litmus-rt-ext-res.git/drivers/net/ethernet/realtek, branch EXT-RES

r8169: set coherent DMA mask as well as streaming DMA mask

2016-10-15T21:29:38+00:00

PCI devices that are 64-bit DMA capable should set the coherent
DMA mask as well as the streaming DMA mask. On some architectures,
these are managed separately, and so the coherent DMA mask will be
left at its default value of 32 if it is not set explicitly. This
results in errors such as

     r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
     hwdev DMA mask = 0x00000000ffffffff, dev_addr = 0x00000080fbfff000
     swiotlb: coherent allocation failed for device 0000:02:00.0 size=4096
     CPU: 0 PID: 1062 Comm: systemd-udevd Not tainted 4.8.0+ #35
     Hardware name: AMD Seattle/Seattle, BIOS 10:53:24 Oct 13 2016

on systems without memory that is 32-bit addressable by PCI devices.

Signed-off-by: Ard Biesheuvel 
Acked-by: Francois Romieu 
Signed-off-by: David S. Miller

8139cp: Fix one possible deadloop in cp_rx_poll

2016-08-26T00:02:48+00:00

When cp_rx_poll does not get enough packet, it will check the rx
interrupt status again. If so, it will jumpt to rx_status_loop again.
But the goto jump resets the rx variable as zero too.

As a result, it causes one possible deadloop. Assume this case,
rx_status_loop only gets the packet count which is less than budget,
and (cpr16(IntrStatus) & cp_rx_intr_mask) condition is always true.
It causes the deadloop happens and system is blocked.

Signed-off-by: Gao Feng 
Signed-off-by: David S. Miller

8139too: fix system hang when there is a tx timeout event.

2016-08-02T04:38:53+00:00

If tx timeout event occur, kernel will call rtl8139_tx_timeout_task() to reset
hardware. But in this function, driver does not stop tx and rx function before
reset hardware, that will cause system hang.

In this patch, add stop tx and rx function before reset hardware.

Signed-off-by: Chunhao Lin 
Signed-off-by: David S. Miller

r8169: fix nic may not work after changing mac address.

2016-08-01T03:34:05+00:00

When there is no AC power, NIC may not work after changing mac address.
Please refer to following link.
http://www.spinics.net/lists/netdev/msg356572.html

This issue is caused by runtime power management. When there is no AC
power, if we put NIC down (ifconfig down), the driver will be in runtime
suspend state and hardware will be put into D3 state. During this time,
driver cannot access hardware regisers. So if you set new mac address
during this time, it will not be set to hardware. After resume, NIC will
keep using the old mac address and the network will not work normally.

In this patch I add detecting runtime pm status when setting mac address.
If driver is in runtime suspend state, it will skip setting mac address, keep
the new mac address, and set the new mac address during runtime resume.

Signed-off-by: Chunhao Lin 
Signed-off-by: David S. Miller

r8169: add checking driver's runtime pm status in rtl8169_get_ethtool_stats()

2016-08-01T03:34:05+00:00

Not to call rtl8169_update_counters() to dump tally counter when driver
is in runtime suspend state.

Calling rtl8169_update_counters() in runtime suspend state will produce
warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)".

Signed-off-by: Chunhao Lin 
Signed-off-by: David S. Miller

r8169: fix kernel log spam when set or get hardware wol setting.

2016-08-01T03:34:05+00:00

NIC will be put into D3 state during runtime suspend state. When set or
get hardware wol setting, driver will write or read hardware registers.
If we set or get hardware wol setting in runtime suspend state, because
NIC will in D3 state, the hardware registers read by driver will return all
0xff. That will let driver thinking register flag is not toggled and
then prints the warning message "rtl_counters_cond == 1 (loop: 1000,
delay: 10)" to kernel log.

For fixing this issue, add checking driver's pm runtime status in
rtl8169_get_wol() and rtl8169_set_wol().

Signed-off-by: Chunhao Lin 
Signed-off-by: David S. Miller

r8169: default to 64-bit DMA on recent PCIe chips

2016-05-17T18:31:09+00:00

The current logic around the 'use_dac' module parameter prevents the
r81969 driver from being loadable on 64-bit systems without any RAM
below 4 GB when the parameter is left at its default value.

So introduce a new default value -1 which indicates that 64-bit DMA
should be enabled on sufficiently recent PCIe chips, i.e., versions
RTL_GIGA_MAC_VER_18 or later. Explicit param values of 0 or 1 retain
the existing behavior of unconditionally enabling/disabling 64-bit DMA
on 64-bit architectures (i.e., regardless of the type and version of the
chip)

Since PCIe chips do not need to CPlusCmd Dual Address Cycle to be set,
make that conditional on the device type as well.

Cc: Realtek linux nic maintainers 
Signed-off-by: Ard Biesheuvel 
Signed-off-by: David S. Miller

treewide: replace dev->trans_start update with helper

2016-05-04T18:16:49+00:00

Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:

struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)

Compile tested only.

Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Florian Westphal 
Acked-by: Felipe Balbi 
Acked-by: Mugunthan V N 
Acked-by: Antonio Quartulli 
Signed-off-by: David S. Miller

r8169:Remove unnecessary phy reset for pcie nic when setting link spped.

2016-03-14T02:32:44+00:00

For pcie nic, after setting link speed and there is no link driver does not need
to do phy reset until link up.

For some pcie nics, to do this will also reset phy speed down counter and prevent
phy from auto speed down.

This patch fix the issue reported in following link.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1547151

Signed-off-by: Chunhao Lin 
Signed-off-by: David S. Miller

r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_41~48

2016-03-02T18:59:14+00:00

For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate
message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002
address=0x0000000000003000 flags=0x0050] in dmesg.

Signed-off-by: Chunhao Lin 
Signed-off-by: David S. Miller