| Commit message (Collapse) | Author | Age |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Bindings for "fixed-regulator" only explicitly support "gpio" property,
not "gpios". Fix by correcting the property name.
The enet PHYs on imx6sx-sdb needs to be explicitly reset after a power
cycle, this can be handled by the phy-reset-gpios property. Sadly this
is not handled on suspend: the fec driver turns phy-supply off but
doesn't assert phy-reset-gpios again on resume.
Since additional phy-level work is required to support powering off the
phy in suspend fix the problem by just marking the regulator as
"boot-on" "always-on" so that it's never turned off. This behavior is
equivalent to older releases.
Keep the phy-reset-gpios property on fec anyway because it is a correct
description of board design.
This issue was exposed by commit efdfeb079cc3 ("regulator: fixed:
Convert to use GPIO descriptor only") which causes the "gpios" property
to also be parsed. Before that commit the "gpios" property had no
effect, PHY reset was only handled in the the bootloader.
This fixes linux-next boot failures previously reported here:
https://lore.kernel.org/patchwork/patch/982437/#1177900
https://lore.kernel.org/patchwork/patch/994091/#1178304
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A quoted label reference doesn't expand to the node path and is taken as
a literal string. Dropping the quotes can fix this unless the baudrate
string is appended in which case we have to use the alias.
At least on VF610, the problem was masked by setting the console in
bootargs. Use the alias syntax with baudrate parameter so we can drop
setting the console in bootargs.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
|
|
|
|
|
| |
Fix the type of compatible string "fs,imx6sll-i2c" which should be
"fsl,imx6sll-i2c".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
|
|
|
|
|
| |
Remove unused parameter from HASH1 dmas property on stm32mp157c SoC.
Fixes: 1e726a40e067 ("ARM: dts: stm32: Add HASH support on stm32mp157c")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
[Olof: Bug doesn't cause any harm, so shouldn't need stable backport]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
|
| |\
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.20, part 3
- Add ethernet aliases for Stratix10
- Move ethernet aliases from socfpga dtsi
- Correct system manager register size for Stratix10
- Correct SDRAM node address for Arria10
* tag 'socfpga_updates_for_v4.20_part3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
arm64: dts: stratix10: Correct System Manager register size
ARM: dts: socfpga: Fix SDRAM node address for Arria10
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Not all boards use two ethernet devices and/or use them in different
order. As almost all in-tree boards already define their own ethernet
aliases, remove them from the dtsi and add the aliases to the two boards,
that are missing their own definition.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
[dinguyen@kernel.org: rebased to latest dts changes]
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The address in the SDRAM node was incorrect. Fix this to agree with the
correct address and to match the reg definition block.
Cc: stable@vger.kernel.org
Fixes: 54b4a8f57848b("arm: socfpga: dts: Add Arria10 SDRAM EDAC DTS support")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
| |\ \
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.20, second round
Add proper configuration for Odroid XU SD write-protect pin.
* tag 'samsung-dt-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | |
| | | |
| | | |
| | | |
| | | |
| | | |
| | | | |
Add SD card write-protect pin configuration to be sure that it will be
properly pulled down to indicate write access.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
| |\ \ \
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
mvebu dt for 4.20 (part 2)
Auto-detect nand ECC on the armada-385 based board db-88f6820-amc
instead of hard coded them in the device tree.
* tag 'mvebu-dt-4.20-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | |
| | | | | |
This board has a Micron MT29F8G08ABACAWP chip which requires a ECC
strength of 8/512. Rather than hard coding any particular strength the
the nand controller auto-detect the ECC strength based on the ONFI data.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
| |\ \ \ \
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
DaVinci DT updates for v4.20
----------------------------
- A non-critical fix to reduce errors on A/DC on Lego Mindstorms EV3
- Support for GPIO expander on DA850 EVM
* tag 'davinci-for-v4.20/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Due to the electrical design of the A/DC circuits on LEGO MINDSTORMS EV3,
if we are reading analog values as fast as possible (i.e. using DMA to
service the SPI) the A/DC chip will read incorrect values - as much as
0.1V off when the SPI is running at 10MHz. (This has to do with the
capacitor charge time when channels are muxed in the A/DC.)
This patch slows down the SPI as much as possible (if CPU is at 456MHz,
SPI runs at 1/2 of that, so 228MHz and has a max prescalar of 256, so
we could get ~891kHz, but we're just rounding it to 1MHz). We also use
the max allowable value for WDELAY to slow things down even more.
These changes reduce the error of the analog values to about 5mV, which
is tolerable.
Commits a3762b13a596 ("spi: spi-davinci: Add support for SPI_CS_WORD")
and e2540da86ef8 ("iio: adc: ti-ads7950: use SPI_CS_WORD to reduce
CPU usage") introduce changes that allow DMA transfers to be used, so
this slow down is needed now.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
There is a GPIO expander on both the UI board as well as the
baseboard. This patch enables the second tca6416 and identifies
it as being on the baseboard using _bb as the suffix.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
| |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.20
- Add more clocks to NAND controller nodes
- Add SPI controller nodes
- Add SD controller nodes
- Add USB 3.0 and its PHY nodes
- Add PHY nodes for USB 2.0
* tag 'uniphier-dt-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: uniphier: add SD controller nodes
ARM: dts: uniphier: add SD/eMMC controller nodes
arm64: dts: uniphier: add SPI node for LD20, LD11 and PXs3
ARM: dts: uniphier: add SPI node for UniPhier 32bit SoCs
ARM: dts: uniphier: add SPI pin-mux node
arm64: uniphier: dts: add more clocks to Denali NAND controller node
ARM: uniphier: dts: add more clocks to Denali NAND controller node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add nodes of USB2 physical layer for UniPhier SoC. This supports Pro4.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for Pro4, PXs2 and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add SD controller nodes for LD4, Pro4, sLD8, Pro5, and PXs2.
This is also used as an eMMC controller for LD4, Pro4, and sLD8.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add nodes of SPI controller for LD4, Pro4, sLD8, Pro5 and PXs2.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This commit adds pin-mux nodes for SPI controller.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| | |/ / / /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Catch up with the new binding of the Denali IP where three clocks,
"nand", "nand_x", "ecc" are required.
For UniPhier SoCs, the "nand_x" and "ecc" are tied up because they
are both 200MHz.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
| |\ \ \ \ \
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into next/dt
AT91 DT for 4.20 #2
- fixes NAND size and partitions for some boards
* tag 'at91-4.20-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
ARM: dts: at91: at91sam9x5cm: fix addressable nand flash size
ARM: dts: at91: sama5d4_xplained: fix addressable nand flash size
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
sama5d4_xplained, ssam9x5cm, sama5d2_ptc_ek and sama5d3_xplained nand
flashes have a common memory map. Even the nand memory partitions to
match our NAND flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
sama5d3_xplained, sam9x5cm, sama5d2_ptc_ek and sama5d4_xplained nand
flashes have a common memory map. Even the nand memory partitions to
match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
sam9x5cm, sama5d2_ptc_ek, sama5d3_xplained and sama5d4_xplained nand
flashes have a common memory map. Even the nand memory partitions to
match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
The offsets for the bootloader environment and its redundant partition
were inverted. Fix the addresses to match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
at91sam9x5cm comes with a 2Gb NAND flash. Fix the rootfs size to
match this limit.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
sama5d4_xplained comes with a 4Gb NAND flash. Increase the rootfs
size to match this limit.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
| |\ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt
mt7623:
- add pmu node
- add subsystem clocks
- add nodes needed for iommu
- add node for the jpeg decoder
* tag 'v4.19-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: dts: mt7623: add jpeg decoder device node
arm: dts: mt7623: add iommu/smi device nodes
arm: dts: mt7623: update subsystem clock controller device nodes
arm: dts: mt7623: add a performance counter unit device node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Add a jpeg decoder device node for MT7623.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Add iommu/smi device nodes for MT7623.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Update MT7623 subsystem clock controllers, inlcuding mmsys, imgsys,
vdecsys, g3dsys and bdpsys.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
| | | |/ / / /
| | |/| | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add ARM PMU device node to enable hardware perf events.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
| |\ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Nodes for the newly support rk3188 display controller, a fix for a new
dtc warning, gpio setting for the sdmmc regulator on radxarock and a
new board the "S" variant of the rk3288-based Tinker board, that sports
an added emmc.
* tag 'v4.20-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add rk3288-based Tinker board S
ARM: dts: rockchip: move shared tinker-board nodes to a common dtsi
ARM: dts: rockchip: explicitly set vcc_sd0 pin to gpio on rk3188-radxarock
ARM: dts: rockchip: Fix erroneous SPI bus dtc warnings on rk3036
ARM: dts: rockchip: add rk3188 lcd controller nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Add the actual dts for the tinker board S, which brings its own emmc
device, not therefore not requiring an sd-card to boot.
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Tinker Board and Tinker Board S share most of their components,
so should also not replicate these for each variant.
So move them to a shared dtsi that then can get included by both
boards.
Signed-off-by: David Summers <beagleboard@davidjohnsummers.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
dtc has new checks for SPI buses. The rk3036 dts file has a node named
spi' which causes false positive warnings. As the node is a pinctrl child
node, change the node name to be 'spi-pins' to fix the warnings.
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #address-cells for SPI bus
arch/arm/boot/dts/rk3036-evb.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
arch/arm/boot/dts/rk3036-kylin.dtb: Warning (spi_bus_bridge): /pinctrl/spi: incorrect #size-cells for SPI bus
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
| | |/ / / / /
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Add the core display subsystem and vop nodes to rk3188.
Vop0 has a fully dedicated set of pins and only vop1 needs to
do pinctrl to have display output, so also add the necessary
pinctrl entries for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by Sandy Huang <hjc@rock-chips.com>
|
| |\ \ \ \ \ \
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
More devicetree changes for omap variants
There's a patch for previously merged dts changes to remove the last
remaining use of legacy phy_id property.
For dra7, we have a non-urgent PCIe dts fix, enable a PCIe errata for
unaligned access.
For omap5, we enable omap5 USB OTG mode for DWC3 controller.
And we add support for am335x based Moxa UC-2100 series of industrial
computers.
* tag 'omap-for-v4.20/dt-signed-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x: Replace remaining legacy phy_id with phy-handle
ARM: dts: am335x: add support for Moxa UC-2101 open platform
ARM: dts: am335x: add common file for UC-2100 series
ARM: dts: omap5: enable OTG role for DWC3 controller
ARM: dts: dra7: Enable workaround for errata i870 in PCIe host mode
ARM: dts: dra7: Fix up unaligned access setting for PCIe EP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Looks like we still have two instances of phy_handle that did not
get update by Grygorii's series. Let's replace these too with
standard phy-handle.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Neeraj Dantu <dantuguf14105@gmail.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Add support for Moxa UC-2101 open platform
The UC-2101 computing platform is designed for industrial embedded
data acquisition and processing applications.
The features of UC-2101 are:
* eMMC
* SPI flash
* 1x LAN
* 1x RS-232/422/485 ports, software-selectable
* EEPROM
* TPM 2.0
* Watchdog
* RTC
* User gpio-keys
* User LEDs
* User button
Signed-off-by: Wes Huang (黃淵河) <wes.huang@moxa.com>
Signed-off-by: Fero JD Zhou (周俊達) <FeroJD.Zhou@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
The UC-2100 series consists many boards with different peripheral
devices and wireless modules, hence we fetch common items and
create a common dtsi file to increase reusability. All boards in
UC-2100 series will include this common dtsi file.
Signed-off-by: Wes Huang (黃淵河) <wes.huang@moxa.com>
Signed-off-by: Fero JD Zhou (周俊達) <FeroJD.Zhou@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Since SMPS10 and OTG cable detection extcon are described here, and
work to enable OTG power when an OTG cable is plugged in, we can
define OTG mode in the controller (which is disabled by default in
omap5.dtsi).
Tested on OMAP5EVM and Pyra.
Suggested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Add ti,syscon-unaligned-access property to PCIe RC nodes to set
appropriate bits in CTRL_CORE_SMA_SW_7 register to enable workaround for
errata i870.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Bit positions of PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE and
PCIE_SS1_AXI2OCP_LEGACY_MODE_ENABLE in CTRL_CORE_SMA_SW_7 are
incorrectly documented in the TRM. In fact, the bit positions are
swapped. Update the DT bindings for PCIe EP to reflect the same.
Fixes: d23f3839fe97 ("ARM: dts: DRA7: Add pcie1 dt node for EP mode")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| |\| | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Devicetree changes for omap variants
This branch contains a series of improvments for omap3-gta04 phone,
and a series of clean-up for am335x to remove the deprecated phy_id
property.
The rest is to configure am57xx-idk boards for leds, load trigger,
and smps, am3517-evm audio configuration, beaglebone hdmi cec support,
coresight binding update, and fixes for i2c and spi warnings.
* tag 'omap-for-v4.20/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (70 commits)
ARM: dts: add omap3-gta04a5one to Makefile
ARM: dts: omap3-gta04: add pulldown/up settings for twl4030 gpio
ARM: dts: am335x-boneblack: add cec support
ARM: dts: am3517-evm: Add support for UI board and Audio
ARM: dts: gta04: add serial console wakeup irq
ARM: dts: am57xx-idk-common: Hook smps12 regulator as cpu vdd-supply
ARM: dts: omap: Update coresight bindings for hardware ports
ARM: dts: ti: Fix SPI and I2C bus warnings
ARM: dts: dra62x-j5eco-evm: get rid of phy_id property
ARM: dts: dm8148-t410: get rid of phy_id property
ARM: dts: dm8148-evm: get rid of phy_id property
ARM: dts: am57xx-cl-som-am57x: get rid of phy_id property
ARM: dts: am57xx-idk-common: get rid of phy_id property
ARM: dts: dra7-evm: get rid of phy_id property
ARM: dts: dra71-evm: get rid of phy_id property
ARM: dts: dra72-evm-revc: get rid of phy_id property
ARM: dts: dra72-evm: get rid of phy_id property
ARM: dts: dra76-evm: get rid of phy_id property
ARM: dts: am437x-cm-t43: get rid of phy_id property
ARM: dts: am437x-gp-evm: get rid of phy_id property
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
We have defined a new DTS and it should be compiled.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | | |
Pullup and down settings were missing, so add them to avoid
floating pins and make headset detection working.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|