtin_i2c_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Wu Guoxing <b39297@freescale.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mb86s7x: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig for this driver is currently: config GPIO_MB86S7X bool "GPIO support for Fujitsu MB86S7x Platforms" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity, so that when reading the driver there is no doubt it is builtin-only. Since module_init translates to device_initcall in the non-modular case, the init ordering remains unchanged with this commit. We also delete the MODULE_LICENSE tag etc. since all that information is already contained at the top of the file in the comments. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: bcm-kona: make explicitly non-modularPaul Gortmaker2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Kconfig currently controlling compilation of this code is: config GPIO_BCM_KONA bool "Broadcom Kona GPIO" ...meaning that it currently is not being built as a module by anyone. Lets remove the couple traces of modularity so that when reading the driver there is no doubt it is builtin-only. Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information was (or is now) contained at the top of the file in the comments. Cc: Ray Jui <rjui@broadcom.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: linux-gpio@vger.kernel.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: gpio-it87: Add support for IT8620 and IT8628Martin Blumenstingl2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | These chips seem to have a 9th GPIO block (thus supporting 72 GPIOs) which is configured through SuperIO register 0xd2 (output enable) and 0xd3 (simple I/O). This is also the reason why io_size is larger than on IT8728 / IT8732. Unfortunately I don't have hardware to test this 9th GPIO block. I am also not sure about not configuring the Simple I/O registers as the hardware I have only uses GPIO block 8. Reading back the values of 0xc0-0xc7 (as configured by the BIOS/EFI on my board) shows that all have 0xff set. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: xlp: Add GPIO driver support for Broadcom Vulcan ARM64Kamlakant Patel2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | - Add GPIO support for Broadcom Vulcan ARM64. - Add depends on ARCH_VULCAN to Kconfig to enable gpio controller driver for Broadcom Vulcan ARM64 SoCs. Signed-off-by: Kamlakant Patel <kamlakant.patel@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mcp23s08: Add support for level triggered interruptsAlexander Stein2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The interrupt for the corresponding pin is configured to trigger when the pin state changes compared to a preconfigured state (Bit set in INTCON). This state is set by setting/clearing the bit in DEFVAL. In the interrupt handler we need also to check if the bit in INTCON is set for level triggered interrupts. Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: 74x164: add dt support for nxp's 74x594Nicolas Saenz Julienne2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | The chip is also an 8 bit shift register which works out of the box as a GPO expander with this patch Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: xgene-sb: Use irq_domain_free_irqs_common()Axel Lin2016-03-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current code calls irq_domain_alloc_irqs_parent() in .alloc, so it should call irq_domain_free_irqs_parent() accordingly in .free. Fix it by switching to use irq_domain_free_irqs_common() instead. Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: amdpt: Add a new ACPI HIDYD Tseng2016-03-30
| | | | | | | | | | | | | | | | | | | | | This patch adds a new ACPI HID, AMDIF030, in the pt_gpio_acpi_match. Signed-off-by: YD Tseng<Yd_Tseng@asmedia.com.tw> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: octeon: Constify octeon_gpio_match tableAxel Lin2016-03-30
| | | | | | | | | | | | | | | Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: octeon: Convert to use devm_ioremap_resourceAxel Lin2016-03-30
| | | | | | | | | | | | | | | Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: amdpt: Convert to use gpio-genericAxel Lin2016-03-30
| | | | | | | | | | | | | | | | | | | | | | | | Use gpio-generic to simplify this driver. Signed-off-by: Axel Lin <axel.lin@ingics.com> Tested-by: YD Tseng <Yd_Tseng@asmedia.com.tw> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mcp23s08: delete req/rel_resource callbacksLinus Walleij2016-03-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | When using the GPIOLIB_IRQCHIP the gpiolib provides a straight-forward implementation of request/release resources, rely on that instead. Cc: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mcp23s08: switch to use gpiolib irqchip helpersPhil Reid2016-03-30
| | | | | | | | | | | | | | | | | | | | | | | | This switches the mcp23s08 driver to use the gpiolib irqchip helpers. Signed-off-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: 74x164: Implement gpiochip.set_multiple()Geert Uytterhoeven2016-03-30
| | | | | | | | | | | | | | | | | | | | | | | | This allows to set multiple outputs using a single SPI transfer. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: rcar: Implement gpiochip.set_multiple()Geert Uytterhoeven2016-03-30
| | | | | | | | | | | | | | | | | | | | | This allows to set multiple outputs using a single register write. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: mb86s7x: Remove redundant platform_set_drvdata() callAxel Lin2016-03-30
| | | | | | | | | | | | | | | | | | | | | Set it once is enough, so remove the second platform_set_drvdata() call. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
| * | gpio: menz127: Drop *mdev field from struct men_z127_gpioAxel Lin2016-03-30
| | | | | | | | | | | | | | | | | | | | | No need to store *medv in struct men_z127_gpio. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | | gpiolib-acpi: Duplicate con_id string when adding it to the crs lookup listVille Syrjälä2016-04-30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Calling gpiod_get() from a module and then unloading the module leads to an oops due to acpi_can_fallback_to_crs() storing the pointer to the passed 'con_id' string onto acpi_crs_lookup_list. The next guy to come along will then try to access the string but the memory may now be gone with the module. Make a copy of the passed string instead, and store the copy on the list. BUG: unable to handle kernel paging request at ffffffffa03e7855 IP: [<ffffffff81338322>] strcmp+0x12/0x30 PGD 2a07067 PUD 2a08063 PMD 74720067 PTE 0 Oops: 0000 [#1] PREEMPT SMP Modules linked in: i915(+) drm_kms_helper drm intel_gtt snd_hda_codec snd_hda_core i2c_algo_bit syscopya rea sysfillrect sysimgblt fb_sys_fops agpgart snd_soc_sst_bytcr_rt5640 coretemp hwmon intel_rapl intel_soc_dts_thermal punit_atom_debug snd_soc_rt5640 snd_soc_rl6231 serio snd_intel_sst_acpi snd_intel_sst_core video snd_soc_sst_mfld_platf orm snd_soc_sst_match backlight int3402_thermal processor_thermal_device int3403_thermal int3400_thermal acpi_thermal_r el snd_soc_core intel_soc_dts_iosf int340x_thermal_zone snd_compress i2c_hid hid snd_pcm snd_timer snd soundcore evdev sch_fq_codel efivarfs ipv6 autofs4 [last unloaded: drm] CPU: 2 PID: 3064 Comm: modprobe Tainted: G U W 4.6.0-rc3-ffrd-ipvr+ #302 Hardware name: Intel Corp. VALLEYVIEW C0 PLATFORM/BYT-T FFD8, BIOS BLAKFF81.X64.0088.R10.1403240443 FFD8 _X64_R_2014_13_1_00 03/24/2014 task: ffff8800701cd200 ti: ffff880070034000 task.ti: ffff880070034000 RIP: 0010:[<ffffffff81338322>] [<ffffffff81338322>] strcmp+0x12/0x30 RSP: 0000:ffff880070037748 EFLAGS: 00010286 RAX: 0000000080000000 RBX: ffff88007a342800 RCX: 0000000000000006 RDX: 0000000000000006 RSI: ffffffffa054f856 RDI: ffffffffa03e7856 RBP: ffff880070037748 R08: 0000000000000000 R09: 0000000000000001 R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffa054f855 R13: ffff88007281cae0 R14: 0000000000000010 R15: ffffffffffffffea FS: 00007faa51447700(0000) GS:ffff880079300000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffa03e7855 CR3: 0000000041eba000 CR4: 00000000001006e0 Stack: ffff880070037770 ffffffff8136ad28 ffffffffa054f855 0000000000000000 ffff88007a0a2098 ffff8800700377e8 ffffffff8136852e ffff88007a342800 00000007700377a0 ffff8800700377a0 ffffffff81412442 70672d6c656e6170 Call Trace: [<ffffffff8136ad28>] acpi_can_fallback_to_crs+0x88/0x100 [<ffffffff8136852e>] gpiod_get_index+0x25e/0x310 [<ffffffff81412442>] ? mipi_dsi_attach+0x22/0x30 [<ffffffff813685f2>] gpiod_get+0x12/0x20 [<ffffffffa04fcf41>] intel_dsi_init+0x421/0x480 [i915] [<ffffffffa04d3783>] intel_modeset_init+0x853/0x16b0 [i915] [<ffffffffa0504864>] ? intel_setup_gmbus+0x214/0x260 [i915] [<ffffffffa0510158>] i915_driver_load+0xdc8/0x19b0 [i915] [<ffffffff8160fb53>] ? _raw_spin_unlock_irqrestore+0x43/0x70 [<ffffffffa026b13b>] drm_dev_register+0xab/0xc0 [drm] [<ffffffffa026d7b3>] drm_get_pci_dev+0x93/0x1f0 [drm] [<ffffffff8160fb53>] ? _raw_spin_unlock_irqrestore+0x43/0x70 [<ffffffffa043f1f4>] i915_pci_probe+0x34/0x50 [i915] [<ffffffff81379751>] pci_device_probe+0x91/0x100 [<ffffffff8141a75a>] driver_probe_device+0x20a/0x2d0 [<ffffffff8141a8be>] __driver_attach+0x9e/0xb0 [<ffffffff8141a820>] ? driver_probe_device+0x2d0/0x2d0 [<ffffffff81418439>] bus_for_each_dev+0x69/0xa0 [<ffffffff8141a04e>] driver_attach+0x1e/0x20 [<ffffffff81419c20>] bus_add_driver+0x1c0/0x240 [<ffffffff8141b6d0>] driver_register+0x60/0xe0 [<ffffffff81377d20>] __pci_register_driver+0x60/0x70 [<ffffffffa026d9f4>] drm_pci_init+0xe4/0x110 [drm] [<ffffffff810ce04e>] ? trace_hardirqs_on+0xe/0x10 [<ffffffffa02f1000>] ? 0xffffffffa02f1000 [<ffffffffa02f1094>] i915_init+0x94/0x9b [i915] [<ffffffff810003bb>] do_one_initcall+0x8b/0x1c0 [<ffffffff810eb616>] ? rcu_read_lock_sched_held+0x86/0x90 [<ffffffff811de6d6>] ? kmem_cache_alloc_trace+0x1f6/0x270 [<ffffffff81183826>] do_init_module+0x60/0x1dc [<ffffffff81115a8d>] load_module+0x1d0d/0x2390 [<ffffffff811120b0>] ? __symbol_put+0x70/0x70 [<ffffffff811f41b2>] ? kernel_read_file+0x92/0x120 [<ffffffff811162f4>] SYSC_finit_module+0xa4/0xb0 [<ffffffff8111631e>] SyS_finit_module+0xe/0x10 [<ffffffff81001ff3>] do_syscall_64+0x63/0x350 [<ffffffff816103da>] entry_SYSCALL64_slow_path+0x25/0x25 Code: f7 48 8d 76 01 48 8d 52 01 0f b6 4e ff 84 c9 88 4a ff 75 ed 5d c3 0f 1f 00 55 48 89 e5 eb 04 84 c0 74 18 48 8d 7f 01 48 8d 76 01 <0f> b6 47 ff 3a 46 ff 74 eb 19 c0 83 c8 01 5d c3 31 c0 5d c3 66 RIP [<ffffffff81338322>] strcmp+0x12/0x30 RSP <ffff880070037748> CR2: ffffffffa03e7855 v2: Make the copied con_id const Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: stable@vger.kernel.org Fixes: 10cf4899f8af ("gpiolib: tighten up ACPI legacy gpio lookups") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | | Revert "gpio: rcar: Fine-grained Runtime PM support"Linus Walleij2016-04-12
| | | | | | | | | | | | This reverts commit 65194cb174b873448b208eb6e04ecb72237af76e.
* | | Revert "gpio: rcar: Add Runtime PM handling for interrupts"Linus Walleij2016-04-12
| |/ |/| | | | | This reverts commit b26a719bdba9aa926ceaadecc66e07623d2b8a53.
* | gpio: pca953x: Use correct u16 value for register word writeYong Li2016-04-08
| | | | | | | | | | | | | | | | | | | | | | The current implementation only uses the first byte in val, the second byte is always 0. Change it to use cpu_to_le16 to write the two bytes into the register Cc: stable@vger.kernel.org Signed-off-by: Yong Li <sdliyong@gmail.com> Reviewed-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpiolib: Defer gpio device setup until after gpiolib initializationGuenter Roeck2016-04-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Since commit ff2b13592299 ("gpio: make the gpiochip a real device"), attempts to add a gpio chip prior to gpiolib initialization cause the system to crash. This happens because gpio_bus_type has not been registered yet. Defer creating gpio devices until after gpiolib has been initialized to fix the problem. Cc: Greg Ungerer <gerg@uclinux.org> Cc: Alexandre Courbot <gnurou@gmail.com> Fixes: ff2b13592299 ("gpio: make the gpiochip a real device") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpiolib: Do not use devm functions when registering gpio chipGuenter Roeck2016-04-08
| | | | | | | | | | | | | | | | | | | | | | It is possible that a gpio chip is registered before the gpiolib initialization code has run. This means we can not use devm_ functions to allocate memory at that time. Do it the old fashioned way. Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Greg Ungerer <gerg@uclinux.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpio: pxa: fix legacy non pinctrl aware buildsRobert Jarzmik2016-04-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In legacy pxa builds, ie. non device-tree and platform-data only builds, pinctrl is not yet available. As a consequence, the pinctrl gpio direction change function is a stub, returning always success. In the current state, the gpio driver direction function believes the pinctrl direction change was successful, and exits without actually changing the gpio direction. This patch changes the logic : - if the pinctrl direction function fails, gpio direction will report that failure - if the pinctrl direction function succeeds, gpio direction is changed by the gpio driver anyway. This is sub optimal in the pinctrl aware case, as the gpio direction will be changed twice: once by pinctrl function and another time by the gpio direction function. Yet it should be acceptable in this form, as this is functional for all pxa platforms (device-tree and platform-data), and moreover changing a gpio direction is very very seldom, usually in machine initialization, seldom in drivers probe, and an exception for ac97 reset bug. Fixes: a770d946371e ("gpio: pxa: add pin control gpio direction and request") Reported-by: Guenter Roeck <guenter@roeck-us.net> Tested-by: Guenter Roeck <guenter@roeck-us.net> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpio / ACPI: ignore GpioInt() GPIOs when requesting GPIO_OUT_*Dmitry Torokhov2016-04-08
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When firmware does not use _DSD properties that allow properly name GPIO resources, the kernel falls back on parsing _CRS resources, and will return entries described as GpioInt() as general purpose GPIOs even though they are meant to be used simply as interrupt sources for the device: Device (ETSA) { Name (_HID, "ELAN0001") ... Method(_CRS, 0x0, NotSerialized) { Name(BUF0,ResourceTemplate () { I2CSerialBus( 0x10, /* SlaveAddress */ ControllerInitiated, /* SlaveMode */ 400000, /* ConnectionSpeed */ AddressingMode7Bit, /* AddressingMode */ "\\_SB.I2C1", /* ResourceSource */ ) GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone,, "\\_SB.GPSW") { BOARD_TOUCH_GPIO_INDEX } } ) Return (BUF0) } ... } This gives troubles with drivers such as Elan Touchscreen driver (elants_i2c) that uses devm_gpiod_get to look up "reset" GPIO line and decide whether the driver is responsible for powering up and resetting the device, or firmware is. In the above case the lookup succeeds, we map GPIO as output and later fail to request client->irq interrupt that is mapped to the same GPIO. Let's ignore resources described as GpioInt() while parsing _CRS when requesting output GPIOs (but allow them when requesting GPIOD_ASIS or GPIOD_IN as some drivers, such as i2c-hid, do request GPIO as input and then map it to interrupt with gpiod_to_irq). Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Dmitry Torokhov <dtor@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpio: xgene: Prevent NULL pointer dereferenceAxel Lin2016-03-30
| | | | | | | | | | | | | | | | platform_get_resource() can return NULL, thus add NULL test to prevent NULL pointer dereference. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpio: menz127: Drop lock field from struct men_z127_gpioAxel Lin2016-03-30
|/ | | | | | | | | | Current code uses a uninitialized spin lock. bgpio_init() already initialized a spin lock, so let's switch to use &gc->bgpio_lock instead and remove the lock from struct men_z127_gpio. Fixes: f436bc2726c6 "gpio: add driver for MEN 16Z127 GPIO controller" Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Merge tag 'mfd-for-linus-4.6' of ↵Linus Torvalds2016-03-18
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd Pull MFD updates from Lee Jones: "New Drivers: - Freescale Touch Screen ADC - X-Powers AXP PMIC with RSB - TI TPS65086 Power Management IC (PMIC) New Device Support: - Supply device PCI IDs for Intel Broxton Fix-ups: - Move to clkdev_create() API; intel_quark_i2c_gpio - Complete re-write of TI's TPS65912 Power Management IC (PMIC) - Remove unnecessary function argument; axp20x - Separate out bus related code; axp20x - Coding Style changes; axp20x - Allow more drivers to be compiled as modules - Work around false positive 'used uninitialised' warning; db8500-prcmu Bug Fixes: - Remove do_div(); fsl-imx25-gcq - Fix driver init when built-in; tps65010 - Fix clock-unregister leak; intel-lpss" * tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits) mfd: intel-lpss: Pass I2C configuration via properties on BXT mfd: imx6sx: Add PCIe register definitions for iomuxc gpr mfd: ipaq-micro: Use __maybe_unused to hide pm functions mfd: max77686: Add max77802 to I2C device ID table mfd: max77686: Export OF module alias information mfd: max77686: Allow driver to be built as a module mfd: stmpe: Add the proper PWM resources mfd: tps65090: Set regmap config reg counts properly mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled mfd: as3711: Set regmap config reg counts properly mfd: rc5t583: Set regmap config reg counts properly gpio: tps65086: Add GPO driver for the TPS65086 PMIC mfd: mt6397: Add platform device ID table mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists mfd: mt6397: Add MT6323 support to MT6397 driver mfd: mt6397: Add support for different Slave types mfd: mt6397: int_con and int_status may vary in location dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists mfd: Add documentation for ACT8945A DT bindings ...
| * gpio: tps65086: Add GPO driver for the TPS65086 PMICAndrew F. Davis2016-03-16
| | | | | | | | | | | | | | | | | | | | | | Add support for the TPS65086 PMIC GPOs. TPS65086 has four configurable GPOs that can be used for several purposes. These are output only. Signed-off-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
* | gpio: mcp23s08: Fix clearing of interrupt.Phil Reid2016-03-16
| | | | | | | | | | | | | | | | | | The mcp23s18 is configurable on clearing the interrupt on either reading INTCAP or GPIO. Since driver reads INTCAP in IRQ and not the GPIO reg need to set control byte for this mode. Signed-off-by: Phil Reid <preid@electromag.com.au> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* | gpiolib: Fix comment referring to gpio_*() in gpiod_*()Geert Uytterhoeven2016-03-16
| | | | | | | | | | | | Fixes: 79a9becda8940deb ("gpiolib: export descriptor-based GPIO interface") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.2 (git 2.25.0) at 2025-02-14 02:03:09 -0500