summaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAge
* mac80211: skip netdev queue control with software queuingMichal Kazior2016-06-09
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qdiscs are designed with no regard to 802.11 aggregation requirements and hand out packet-by-packet with no guarantee they are destined to the same tid. This does more bad than good no matter how fairly a given qdisc may behave on an ethernet interface. Software queuing used per-AC netdev subqueue congestion control whenever a global AC limit was hit. This meant in practice a single station or tid queue could starve others rather easily. This could resonate with qdiscs in a bad way or could just end up with poor aggregation performance. Increasing the AC limit would increase induced latency which is also bad. Disabling qdiscs by default and performing taildrop instead of netdev subqueue congestion control on the other hand makes it possible for tid queues to fill up "in the meantime" while preventing stations starving each other. This increases aggregation opportunities and should allow software queuing based drivers achieve better performance by utilizing airtime more efficiently with big aggregates. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* nl80211: clarify nl80211_set_reg() success pathJohannes Berg2016-06-09
| | | | | | | | | Setting rd to NULL to avoid freeing it, just to be able to return from the function in a single place, doesn't make much sense. Return the set_regdom() return value directly. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* wext: reformat struct/union declarationsJohannes Berg2016-06-09
| | | | | | | | Everytime I need to look for these, my usual strategy fails because it assumes the right formatting. Fix the formatting here to make it consistent with the rest of the kernel. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* nl80211: Fix checkpatch warnings about blank linesKirtika Ruchandani2016-06-09
| | | | | | | | | | | This patch fixes the following checkpatch.pl issues - - Please don't use multiple blank lines - Blank lines aren't necessary before a close brace - Missing a blank line after declarations Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Kirtika Ruchandani <kirtika.ruchandani@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* nl80211: Fix spellingKirtika Ruchandani2016-06-09
| | | | | | | | Fix 'implementation' spelling, reported by checkpatch.pl Signed-off-by: Kirtika Ruchandani <kirtika.ruchandani@gmail.com> Reviewed-by: Julian Calaby <julian.calaby@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: Advertise extended capabilities per interface type to userspaceKanchanapally, Vidyullatha2016-05-31
| | | | | | | | | | | | | The driver extended capabilities may differ for different interface types which the userspace needs to know (for example the fine timing measurement initiator and responder bits might differ for a station and AP). Add a new nl80211 attribute to provide extended capabilities per interface type to userspace. Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com> Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* cfg80211: Allow cfg80211_connect_result() errors to be distinguishedJouni Malinen2016-05-31
| | | | | | | | | | | | | | | | | | | | | | | | | Previously, the status parameter to cfg80211_connect_result() was documented as using WLAN_STATUS_UNSPECIFIED_FAILURE (1) when the real status code for the failure is not known. This value can be used by an AP (and often is) and as such, user space cannot distinguish between explicitly rejected authentication/association and not being able to even try to associate or not receiving a response from the AP. Add a new inline function, cfg80211_connect_timeout(), to be used when the driver knows that the connection attempt failed due to a reason where connection could not be attempt or no response was received from the AP. The internal functions now allow a negative status value (-1) to be used as an indication of this special case. This results in the NL80211_ATTR_TIMED_OUT to be added to the NL80211_CMD_CONNECT event to allow user space to determine this case was hit. For backwards compatibility, NL80211_STATUS_CODE with the value WLAN_STATUS_UNSPECIFIED_FAILURE is still indicated in the event in such a case. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> [johannes: fix cfg80211_connect_bss() prototype to use int for status, add cfg80211_connect_timeout() to docbook, fix docbook] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211: add vht cap decode to debugfsBen Greear2016-05-31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This makes it a lot easier to understand the capabilities used by the station: VHT supported cap: 0x300819b2 MAX-MPDU-11454 80Mhz RXLDPC SHORT-GI-80 TXSTBC RXSTBC_1 SU-BEAMFORMER-CAPABLE SU-BEAMFORMEE-CAPABLE BEAMFORMEE-STS: 0x0 SOUNDING-DIMENSIONS: 0x0 MU-BEAMFORMER-CAPABLE MPDU-LENGTH-EXPONENT: 0x0 LINK-ADAPTATION-VHT-MRQ-MFB: 0x0 RX-ANTENNA-PATTERN TX-ANTENNA-PATTERN RX MCS: fffe TX MCS: fffe Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* mac80211_hwsim: Allow managing radios from non-initial namespacesMartin Willi2016-05-31
| | | | | | | | | | | | | | | | | | | | | | | | While wiphys can be moved into network namespaces over nl80211, the creation and removal of hwsim radios is currently limited to the initial namespace. This patch allows management of namespaced radios from the owning namespace by setting genetlink netnsok. To prevent two arbitrary namespaces to communicate over the simulated shared medium, radios are separated by netgroups. Each radio created in the same namespace lives in the same netgroup and hence can communicate with other radios in that group. When moving radios to other namespaces, the netgroup is preserved, so two radios having the same netgroup can communicate even if not in the same namespace; This allows a controlling namespace to create radios and move them to other namespaces for communication. When a net namespace owning a radio exits, the radio is destroyed unless it was created in the initial network namespace. This keeps the previous behavior by returning them to the init namespace, but prevents unprivileged users from creating radios in the initial namespace. Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* nl80211: Allow privileged operations from user namespacesMartin Willi2016-05-31
| | | | | | | | | | | | | | | | | | | While a wiphy can be transferred to network namespaces, a process having CAP_NET_ADMIN in a non-initial user namespace can not administrate such devices due to the genetlink GENL_ADMIN_PERM restrictions. For openvswitch having the same issue, a new GENL_UNS_ADMIN_PERM flag has been introduced, commit 4a92602aa1cd ("openvswitch: allow management from inside user namespaces"). This patch changes all privileged operations operating on a wiphy, dev or wdev to allow their administration using the same mechanism. All operations use either NEED_WIPHY, NEED_WDEV or NEED_NETDEV, which implies a namespace aware lookup of the device. The only exception is NL80211_CMD_SET_WIPHY, which explicitly uses a namespace aware phy lookup. Signed-off-by: Martin Willi <martin@strongswan.org> [also allow cancel scan, for completeness] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds2016-05-19
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull MIPS updates from Ralf Baechle: "This is the main pull request for MIPS for 4.7. Here's the summary of the changes: - ATH79: Support for DTB passuing using the UHI boot protocol - ATH79: Remove support for builtin DTB. - ATH79: Add zboot debug serial support. - ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega and DPT-Module. - ATH79: Update devicetree clock support for AR9132 and AR9331. - ATH79: Cleanup the DT code. - ATH79: Support newer SOCs in ath79_ddr_ctrl_init. - ATH79: Fix regression in PCI window initialization. - BCM47xx: Move SPROM driver to drivers/firmware/ - BCM63xx: Enable partition parser in defconfig. - BMIPS: BMIPS5000 has I cache filing from D cache - BMIPS: BMIPS: Add cpu-feature-overrides.h - BMIPS: Add Whirlwind support - BMIPS: Adjust mips-hpt-frequency for BCM7435 - BMIPS: Remove maxcpus from BCM97435SVMB DTS - BMIPS: Add missing 7038 L1 register cells to BCM7435 - BMIPS: Various tweaks to initialization code. - BMIPS: Enable partition parser in defconfig. - BMIPS: Cache tweaks. - BMIPS: Add UART, I2C and SATA devices to DT. - BMIPS: Add BCM6358 and BCM63268support - BMIPS: Add device tree example for BCM6358. - BMIPS: Improve Improve BCM6328 and BCM6368 device trees - Lantiq: Add support for device tree file from boot loader - Lantiq: Allow build with no built-in DT. - Loongson 3: Reserve 32MB for RS780E integrated GPU. - Loongson 3: Fix build error after ld-version.sh modification - Loongson 3: Move chipset ACPI code from drivers to arch. - Loongson 3: Speedup irq processing. - Loongson 3: Add basic Loongson 3A support. - Loongson 3: Set cache flush handlers to nop. - Loongson 3: Invalidate special TLBs when needed. - Loongson 3: Fast TLB refill handler. - MT7620: Fallback strategy for invalid syscfg0. - Netlogic: Fix CP0_EBASE redefinition warnings - Octeon: Initialization fixes - Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite - Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig - Octeon: Correctly handle endian-swapped initramfs images. - Octeon: Support CN73xx, CN75xx and CN78xx. - Octeon: Remove dead code from cvmx-sysinfo. - Octeon: Extend number of supported CPUs past 32. - Octeon: Remove some code limiting NR_IRQS to 255. - Octeon: Simplify octeon_irq_ciu_gpio_set_type. - Octeon: Mark some functions __init in smp.c - Octeon: Octeon: Add Octeon III CN7xxx interface detection - PIC32: Add serial driver and bindings for it. - PIC32: Add PIC32 deadman timer driver and bindings. - PIC32: Add PIC32 clock timer driver and bindings. - Pistachio: Determine SoC revision during boot - Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER. - Sibyte: Strip redundant comments from bcm1480_regs.h. - Panic immediately if panic_on_oops is set. - module: fix incorrect IS_ERR_VALUE macro usage. - module: Make consistent use of pr_* - Remove no longer needed work_on_cpu() call. - Remove CONFIG_IPV6_PRIVACY from defconfigs. - Fix registers of non-crashing CPUs in dumps. - Handle MIPSisms in new vmcore_elf32_check_arch. - Select CONFIG_HANDLE_DOMAIN_IRQ and make it work. - Allow RIXI to be used on non-R2 or R6 cores. - Reserve nosave data for hibernation - Fix siginfo.h to use strict POSIX types. - Don't unwind user mode with EVA. - Fix watchpoint restoration - Ptrace watchpoints for R6. - Sync icache when it fills from dcache - I6400 I-cache fills from dcache. - Various MSA fixes. - Cleanup MIPS_CPU_* definitions. - Signal: Move generic copy_siginfo to signal.h - Signal: Fix uapi include in exported asm/siginfo.h - Timer fixes for sake of KVM. - XPA TLB refill fixes. - Treat perf counter feature - Update John Crispin's email address - Add PIC32 watchdog and bindings. - Handle R10000 LL/SC bug in set_pte() - cpufreq: Various fixes for Longson1. - R6: Fix R2 emulation. - mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes - ELF: ABI and FP fixes. - Allow for relocatable kernel and use that to support KASLR. - Fix CPC_BASE_ADDR mask - Plenty fo smp-cps, CM, R6 and M6250 fixes. - Make reset_control_ops const. - Fix kernel command line handling of leading whitespace. - Cleanups to cache handling. - Add brcm, bcm6345-l1-intc device tree bindings. - Use generic clkdev.h header - Remove CLK_IS_ROOT usage. - Misc small cleanups. - CM: Fix compilation error when !MIPS_CM - oprofile: Fix a preemption issue - Detect DSP ASE v3 support:1" * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits) MIPS: pic32mzda: fix getting timer clock rate. MIPS: ath79: fix regression in PCI window initialization MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs MIPS: Fix VZ probe gas errors with binutils <2.24 MIPS: perf: Fix I6400 event numbers MIPS: DEC: Export `ioasic_ssr_lock' to modules MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC MIPS: CM: Fix compilation error when !MIPS_CM MIPS: Fix genvdso error on rebuild USB: ohci-jz4740: Remove obsolete driver MIPS: JZ4740: Probe OHCI platform device via DT MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant MIPS: pistachio: Determine SoC revision during boot MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435 mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type MIPS: Prevent "restoration" of MSA context in non-MSA kernels MIPS: cevt-r4k: Dynamically calculate min_delta_ns MIPS: malta-time: Take seconds into account MIPS: malta-time: Start GIC count before syncing to RTC MIPS: Force CPUs to lose FP context during mode switches ...
| * MIPS: pic32mzda: fix getting timer clock rate.Purna Chandra Mandal2016-05-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | PIC32 clock driver is now implemented as platform driver instead of as part of of_clk_init(). It meants all the clock modules are available quite late in the boot sequence. So request for CPU clock by clk_get_sys() and clk_get_rate() to find c0_timer rate fails. To fix this use PIC32 specific early clock functions implemented for early console support. Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: Joshua Henderson <digitalpeer@digitalpeer.com> Patchwork: https://patchwork.linux-mips.org/patch/13262/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: ath79: fix regression in PCI window initializationFelix Fietkau2016-05-17
| | | | | | | | | | | | | | | | | | | | | | | | | | ath79_ddr_pci_win_base has the type void __iomem *, so register offsets need to be a multiple of 4. Cc: Alban Bedel <albeu@free.fr> Fixes: 24b0e3e84fbf ("MIPS: ath79: Improve the DDR controller interface") Signed-off-by: Felix Fietkau <nbd@nbd.name> Cc: sergei.shtylyov@cogentembedded.com Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13258/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCsFelix Fietkau2016-05-17
| | | | | | | | | | | | | | | | | | | | | | | | | | AR913x, AR724x and AR933x are the only SoCs where the ath79_ddr_wb_flush_base starts at 0x7c, all newer SoCs use 0x9c Invert the logic to make the code compatible with AR95xx Signed-off-by: Felix Fietkau <nbd@nbd.name> Cc: albeu@free.fr Cc: sergei.shtylyov@cogentembedded.com Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13257/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Fix VZ probe gas errors with binutils <2.24James Hogan2016-05-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VZ guest register & TLB access macros introduced in commit "MIPS: Add guest CP0 accessors" use VZ ASE specific instructions that aren't understood by versions of binutils prior to 2.24. Add a check for whether the toolchain supports the -mvirt option, similar to the MSA toolchain check, and implement the accessors using .word if not. Due to difficulty in converting compiler specified registers (e.g. "$3") to usable numbers (e.g. "3") in inline asm, we need to copy to/from a temporary register, namely the assembler temporary (at/$1), and specify guest CP0 registers numerically in the gc0 macros. Fixes: 7eb91118227d ("MIPS: Add guest CP0 accessors") Signed-off-by: James Hogan <james.hogan@imgtec.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Cc: linux-next@vger.kernel.org Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13255/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: perf: Fix I6400 event numbersJames Hogan2016-05-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix perf hardware performance counter event numbers for I6400. This core does not follow the performance event numbering scheme of previous MIPS cores. All performance counters (both odd and even) are capable of counting any of the available events. Fixes: 4e88a8621301 ("MIPS: Add cases for CPU_I6400") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13259/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: DEC: Export `ioasic_ssr_lock' to modulesMaciej W. Rozycki2016-05-17
| | | | | | | | | | | | | | | | | | | | Fix a modular `declance' regression caused by LMO commit bb46bf30d13f ("DECstation SCSI driver clean-ups.") Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13256/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCCMaciej W. Rozycki2016-05-17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix a build regression from commit c9017757c532 ("MIPS: init upper 64b of vector registers when MSA is first used"): arch/mips/built-in.o: In function `enable_restore_fp_context': traps.c:(.text+0xbb90): undefined reference to `_init_msa_upper' traps.c:(.text+0xbb90): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper' traps.c:(.text+0xbef0): undefined reference to `_init_msa_upper' traps.c:(.text+0xbef0): relocation truncated to fit: R_MIPS_26 against `_init_msa_upper' to !CONFIG_CPU_HAS_MSA configurations with older GCC versions, which are unable to figure out that calls to `_init_msa_upper' are indeed dead. Of the many ways to tackle this failure choose the approach we have already taken in `thread_msa_context_live'. [ralf@linux-mips.org: Drop patch segment to junk file.] Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: stable@vger.kernel.org # v3.16+ Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13271/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: CM: Fix compilation error when !MIPS_CMTony Wu2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | Fix mips_cm_lock_other compilation error when MIPS_CM is not selected. This was introduced in commit 23d5de8efb9a (MIPS: CM: Introduce core-other locking functions) Signed-off-by: Tony Wu <tung7970@gmail.com> Cc: Paul Burton <paul.burton@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/11698/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Fix genvdso error on rebuildJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The genvdso program modifies the debug and stripped versions of the VDSOs in place, and errors if the modification has already taken place. Unfortunately this means that a rebuild which tries to rerun genvdso to generate vdso*-image.c without also rebuilding vdso.so.dbg (for example if genvdso.c is modified) hits a build error like this: arch/mips/vdso/genvdso 'arch/mips/vdso/vdso.so.dbg' already contains a '.MIPS.abiflags' section This is fixed by reorganising the rules such that unmodified .so files have a .raw suffix, and these are copied in the same rule that runs genvdso on the copies. I.e. previously we had: cmd_vdsold: link objects -> vdso.so.dbg cmd_genvdso: strip vdso.so.dbg -> vdso.so run genvdso -> vdso-image.c and modify vdso.so.dbg and vdso.so in place Now we have: cmd_vdsold: link objects -> vdso.so.dbg.raw a new cmd_objcopy based strip rule (inspired by ARM): strip vdso.so.dbg.raw -> vdso.so.raw cmd_genvdso: copy vdso.so.dbg.raw -> vdso.so.dbg copy vdso.so.raw -> vdso.so run genvdso -> vdso-image.c and modify vdso.so.dbg and vdso.so in place Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13250/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * USB: ohci-jz4740: Remove obsolete driverMaarten ter Huurne2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ohci-platform driver can control the clock, while usb-nop-xceiv as the PHY can control the vbus regulator. So this JZ4740-specific glue is not needed anymore. Signed-off-by: Maarten ter Huurne <maarten@treewalker.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Paul Cercueil <paul@crapouillou.net> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13105/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: JZ4740: Probe OHCI platform device via DTMaarten ter Huurne2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DT fragment will select the ohci-platform driver, since that can handle the JZ4740 OHCI just fine. While I don't have a JZ4740-based board with anything connected to the USB host controller, I did test the generic OHCI driver successfully on a JZ4770-based board. The device is disabled by default; boards that want to use it can override the "status" property. The mass-production Qi LB60 boards don't use the USB host controller. Signed-off-by: Maarten ter Huurne <maarten@treewalker.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Paul Cercueil <paul@crapouillou.net> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13104/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: JZ4740: Qi LB60: Remove support for AVT2 variantMaarten ter Huurne2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | AVT2 was a prototype board of which about 5 were made, none of which are in use anymore. Signed-off-by: Maarten ter Huurne <maarten@treewalker.org> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Cc: Paul Cercueil <paul@crapouillou.net> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13103/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: pistachio: Determine SoC revision during bootJames Hartley2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that there are different revisions of the Pistachio SoC in circulation, add this information to the boot log to make it easier for users to determine which hardware they have. Signed-off-by: James Hartley <james.hartley@imgtec.com> Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: Jonas Gorski <jogo@openwrt.org> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13130/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435Florian Fainelli2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The CPU actually runs at 1405Mhz which gives us a 175625000 Hz MIPS timer frequency (CPU frequency / 8). Fixes: e4c7d009654a ("MIPS: BMIPS: Add BCM7435 dtsi") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Cc: linux-mips@linux-mips.org Cc: john@phrozen.org Cc: cernekee@gmail.com Cc: jaedon.shin@gmail.com Patchwork: https://patchwork.linux-mips.org/patch/13132/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for ↵Sashka Nochkin2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | the memory type Mediatek MT7620 SoC has syscfg0 bits where it sets the type of memory being used. However, sometimes those bits are not set properly (reading "11"). In this case, the SoC assumes SDRAM. The patch below reflects that. Signed-off-by: Sashka Nochkin <linux-mips@durdom.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13135/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Prevent "restoration" of MSA context in non-MSA kernelsPaul Burton2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a kernel doesn't support MSA context (ie. CONFIG_CPU_HAS_MSA=n) then it will only keep 64 bits per FP register in thread context, and the calls to set_fpr64 in restore_msa_extcontext will overrun the end of the FP register context into the FCSR & MSACSR values. GCC 6.x has become smart enough to detect this & complain like so: arch/mips/kernel/signal.c: In function 'protected_restore_fp_context': ./arch/mips/include/asm/processor.h:114:17: error: array subscript is above array bounds [-Werror=array-bounds] fpr->val##width[FPR_IDX(width, idx)] = val; \ ~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~ ./arch/mips/include/asm/processor.h:118:1: note: in expansion of macro 'BUILD_FPR_ACCESS' BUILD_FPR_ACCESS(64) The only way to trigger this code to run would be for a program to set up an artificial extended MSA context structure following a sigframe & execute sigreturn. Whilst this doesn't allow a program to write to any state that it couldn't already, it makes little sense to allow this "restoration" of MSA context in a system that doesn't support MSA. Fix this by killing a program with SIGSYS if it tries something as crazy as "restoring" fake MSA context in this way, also fixing the build error & allowing for most of restore_msa_extcontext to be optimised out of kernels without support for MSA. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: Michal Toman <michal.toman@imgtec.com> Fixes: bf82cb30c7e5 ("MIPS: Save MSA extended context around signals") Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: James Hogan <james.hogan@imgtec.com> Cc: Michal Toman <michal.toman@imgtec.com> Cc: linux-mips@linux-mips.org Cc: stable <stable@vger.kernel.org> # v4.3+ Patchwork: https://patchwork.linux-mips.org/patch/13164/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: cevt-r4k: Dynamically calculate min_delta_nsJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Calculate the MIPS clockevent device's min_delta_ns dynamically based on the time it takes to perform the mips_next_event() sequence. Virtualisation in particular makes the current fixed min_delta of 0x300 inappropriate under some circumstances, as the CP0_Count and CP0_Compare registers may be being emulated by the hypervisor, and the frequency may not correspond directly to the CPU frequency. We actually use twice the median of multiple 75th percentiles of multiple measurements of how long the mips_next_event() sequence takes, in order to fairly efficiently eliminate outliers due to unexpected hypervisor latency (which would need handling with retries when it occurs during normal operation anyway). Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13176/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: malta-time: Take seconds into accountJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When estimating the clock frequency based on the RTC, take seconds into account in case the Update In Progress (UIP) bit wasn't seen. This can happen in virtual machines (which may get pre-empted by the hypervisor at inopportune times) with QEMU emulating the RTC (and in fact not setting the UIP bit for very long), especially on slow hosts such as FPGA systems and hardware emulators. This results in several seconds actually having elapsed before seeing the UIP bit instead of just one second, and exaggerated timer frequencies. While updating the comments, they're also fixed to match the code in that the rising edge of the update flag is detected first, not the falling edge. The rising edge gives a more precise point to read the counters in a virtualised system than the falling edge, resulting in a more accurate frequency. It does however mean that we have to also wait for the falling edge before doing the read of the RTC seconds register, otherwise it seems to be possible in slow hardware emulation to stray into the interval when the RTC time is undefined during the update (at least 244uS after the rising edge of the update flag). This can result in both seconds values reading the same, and it wrapping to 60 seconds, vastly underestimating the frequency. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13174/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: malta-time: Start GIC count before syncing to RTCJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The sampling of the GIC counter on Malta after observing a rising edge of the RTC update flag differs slightly between the first and second sample, with the first sample also calling gic_start_count(). The two samples should really be taken as similarly as possible to get the most accurate figure, so move the gic_start_count() call before detecting the rising edge. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13173/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Force CPUs to lose FP context during mode switchesPaul Burton2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS") added support for the PR_SET_FP_MODE prctl, which allows a userland program to modify its FP mode at runtime. This is most notably required if dynamic linking leads to the FP mode requirement changing at runtime from that indicated in the initial executable's ELF header. In order to avoid overhead in the general FP context restore code, it aimed to have threads in the process become unable to enable the FPU during a mode switch & have the thread calling the prctl syscall wait for all other threads in the process to be context switched at least once. Once that happens we can know that no thread in the process whose mode will be switched has live FP context, and it's safe to perform the mode switch. However in the (rare) case of modeswitches occurring in multithreaded programs this can lead to indeterminate delays for the thread invoking the prctl syscall, and the code monitoring for those context switches was woefully inadequate for all but the simplest cases. Fix this by broadcasting an IPI if other CPUs may have live FP context for an affected thread, with a handler causing those CPUs to relinquish their FPU ownership. Threads will then be allowed to continue running but will stall on the wait_on_atomic_t in enable_restore_fp_context if they attempt to use FP again whilst the mode switch is still in progress. The end result is less fragile poking at scheduler context switch counts & a more expedient completion of the mode switch. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS") Reviewed-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: stable <stable@vger.kernel.org> # v4.0+ Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13145/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Disable preemption during prctl(PR_SET_FP_MODE, ...)Paul Burton2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Whilst a PR_SET_FP_MODE prctl is performed there are decisions made based upon whether the task is executing on the current CPU. This may change if we're preempted, so disable preemption to avoid such changes for the lifetime of the mode switch. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Fixes: 9791554b45a2 ("MIPS,prctl: add PR_[GS]ET_FP_MODE prctl options for MIPS") Reviewed-by: Maciej W. Rozycki <macro@imgtec.com> Tested-by: Aurelien Jarno <aurelien@aurel32.net> Cc: Adam Buchbinder <adam.buchbinder@gmail.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: stable <stable@vger.kernel.org> # v4.0+ Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13144/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Allow emulation for unaligned [LS]DXC1 instructionsPaul Burton2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | If an address error exception occurs for a LDXC1 or SDXC1 instruction, within the cop1x opcode space, allow it to be passed through to the FPU emulator rather than resulting in a SIGILL. This causes LDXC1 & SDXC1 to be handled in a manner consistent with the more common LDC1 & SDC1 instructions. Signed-off-by: Paul Burton <paul.burton@imgtec.com> Tested-by: Aurelien Jarno <aurelien@aurel32.net> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13143/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: ptrace: Prevent writes to read-only FCSR bitsMaciej W. Rozycki2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Correct the cases missed with commit 9b26616c8d9d ("MIPS: Respect the ISA level in FCSR handling") and prevent writes to read-only FCSR bits there. This in particular applies to FP context initialisation where any IEEE 754-2008 bits preset by `mips_set_personality_nan' are cleared before the relevant ptrace(2) call takes effect and the PTRACE_POKEUSR request addressing FPC_CSR where no masking of read-only FCSR bits is done. Remove the FCSR clearing from FP context initialisation then and unify PTRACE_POKEUSR/FPC_CSR and PTRACE_SETFPREGS handling, by factoring out code from `ptrace_setfpregs' and calling it from both places. This mostly matters to soft float configurations where the emulator can be switched this way to a mode which should not be accessible and cannot be set with the CTC1 instruction. With hard float configurations any effect is transient anyway as read-only bits will retain their values at the time the FP context is restored. Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: stable@vger.kernel.org # v4.0+ Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13239/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: ptrace: Fix FP context restoration FCSR regressionMaciej W. Rozycki2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix a floating-point context restoration regression introduced with commit 9b26616c8d9d ("MIPS: Respect the ISA level in FCSR handling") that causes a Floating Point exception and consequently a kernel oops with hard float configurations when one or more FCSR Enable and their corresponding Cause bits are set both at a time via a ptrace(2) call. To do so reinstate Cause bit masking originally introduced with commit b1442d39fac2 ("MIPS: Prevent user from setting FCSR cause bits") to address this exact problem and then inadvertently removed from the PTRACE_SETFPREGS request with the commit referred above. Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: stable@vger.kernel.org # v4.0+ Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13238/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: dts: pic32: Update dts to reflect new PIC32MZDA clk bindingPurna Chandra Mandal2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - now clock nodes definition is merged with core .dtsi file - only one rootclk is now part of DT - clock clients also updated based on new binding doc Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Kumar Gala <galak@codeaurora.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Sandeep Sheriker <sandeepsheriker.mallikarjun@microchip.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-clk@vger.kernel.org Cc: devicetree@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13248/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * CLK: microchip: Add Microchip PIC32 clock driver.Purna Chandra Mandal2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This clock driver implements PIC32 specific clock-tree. clock-tree entities can only be configured through device-tree file (OF). Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> Cc: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-clk@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13247/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * dt/bindings/clk: Add PIC32 clock binding documentation.Purna Chandra Mandal2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Document the devicetree bindings for the clock driver found on Microchip PIC32 class devices. Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Michael Turquette <mturquette@baylibre.com> Cc: Stephen Boyd <sboyd@codeaurora.org> Cc: Purna Chandra Mandal <purna.mandal@microchip.com> Cc: Kumar Gala <galak@codeaurora.org> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-clk@vger.kernel.org Cc: devicetree@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13246/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: ELF: Unify ABI classification macrosMaciej W. Rozycki2016-05-13
| | | | | | | | | | | | | | | | | | | | | | Remove a duplicate o32 `elf_check_arch' implementation, move all macro variants to <asm/elf.h> and define them unconditionally under indvidual names, substituting alias `elf_check_arch' definitions in variant code. Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13245/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: ELF: Unify __MIPS_O32_FP64_MUST_BE_ZERO definitionsMaciej W. Rozycki2016-05-13
| | | | | | | | | | | | | | Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13244/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: ELF: Deconditionalise ABI flags definitionsMaciej W. Rozycki2016-05-13
| | | | | | | | | | | | | | | | | | | | Move the `mips_elf_abiflags_v0' structure and FP ABI flag macros outside #ifndef ELF_ARCH. These are public interfaces. Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13243/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Print GuestCtl1 on machine check exceptionJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | The GuestCtl1 CP0 register can contain the GuestID used for root TLB operations, which affects TLB matching. The other TLB registers are already dumped out to the log on a machine check exception due to multiple matching TLB entries, so also dump the value of the GuestCtl1 register if GuestIDs are supported. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13232/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: dump_tlb: Preserve and dump GuestIDJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | The GuestID for root TLB operations (GuestCtl1.RID) is modified by TLB reads, so needs preserving by dump_tlb() like the ASID field of EntryHi. Also dump the GuestID of each entry if it exists alongside the ASID, as it forms an important part of the TLB entry when VZ guests are used. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13230/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Add probing & defs for VZ & guest featuresJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add a few new cpu-features.h definitions for VZ sub-features, namely the existence of the CP0_GuestCtl0Ext, CP0_GuestCtl1, and CP0_GuestCtl2 registers, and support for GuestID to dialias TLB entries belonging to different guests. Also add certain features present in the guest, with the naming scheme cpu_guest_has_*. These are added separately to the main options bitfield since they generally parallel similar features in the root context. A few of these (FPU, MSA, watchpoints, perf counters, CP0_[X]ContextConfig registers, MAAR registers, and probably others in future) can be dynamically configured in the guest context, for which the cpu_guest_has_dyn_* macros are added. [ralf@linux-mips.org: Resolve merge conflict.] Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13231/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Add guest CP0 accessorsJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | Add guest CP0 accessors and guest TLB operations along the same lines as the existing macros and functions for the root CP0. Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13229/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Add register definitions for VZ ASE registersJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | Add various register definitions to <asm/mipsregs.h> for the coprocessor zero registers in the VZ ASE, namely CP0_GuestCtl0, CP0_GuestCtl0Ext, CP0_GuestCtl1, CP0_GuestCtl2, CP0_GuestCtl3, and CP0_GTOffset. Signed-off-by: James Hogan <james.hogan@imgtec.com> Acked-by: David Daney <david.daney@cavium.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13228/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Avoid magic numbers probing kscratch_maskJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | The decode_config4() function reads kscratch_mask from CP0_Config4.KScrExist using a hard coded shift and mask. We already have a definition for the mask in mipsregs.h, so add a definition for the shift and make use of them. Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13227/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Add perf counter featureJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add CPU feature for standard MIPS r2 performance counters, as determined by the Config1.PC bit. Both perf_events and oprofile probe this bit, so lets combine the probing and change both to use cpu_has_perf. This will also be used for VZ support in KVM to know whether performance counters exist which can be exposed to guests. [ralf@linux-mips.org: resolve conflict.] Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Robert Richter <rric@kernel.org> Cc: linux-mips@linux-mips.org Cc: oprofile-list@lists.sf.net Patchwork: https://patchwork.linux-mips.org/patch/13226/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Add defs & probing of [X]ContextConfigJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The CP0_[X]ContextConfig registers are present if CP0_Config3.CTXTC or CP0_Config3.SM are set, and provide more control over which bits of CP0_[X]Context are set to the faulting virtual address on a TLB exception. KVM/VZ will need to be able to save and restore these registers in the guest context, so add the relevant definitions and probing of the ContextConfig feature in the root context first. [ralf@linux-mips.org: resolve merge conflict.] Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13225/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| * MIPS: Add defs & probing of BadInstr[P] registersJames Hogan2016-05-13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The optional CP0_BadInstr and CP0_BadInstrP registers are written with the encoding of the instruction that caused a synchronous exception to occur, and the prior branch instruction if in a delay slot. These will be useful for instruction emulation in KVM, and especially for VZ support where reading guest virtual memory is a bit more awkward. Add CPU option numbers and cpu_has_* definitions to indicate the presence of each registers, and add code to probe for them using bits in the CP0_Config3 register. [ralf@linux-mips.org: resolve merge conflict.] Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/13224/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
generated by cgit v1.2.2 (git 2.25.0) at 2025-02-22 21:58:00 -0500