litmus-rt-ext-res.git/drivers/net/ethernet/dlink, branch EXT-RES

sundance: use IS_ENABLED() instead of checking for built-in or module

2016-09-13T03:27:58+00:00

The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.

Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.

Signed-off-by: Javier Martinez Canillas 
Signed-off-by: David S. Miller

treewide: replace dev->trans_start update with helper

2016-05-04T18:16:49+00:00

Replace all trans_start updates with netif_trans_update helper.
change was done via spatch:

struct net_device *d;
@@
- d->trans_start = jiffies
+ netif_trans_update(d)

Compile tested only.

Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: linux-xtensa@linux-xtensa.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-rdma@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-can@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: linux-wireless@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: linux-bluetooth@vger.kernel.org
Signed-off-by: Florian Westphal 
Acked-by: Felipe Balbi 
Acked-by: Mugunthan V N 
Acked-by: Antonio Quartulli 
Signed-off-by: David S. Miller

dl2k: Implement suspend

2015-11-20T19:48:27+00:00

Add suspend/resume support to dl2k driver.
This requires RX/TX rings to be reset so split out the required
functionality from alloc_list() into new rio_reset_ring().

Tested on Asus NX1101 (IP1000A) and D-Link DGE-550T (DL-2000).

Signed-off-by: Ondrej Zary 
Signed-off-by: David S. Miller

dl2k: Reorder and cleanup initialization

2015-11-20T19:48:27+00:00

Move HW init and stop into separate functions.
Request IRQ only after the HW has been reset (so interrupts are
disabled and no stale interrupts are pending).

Signed-off-by: Ondrej Zary 
Signed-off-by: David S. Miller

dl2k: Handle memory allocation errors in alloc_list

2015-11-20T19:48:27+00:00

If memory allocation fails in alloc_list(), free the already allocated
memory and return -ENOMEM. In rio_open(), call alloc_list() first and
abort if it fails. Move HW access (set RFDListPtr) out ot alloc_list().

Signed-off-by: Ondrej Zary 
Signed-off-by: David S. Miller

dl2k: Add support for IP1000A-based cards

2015-11-16T22:11:31+00:00

Add support for IP1000A chips to dl2k driver.
IP1000A chip looks like a TC9020 with integrated PHY.

This allows IP1000A chips to work reliably because the ipg driver is
buggy - it loses packets under load and then completely stops
transmitting data.

Tested with Asus NX1101 v2.0 at 10, 100 and 1000Mbps:
vendor=0x13f0 device=0x1023 (rev 0x41)
subsystem vendor=0x1043 device=0x8180

MAC address registers access needed to be changed from 8-bit to 16-bit
because 8-bit does not work on IP1000A. 8-bit access is not even
allowed in the TC9020 datasheet (although it worked). 16-bit access
works on both.

Tested that it does not break D-Link DGE-550T (DL-2000 chip, probably
a rebranded TC9020):
vendor=0x1186 device=0x4000 (rev 0x0c)
subsystem vendor=0x1186 device=0x4000

Signed-off-by: Ondrej Zary 
Reviewed-by: Andy Shevchenko 
Signed-off-by: David S. Miller

drivers/net: remove all references to obsolete Ethernet-HOWTO

2015-06-23T13:50:35+00:00

This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it.  And there is
no value in anyone else taking over updating it either.

However the references to it continue to spread as boiler plate text
from one Kconfig file into the next.  We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.

No code is changed in this commit, just Kconfig help text.

Signed-off-by: Paul Gortmaker 
Signed-off-by: David S. Miller

net: dl2k: Use setup_timer

2015-06-01T04:34:38+00:00

Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.

A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:

@change@
expression e1, e2, e3, e4, a, b;
@@

-init_timer(&e1);
+setup_timer(&e1, a, b);

... when != a = e2
    when != b = e3

-e1.data = b;
... when != a = e4
-e1.function = a;

Signed-off-by: Vaishali Thakkar 
Signed-off-by: David S. Miller

PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use

2014-08-12T18:15:14+00:00

We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// 

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// 

[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine 
Signed-off-by: Bjorn Helgaas

net: use SPEED_UNKNOWN and DUPLEX_UNKNOWN when appropriate

2014-06-06T23:24:07+00:00

Signed-off-by: Jiri Pirko 
Signed-off-by: David S. Miller